Gage Bilt GB713 User manual

Category
Power tools
Type
User manual
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
INSTALLATION TOOL
GB713
ORIGINAL INSTRUCTIONS
44766 Centre Court, Clinton Twp., MI. 48038 USA
Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505
[email protected] / www.gagebilt.com
GAGE BILT
MADE in USA
2
7/11 REV 3/23
GB713 Installation Tool
TABLE OF CONTENTS
Page
EU Conformity and Warranty ................................................................................................................................................... 3
Description and Technical Specifications ............................................................................................................................... 4
Description of Functions ........................................................................................................................................................... 5
Warnings ..................................................................................................................................................................................... 6
Principle of Operation ............................................................................................................................................................... 7
How to set-up the GB713 ........................................................................................................................................................... 8
How to use the GB713 ............................................................................................................................................................... 9
Maintenance ............................................................................................................................................................................. 10
Filling and Bleeding ................................................................................................................................................................. 11
Troubleshooting ...................................................................................................................................................................... 12
Stroke Limiter Instructions ..................................................................................................................................................... 12
Overhaul .............................................................................................................................................................................. 13-15
Parts Lists ................................................................................................................................................................................. 16
DEXRON® III Oil Safety Data (SDS) ........................................................................................................................................ 17
Nose Assembly Selection Chart ............................................................................................................................................. 18
Accessories ............................................................................................................................................................................. 20
3
7/11 REV 3/23
GB713 Installation Tool
DECLARATION OF CONFORMITY
MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct., Clinton Twp., Michigan U.S.A. +1 (586-226-1500)
WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS
TO THE FOLLOWING DIRECTIVES AND STANDARDS
Machinery Directive 2006/42/EC
EN12100-1 & EN12100-2
EN792-1:2000+A1
The Supply of Machinery (Safety) Regulations 2008
EU REPRESENTATIVE: Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany
EQUIPMENT DESCRIPTION: GB713 FASTENER INSTALLATION TOOL
This procuct specified above conforms to the above dIrectives and standards.
SIGNATURE:
NAME: TIM SIMMONS
PRODUCT MANAGER
CLINTON TWP., MI U.S.A.
JAN 2023
+1 (586) 226-1500
GAGE BILT
Seller warrants that all goods covered by this catalog will conform
to applicable specifications and will replace or repair, EXW our plant, any
goods providing defective from faulty workmanship, or material, for 1 year
from date of shipment.
Said warranty to remain in effect if, and only if, such goods are
used in accordance with all instructions as to maintenance, operation and
use, set forth in manuals and instruction sheets furnished by seller.
Sellers obligation under this warranty shall be limited to the repair
or rework of the goods supplied or replacement thereof, at Sellers option,
and in no case is to exceed the invoice value of said goods. Under no
circumstances will the seller be liable for incidental or consequential
damages or for damages incurred by the buyer or subsequent user in
repairing or replacing defective goods or if the goods covered by this
warranty are reworked or subjected to any type of additional processing.
This warranty is void if Seller is not notified in writing of any
rejections or defects within 1 year after the receipt of the material by the
customer.
THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES
EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY.
WARRANTY
4
7/11 REV 3/23
GB713 Installation Tool
SPECIFICATIONS
Hand Held Weight - 6.50 lbs. (2.9 kg)
Air pressure req'd - 90 - 100 p.s.i. (6.2 - 6.9 bar)
Air consumption - .30 SCF/cycle (8.50 L/cycle)
Hydraulic oil - Automatic Transmission Oil
Dexron III, or equivalent.
Setting stroke - .760" (19.3 mm)
Rated pull load - 4,500 lbs. (20.0 kN)
Noise level - 81.5 dB(A)
Vibration - Tested – No hazards found.
The GB713 is a pneumatic-hydraulic tool designed specifically for the efficient installation of blind rivets. It weighs 6.50 lbs. (2.9 kg)
and can be operated in any position. It has a .760" (19.3 mm) fastener setting stroke and a rated pull load of 4,500 lbs. (20.0 kN) with
90 psi (6.2 bar) air pressure at the air inlet.
The GB713 installation tool operates on 90 - 100 psi (6.2 - 6.9 bar) of air pressure, with 90 psi (6.2 bar) providing the maximum efficiency.
At 90 psi (6.2 bar) of air pressure, the GB713 does not exceed 81.5 dB(A) and consumes .30 SCF/cycle (8.50 L/cycle).
The air inlet is provided with 1/4 - 18 female pipe thread to accept the users air hose fitting.
NOSE ASSEMBLIES ARE NOT FURNISHED WITH TOOL AND MUST BE ORDERED SEPARATELY. (See nose assembly selection chart
on pg. 18 for nose assembly recommendations).
DESCRIPTION
WARNING: Any other use is forbidden.
ENVIRONMENTAL USE
WARNING: Do not operate in an explosive atmosphere.
The GB713 can be operated between 0ºF - 118ºF (-17.8ºC / 47.8ºC)
5
7/11 REV 3/23
GB713 Installation Tool
DESCRIPTION OF FUNCTIONS
Actuator
Handle Assembly
Head Cylinder Assembly
Pintail Deflector
Air Inlet
Actuator Lever Assembly
Hanger
Image may not reflect actual tool.
6
7/11 REV 3/23
GB713 Installation Tool
SAFETY WARNINGS
GENERAL SAFETY RULES:
1. For multiple hazards, read and understand the safety instructions before installing,
operating, repairing, maintaining, changing accessories on, or working near the
assembly power tool for non-threaded mechanical fasteners.
2. Only qualified and trained operators shall install, adjust or use the assembly power
tool for non threaded mechanical fasteners.
3. Do not modify this assembly power tool for non-threaded mechanical fasteners. Modifications can
reduce effectiveness of safety measures and increase the risks to the operator.
4. Do not discard safety instructions; give them to the operator.
5. Do not use assembly power tool for non-threaded mechanical fasteners if it has been damaged.
6. Tools shall be inspected monthly to verify all ratings and markings required are legible.
The employer/user shall contact the manufacturer to obtain replacement marking
labels when necessary.
ADDITIONAL SAFETY RULES FOR PNEUDRAULIC POWER TOOLS:
1. Air under pressure can cause severe injury.
2. Always shut off air supply, drain hose of air pressure and disconnect tool from air
supply when not in use, before changing accessories or when making repairs.
3. Never direct air at yourself or anyone else.
4. Whipping hoses can cause severe injury. Always check for damage or loose hoses and fittings.
5. Cold air shall be directed away from hands.
6. Whenever universal twist couplings (claw couplings) are used, lock pins shall be
installed and whip check safety cables shall be used to safeguard against possible
hose-to-tool or hose-to-hose connection failure.
7. Do not exceed the maximum air pressure stated on the tool or manual.
8. Never carry an air tool by the hose.
PROJECTILE HAZARDS:
1. Disconnect the tool from the energy source when changing inserted tools/nose as-
semblies or accessories.
2. Be aware that failure of the workpiece, accessories, or the inserted tool/nose assembly
itself can generate high-velocity projectiles.
3. Always wear impact resistant eye protection during operation of the tool.
4. Ensure that the workpiece is securely fixed.
5. Check that the means of protection from ejection of fastener and/or stem is in place
and operative (such as the deflector, pintail collection bottle or catcher bag).
6. Forcible ejection of the mandrel from the front of the nose assembly is possible.
OPERATING HAZARDS:
1. Use of tool can expose the operators hands to hazards, including crushing, impacts,
cuts, abrasions and heat. Wear suitable gloves to protect hands.
2. Operators and maintenance personnel shall be physically able to handle the bulk,
weight and power of the tool.
3. Hold the tool correctly; be ready to counteract normal or sudden movements and have
both hands available.
4. Maintain a balanced body position and secure footing.
5. Release the start-and-stop device in the case of interruption of energy supply.
6. Use only lubricants recommended by the manufacturer.
7. Avoid unsuitable postures as it is likely for these positions not to allow counteracting
of normal or unexpected movement of the tool.
8. If the tool is fixed to a suspension device, make sure that fixation is secure.
9. Beware of the risk of crushing or pinching if nose equipment is not fitted.
10. Due to the tool weight, it is recommended safety shoes be worn during operation.
11. It is recommended tool be operated not more than 50 out of every 60 minutes, where
prolonged use is expected.
REPETITIVE MOTIONS HAZARDS:
1. When using the tool, the operator can experience discomfort in the hands, arms,
shoulders, neck or other parts of the body.
2. While using the tool, the operator should adopt a comfortable posture while maintain-
ing a secure footing and avoiding awkward or off balanced postures. The operator
should change posture during extended tasks; this can help avoid discomfort and
fatigue.
3. If the operator experiences symptoms such as persistent or recurring discomfort, pain,
throbbing, aching, tingling, numbness, burning sensations or stiffness, these warning
signs should not be ignored. The operator should tell the employer and consult a
qualified health professional.
ACCESSORY HAZARDS:
1. Disconnect tool from energy supply before changing the nose assembly or accessory.
2. Use only sizes and types of accessories approved by the manufacturer. Do not use
other types or sizes of accessories.
WORKPLACE HAZARDS:
1. Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfac-
es caused by use of tool and also of trip hazards caused by the air line or hydraulic
hose.
2. Proceed with care in unfamiliar surroundings. There could be hidden hazards, such as
electricity or other utility lines.
3. The tool is not intended for use in potentially explosive atmospheres and is not insu-
lated against contact with electrical power.
4. Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if
damaged by the tool.
NOISE HAZARDS:
1. Exposure to high noise levels can cause permanent, disabling hearing loss and other
problems, such as tinnitus (ringing, buzzing, whistling or humming in the ears). There-
fore, risk assessment and the implementation of appropriate controls for these haz-
ards are essential.
2. Appropriate controls to reduce the risk may include actions such as damping materials
to prevent workpieces from ringing”.
3. Always use hearing protection.
4. Operate and maintain the assembly power tool for non-threaded mechanical fasteners
as recommended in the instruction handbook, to prevent an unnecessary increase in
the noise level.
5. Select, maintain and replace the consumable/inserted tool as recommended in the
instruction handbook, to prevent an unnecessary increase in noise.
6. If the power tool has a silencer, always ensure that it is in place and in good working
order when the power tool is being operated.
VIBRATION HAZARDS:
1. Exposure to vibration can cause disabling damage to the nerves and blood supply of
the hands and arms.
2. Wear warm clothing when working in cold conditions and keep your hands warm and
dry.
3. If you experience numbness, tingling, pain or whitening of the skin in your fingers or
hands, stop using the assembly power tool for non-threaded mechanical fasteners,
tell your employer and consult a physician.
4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip
can then be used to support the tool.
TERMS AND SYMBOLS
- Product complies with requirements
- Hearing protection and eye protection
WARNINGS - Must be understood to avoid severe
personal injury.
CAUTIONS - show conditions that will damage
equipment and/or structure.
Notes - are reminders of required procedures.
- Read manual prior to using equipment
- Wear safety boots
- Product complies with requirements
7
7/11 REV 3/23
GB713 Installation Tool
Air exhaust
PRINCIPLE OF OPERATION
When the air actuator assembly is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the
valve spool assembly causing the air to be redirected. The air is directed to the top of the air piston assembly, moving it in a downward
direction. The air below the air piston assembly is then directed through the valve sleeve and exhausted out of the bottom of the tool.
Simultaneously, the piston rod assembly, connected to the air piston assembly, is also moving down, forcing hydraulic oil up and into
the front side of the head cylinder assembly, causing the piston to move to the rear of the head cylinder assembly. The internal
components of the attached nose assembly are also moving with the piston to start the fastener installation. When the fastener
installation is completed, the air actuator assembly is released. Air pressure is then built up inside of the handle assembly causing
the valve spool assembly to return to its original position and reversing the sequence directing air pressure to the rear of the head
cylinder assembly, causing the piston to move to the forward position.
Images may not reflect actual tool.
Pressurized Oil
Unpressurized Oil
Pressurized Air
Unpressurized Air
RETURN Cycle
Air Piston
moves up
Piston Rod Assembly
moves up
Air exhaust
Air exhaust
Piston Rod Assembly
moves down
Air Piston
moves down
PULL Cycle
8
7/11 REV 3/23
GB713 Installation Tool
Image may not reflect actual tool
HOW TO SET-UP THE GB713
The tool is shipped with a red plastic plug in the air inlet connector. The connector has a 1/4 - 18 female pipe thread to accept user air
hose fitting. The tool comes with oil and is ready to use.
1. Remove red plastic shipping plug from Swivel (A-249) (air inlet) and screw in your quick disconnect (air) fitting.
2. Attach Deflector (704113) to rear of head cylinder assembly (713121). Rotate deflector (704113) away from operator or other
people working in the vicinity.
3. Connect tool to air hose with 90 psi. (6.2 bar) using clean, dry air. 3/8” (9.52 mm) minimum diameter air line is recommended.
Cycle tool five times by depressing and releasing actuator lever assembly (704343).
4. Disconnect air hose from tool.
5. Select proper nose assembly (nose assembly selection chart pg.18 for more information). Screw collet onto piston and slide anvil
over collet and secure with retaining nut (211102). (See proper data sheet for further instructions).
6. Connect air supply.
AIR HOSE
USER QUICK
DISCONNECT FITTING
RED SHIPPING PLUG
AIR INLET
HEAD CYLINDER ASSEMBLY NOSE ASSEMBLY
FASTENER
WORK
ACTUATOR
DEFLECTOR
WARNING: Only qualified and trained operators must install, adjust or use the assembly power tool for non-threaded
mechanical fasteners.
WARNING: Operator MUST read and understand all warnings and cautions.
WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this
equipment.
WARNING: The users or the users employer must assess specific risks that could be present as a result after each use
based on their application.
Ensure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of any
moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.
Verify the air lines and/or hydraulic hoses are not a trip hazard.
Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool.
WARNING: Do not actuate fastener in the air. Personal injury from fastener ejecting may occur.
WARNING: Air is exhausted from the bottom of the tool. Direct bottom of the tool (exhausted air) away from operator, other
persons working in the vicinity, foreign matter and liquid.
WARNING: Do not carry from hoses or use as a hammer.
WARNING: Do not use in explosive atmosphere.
WARNING: Ensure air hose is securely connected to avoid possible hose whipping.
WARNING: Always disconnect air supply when tool is not in use to prevent accidental start-up.
WARNING: Ensure there is adequate clearance for tool and operator hands.
WARNING: Do not operate this tool without deflector, pintail catcher bag or pintail collection bottle in place.
CAUTION: Do not use beyond the design intent.
9
7/11 REV 3/23
GB713 Installation Tool
Blind Fasteners
1. Insert fastener.
2. Insert fastener into nose assembly.
Note: Always hold tool so pulling head is perpendicular to surface of
material in which fastener is being installed. Exert firm pressure
against fastener during installation.
3. Press actuator to start cycle.
4. Release actuator as soon as fastener breaks.
5. Repeat steps 1 - 4.
Images may not reflect actual tool or fastener
HOW TO USE THE GB713
WARNING: Only qualified and trained operators must install, adjust or use the assembly power tool for non-threaded
mechanical fasteners.
WARNING: Operator MUST read and understand all warnings and cautions.
WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this
equipment.
WARNING: The users or the users employer must assess specific risks that could be present as a result after each use
based on their application.
Ensure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of any
moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.
Verify the air lines and/or hydraulic hoses are not a trip hazard.
Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool.
WARNING: Do not actuate fastener in the air. Personal injury from fastener ejecting may occur.
WARNING: Air is exhausted from the bottom of the tool. Direct bottom of the tool (exhausted air) away from operator, other
persons working in the vicinity, foreign matter and liquid.
WARNING: Do not carry from hoses or use as a hammer.
WARNING: Do not use in explosive atmosphere.
WARNING: Ensure air hose is securely connected to avoid possible hose whipping.
WARNING: Always disconnect air supply when tool is not in use to prevent accidental start-up.
WARNING: Ensure there is adequate clearance for tool and operator hands.
WARNING: Do not operate this tool without deflector, pintail catcher bag or pintail collection bottle in place.
CAUTION: Do not use beyond the design intent.
10
7/11 REV 3/23
GB713 Installation Tool
TORQUE SPECIFICATIONS
Button Head Cap Screws (402479) = 40 inch lbs. (4.52 Nm).
Packing Plug (744118) = 45 foot lbs. (61 Nm).
Flexlock Nut (400559) = 40 inch lbs. (4.52 Nm).
End Cap (713217) = 45 foot lbs. (61 Nm).
Button Head Cap Screws (402482) = 35 - 40 inch lbs. (3.95 - 4.52 Nm). (Do NOT over-tighten).
DAILY MAINTENANCE
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or
wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures.
WARNING: Excessive contact with hydraulic oil and lubricants must be avoided.
WARNING: Maintenance personnel MUST read and understand all warnings and cautions.
WARNING: Disconnect tool from its power source before performing maintenance, cleaning or when replacing worn or
damaged components. Severe personal injury may occur if power source is not disconnected.
WARNING: Read material Safety Data Sheet documents for all applicable materials.
CLEANING AND LUBRICATING PROCEDURE
Image may not
reflect actual tool
Daily cleaning and lubrication of nose assembly will greatly reduce downtime and increase life of components. Using sewing machine
oil, or an equivalent cleaner/lubricant, follow instructions below.
Note:
Dispose of hydraulic oil in accordance with manufacture safety datasheet.
All tool materials are recyclable except rubber orings, seals and wipers.
The performance of any tool depends upon good maintenance practices. Following these minimal requirements daily will extend the
life of your tool.
* Only use a clean dry air supply set at 90 - 100 p.s.i. (6.2 - 6.9 bar) Max. equipped with a filter-regulator to prevent wear.
* Check tool and nose assembly for damage. (Replace/Repair if necessary). See Overhaul pg. 13 - 15 for tool repair.
* Inspect hoses and couplings for wear, damage and leaks. (Replace/Repair if necessary).
* Verify that hydraulic hose fittings and couplings, air and electrical connections are secure. Tighten, Replace or Repair if necessary.
* Cycle the tool several times to assure there are no leaks during use.
* Keep hydraulic system free of dirt.
* Proper care by operators is necessary in maintaining full productivity and reducing downtime.
* Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride on with
light machine oil on a daily basis.
* All Screwed End Caps, Base Covers, Air Fittings, Air Actuators, Screws and Nose Assemblies are to be examined at the end of each
working shift to check that they are secure.
* For a complete overhaul, service tool kit (GB740TK) is recommended. See overhaul pg. 13 - 15.
WEEKLY MAINTENANCE
Keep the hydraulic system full (only use Dexro III or equivalent) and free of air by using the air bleeder assembly (704153) on a weekly
basis or as needed. (See Filling and Bleeding procedure pg. 11).
SEE TROUBLESHOOTING (PG. 12) AND OVERHAUL (PGS. 13 - 15) FOR FURTHER GUIDANCE.
LUBRICATING
Lubricate nose assembly after each cleaning
and as often as needed.
1. Disconnect tool vacuum line (if equipped).
2. Point nose assembly into oil as shown.
3. Cycle tool 8 - 10 times and wipe dry.
CLEANING
Clean nose assembly daily or as often as needed.
1. Dip into mineral spirits or similar solvent to clean
jaws and wash away metal chips and debris. DO
NOT allow jaws to come in contact with other solvents.
DO NOT let jaws soak. Dry jaws immediately.
2. Disassemble nose assembly and use a sharp pick
to remove embedded particles from grooves of jaws.
11
7/11 REV 3/23
GB713 Installation Tool
WARNING: Do not cycle tool without air bleeder assembly (704153), or the screw and stat-o-seal, installed in tool head. Severe
personal injury could result.
Use CAUTION when removing screws, air bleeder assembly (704153) and fill bottle (745263). Hydraulic oil may be
under pressure.
CAUTION: Before filling handle assembly (744129), air piston assembly (744121) must be all the way down.
CAUTION: When forcing piston rod assembly (744136) downward, with head cylinder assembly (713121) removed, hydraulic oil will
eject forcibly from handle assembly (744129).
CAUTION: When bleeding tool, ensure tubing is free from kinks or other obstructions.
FILLING & BLEEDING VIDEO AVAILABLE AT: http://www.gagebilt.com/rivet_tools_videos.php
BLEEDING PROCEDURE:
To replace a small amount of oil, DISCONNECT AIR FROM TOOL. Remove button head cap screw (402482) and stat-o-seal (S572)
from head cylinder assembly (713121). Install air bleeder assembly (704153) and connect tool to air line. Cycle ten times to fully
circulate oil through hydraulic system. DISCONNECT AIR FROM TOOL, remove the air bleeder assembly(704153), and reinstall button
head cap screw (402482) and stat-o-seal (S572) on head cylinder assembly (713121). Torque 35 - 40 inch lbs. (3.95 - 4.52 Nm). Do not
over tighten. This will ensure the removal of any air from the hydraulic system and its replacement with oil.
FILLING AND BLEEDING PROCEDURE: (required after tool has been dismantled).
1. Place piston rod wench assembly (704149) in power cylinder (743131) and carefully push piston rod assembly (744136) and air
piston assembly (744121) completely down.
2. Fill handle assembly (744129), power cylinder (743131) and the oil passage on top of handle assembly (744129) with automatic transmission
oil, Dexro III or equivalent. When looking at the top of the handle assembly (744129), the oil passage is the hole that is counterbored for
o'ring (S832). See image below.
3. Push piston (713211) full forward in head cylinder assembly (713121), then attach head cylinder assembly (713121) with care,
ensuring gasket (704129) and o'ring (S832) are properly installed. Apply Loctite® 242 to button head cap screws (402479) and
torque uniformly to 40 inch lbs. (4.52 Nm) to prevent leakage around gasket (704129).
4. ENSURE TOOL IS DISCONNECTED FROM AIR. Remove button head cap screw (402482) and stat-o-seal (S572) from head cylinder
assembly (713121). Install air bleeder assembly (704153) and connect tool to air line. Cycle ten times to fully circulate oil through
hydraulic system.
5. DISCONNECT AIR FROM TOOL. Remove air bleeder assembly (704153) and install button head cap screw (402482) and stat-o-seal
(S572) on head cylinder assembly (713121). Torque 35 - 40 inch lbs. (3.95 - 4.52 Nm). Do not over tighten.
6. Reconnect air and cycle tool 10 more times. Check tool stroke using instructions a thru c and diagrams below. We recommend
using dial calipers.
a. With the actuator assembly-air (704130) released check dimension (A).
b. Holding actuator assembly-air (704130) in, check dimension (B).
c. Subtract dimension (A) from dimension (B). If stroke doesnt check .760" (19.3 mm) min. (See figures below) follow
bleeding procedure above.
For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke.
Please contact Gage Bilt for more information.
FILLING AND BLEEDING PROCEDURE:
Images may not reflect actual tool.
Bleeder hole on head cylinder assembly
(713121). Button head cap screw
(402482) & stat-o-seal (S572)
Note:
Air Bleeder Assembly (704153) is required.
Oil Passage hole
Oring (S832)
Handle Assembly and
Power Cylinder hole
***Keep air
hole free
from oil***
Air Bleeder
Assembly
(704153)
12
7/11 REV 3/23
GB713 Installation Tool
Providing all maintenance conditions have been met, follow this systematic approach to diagnosis.
1. MORE THAN ONE PULL IS REQUIRED TO BREAK FASTENER.
a) Tool needs to be bled. (See filling and bleeding procedure pg. 11).
b) Spring has fatigued, replace.
c) Jaws are stripped or packed with chips. Clean or replace.
d) Incorrect nose tip.
2. SLOW OR PARTIAL OPERATION WHEN THE ACTUATOR LEVER ASSEMBLY (704343) IS DEPRESSED.
a) Polyseal (A-1119) and oring (400793) on the piston (713211) could be worn or damaged. Replace.
b) Back-up ring (S908) and oring (A-201) on the piston rod assembly (744136) could be worn or damaged. Replace.
c) Muffler (744143) or filter inside valve spool assembly (743142) may be plugged with dirt. Clean thoroughly and back-
blow with compressed air.
d) Hole in metering screw in valve spool assembly (743142) may be blocked or damaged. Hole diameter should be .028" (.71 mm).
Clear and size or replace.
3. NO OPERATION WHEN ACTUATOR LEVER ASSEMBLY (704343) IS DEPRESSED.
a) Tool seized due to mechanical failure or damaged parts.
4. OIL LEAKAGE.
a) DO NOT OPERATE WITH OIL LEAKING FROM TOOL. HIGH PRESSURE OIL MAY CAUSE SEVERE PERSONAL INJURY.
b) Any oil leaking externally should be traced to its source. An o'ring or seal that leaks should be replaced.
5. AIR BYPASS FROM VALVE HOUSING.
a) If the spring (744144) breaks or dislodges, air will flow freely through the muffler (744143). Replace or reset. Valve
spring installation tool (744251) is recommended.
b) Check o'rings on valve sleeve (743144), valve spool assembly (743142), and valve plug (744142). If worn or damaged,
replace. Valve sleeve removal tool (744152) is recommended.
6. FASTENER STEM JAMMED IN NOSE ASSEMBLY.
a) Nose assembly components require service. DISCONNECT AIR FROM TOOL, remove the nose from the tool and
disassemble. Replace worn or broken parts. Clean the surface the jaws ride on.
b) Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble.
c) Incorrect follower.
TROUBLESHOOTING
1. Disconnect air from tool.
2. Remove end cap.
3. Slide Stroke Limiter over rear Piston. (See Nose Assembly
Selection Chart pg. 18 to select Stroke Limiter)
4. Tighten End Cap onto tool. (See pg. 10 for torque setting)
STROKE LIMITER
Images may not reflect actual tool
STROKE LIMITER INSTRUCTIONS
13
7/11 REV 3/23
GB713 Installation Tool
TOOL DISPOSAL
1. When tool life is met, drain hydraulic oil from tool and dispose of the hydraulic oil in accordance with the safety datasheet.
2. Disassemble tool and remove all rubber orings, seals, wipers and hydraulic hoses. All tool materials are recyclable except rubber
orings, seals, wipers and hydraulic hoses. Dispose of rubber materials in accordance with the material safety datasheet.
OVERHAUL
WARNING: Only qualified and trained personnel shall perform overhaul.
WARNING: Personnel must read and understand all warnings and cautions.
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or
wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures.
WARNING: Disconnect tool from its power source before performing overhaul. Severe personal injury may occur if power
source is not disconnected.
WARNING: Excessive contact with hydraulic oil and lubricants must be avoided. (See safety data sheet documents for all
applicable materials).
WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or rear
of tool when installing fastener.
WARNING: Ensure air hose is securely connected to avoid possible hose whipping (Air Actuated Tools only).
WARNING: Depress actuator assembly-air (704130) and disconnect from air, with the piston in the rear position, before overhaul.
Severe personal injury may occur if air hose is not disconnected. USE CAUTION when forcing piston
rod assembly downward with head cylinder removed. Hydraulic oil will eject forcibly from handle assembly.
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use
of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings.
The disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and parts lists on pgs. 13 - 16.
Use extreme care during disassembly and re-assembly not to mar or nick any smooth surface that comes in contact with seals. Before
installing seals, always apply a good lubricant, such as Lubriplate®, to the surfaces.
Clean parts in mineral spirits or other o'ring compatible solvent being sure to clean o'ring grooves. Inspect components for scoring,
excessive wear or damage.
Part No. Description
704149 Piston Rod Wrench Assembly
704151 Power Cylinder Tool Assembly
704150 Packing Plug Wrench Assembly
704152 Seal Guide
704153 Air Bleeder Assembly
744251 Valve Spring Installation Tool
744152 Valve Sleeve Removal Tool
S1178 Valve Extractor
GB740TK Service Tool Kit Includes:
Note:
Dispose of hydraulic oil in accordance with manufacture safety datasheet.
All tool materials are recyclable except rubber orings, seals and wipers.
It is recommended that service tool kit (GB740TK) (see below) be used to facilitate overhaul.
Use of SERVICE KIT (713122), which contains a complete set of o'rings, back-up rings, screws, washers and gasket, can
achieve a complete overhaul.
14
7/11 REV 3/23
GB713 Installation Tool
REMOVING ACTUATOR ASSEMBLY-AIR (704130)
1. Remove actuator lever assembly (704343) including pin-slotted (400608) from the handle assembly (744129).
2. Insert a 5/8” open end wrench / adjustable wrench around actuator assembly-air (704130).
3. Loosen the actuator assembly-air (704130).
4. Remove wrench. Unthread and remove the actuator assembly-air (704130) with fingers
from the handle assembly (744129).
INSTALLING ACTUATOR ASSEMBLY-AIR (704130)
1. Apply Teflo tape onto threads of actuator assembly-air (704130) one to two wraps.
2. Thread the actuator assembly-air (704130) all the way into handle assembly (744129) with fingers.
3. Insert and turn 5/8” wrench / adjustable wrench and snug tight approximately 1/4 - 1/2 turn.
4. Re-attach actuator lever assembly (704343) including pin-slotted (400608) to the handle assembly (744129).
ACTUATOR ASSEMBLY-AIR
WARNING: Disconnect tool from its power source before actuator removal or installation. Severe personal injury may occur if
power source is not disconnected.
CAUTION: Actuator assembly-air (704130) can break if not careful.
CAUTION: Do not over tighten actuator assembly-air (704130). Snug tighten only.
OVERHAUL
15
7/11 REV 3/23
GB713 Installation Tool
WARNING: Disconnect tool from its air source before disassembly.
OVERHAUL
1. Remove nose assembly and adapter from tool before attempting disassembly of head cylinder assembly (713121).
2. Remove end cap (713217).
3. Push against threaded end of piston (713211) to slide it out of head cylinder assembly (713121). Be careful not to damage
threads or cause burrs on polished piston rod surface.
The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding procedure pg. 11). Apply Loctite® #242 and
torque the button head cap screws (402479) uniformly to 40 inch lbs. (4.52 Nm) to prevent leakage around the gasket (704129).
HEAD
HANDLE
To inspect air cylinder bore, remove base cover (744124). Any further disassembly will require removal of the head cylinder assembly (713121)
first.
For complete disassembly.
1. Remove base cover (744124).
2. Holding tool upright, remove four button-head cap screws (402479). Lift head cylinder assembly (713121) from handle assembly
(744129) and set aside o'ring (S832) and gasket (704129).
3. Empty all hydraulic oil into an approved container and dispose of in accordance with all environmental regulations applicable to your area.
4. Place piston rod wrench assembly (704149) down into top of power cylinder (743131) and into the hex of piston rod assembly
(744136). While holding the piston rod wrench assembly (704149), remove flexlock nut (400559) using a 7/16" socket wrench / adjustable
wrench. Still holding piston rod wrench assembly (704149), remove air piston assembly (744121) using packing plug wrench assembly
(704150), by turning counterclockwise.
5. When air piston assembly (744121) is completely free from piston rod assembly (744136), tap or push on the piston rod wrench assembly
(704149) to eject air piston assembly (744121) from bottom of handle assembly (744129).
6. After removal of air piston assembly (744121), slide piston rod assembly (744136) back up to the end of its travel. Using packing
plug wrench assembly (704150) remove packing plug (744118).
7. With packing plug (744118) removed, power cylinder (743131) can be removed by pushing on power cylinder tool assembly (704151)
when inserted into top of power cylinder (743131).
To reassemble the handle assembly (744129).
1. Reverse the above procedure, being certain that all o'rings are properly lubricated before installation. Torque packing plug (744118)
to 45 foot lbs. (61 Nm).
2. Attach the seal guide (704152) to the piston rod assembly (744136) and tap the piston rod assembly (744136) through the packing plug
(744118).
3. Attach air piston assembly (744121) and flexlock nut (400559). Torque flexlock nut to 40 inch lbs. (4.52 Nm).
4. Attach air piston assembly (744121) to piston rod assembly (744136).
5. With the piston rod in the down position, fill oil passage on top of handle assembly (744129) with automatic transmission oil, Dexron® III or
equivalent. When looking at top of handle assembly (744129) the oil passage is the hole that has a counterbore for (S832) o'ring.
6. Replace gasket (704129) and o'ring (S832), just prior to replacing head cylinder assembly (713121). Torque all screws to manual specifications.
(See filling and bleeding procedure pg. 11) & (See torque specifications on pg. 10).
AIR VALVE
1. Remove pin (744149) and muffler (744143).
2. Insert valve extractor (S1178) into end of valve plug (744142) and pull it out.
3. Using the same procedure, pull out valve spool assembly (743142).
4. It should never be necessary to remove valve sleeve (743144) unless the ports in the valve sleeve (743144) are plugged from
contaminated air. If ports are plugged, use needle nose pliers to grasp end of spring (744144), turning clockwise and pulling to
dislodge from groove in casting. Valve spring installation tool (744251) will facilitate the proper installation of the spring (744144).
5. Valve sleeve (743144) can be pulled out using valve sleeve removal tool (744152).
16
7/11 REV 3/23
GB713 Installation Tool
PARTS LIST
17
7/11 REV 3/23
GB713 Installation Tool
DEXRON® III OIL SAFETY DATA
FIRST AID MEASURES
Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water.
Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the material
from skin, use soap and water. Discard contaminated clothing and shoes or thoroughly clean before reuse.
Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get medical advice.
Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air, move the exposed person to
fresh air. Get medical attention if coughing or respiratory discomfort occurs.
Note to Physicians: In an accident involving high-pressure equipment, this product may be injected under the skin. Such an accident
may result in a small, sometimes bloodless, puncture wound. However, because of its driving force, material injected into a fingertip can
be deposited into the palm of the hand. Within 24 hours, there is usually a great deal of swelling, discoloration, and intense throbbing
pain. Immediate treatment at a surgical emergency center is recommended.
FIRE
Leaks/ruptures in high pressure system using materials of this type can create a fire hazard when in the vicinity of ignition sources (e.g.
open flame, pilot lights, sparks, or electric arcs).
FLAMMABLE PROPERTIES:
Flashpoint: (Cleveland Open Cup) 178 °C (352 °F) Minimum
EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.
PROTECTION OF FIRE FIGHTERS:
Fire Fighting Instructions: This material will burn although it is not easily ignited. See Section 7 for proper handling and storage. For fires
involving this material, do not enter any enclosed or confined fire space without proper protective equipment, including self-contained breathing
apparatus.
Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne solids, liquids, and gases including
carbon monoxide, carbon dioxide, and unidentified organic compounds will be evolved when this material undergoes combustion.
ACCIDENTAL RELEASE MEASURES
Protective Measures: Eliminate all sources of ignition in vicinity of spilled material.
Spill Management: Stop the source of the release if you can do it without risk. Contain release to prevent further contamination of soil,
surface water or groundwater. Clean up spill as soon as possible. Use appropriate techniques such as applying non-combustible
absorbent materials or pumping. Where feasible and appropriate, remove contaminated soil. Place contaminated materials in disposable
containers and dispose of in a manner consistent with applicable regulations.
ECOLOGICAL INFORMATION
Waste disposal: In accordance with all environmental regulations applicable to your area.
Spillage: Prevent entry into drains, sewers and water course. Soak up with diatomaceous earth or other inert material. Store in
appropriate container for disposal.
Ecotoxicity: This material is expected to be harmful to aquatic organisms and may cause long-term adverse effects in
the aquatic environment. The ecotoxicity hazard is based on an evaluation of data for the components or a similar material.
HANDLING
Precautionary Measures: DO NOT USE IN HIGH PRESSURE SYSTEMS in the vicinity of flames, sparks and hot surfaces. Use only in
well ventilated areas. Keep container closed. Keep out of the reach of children.
General Handling Information: Avoid contaminating soil or releasing this material into sewage and drainage systems and bodies of
water.
Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this material. To minimize this
hazard, bonding and grounding may be necessary but may not, by themselves, be sufficient. Review all operations which have the
potential of generating and accumulating an electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash
filling, tank cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations) and use appropriate
mitigating procedures.
DISPOSAL CONSIDERATIONS
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place
contaminated materials in containers and dispose of in a manner consistent with applicable regulations.
18
7/11 REV 3/23
GB713 Installation Tool
NOSE ASSEMBLY SELECTION CHART
Stroke Limiter
#713152
Required with all offset
204 nose assemblies
when used on GB713
tool.
See Chart.
(Sold Separately)
Stroke Limiter
#713153
Required with –54 right
angle nose assemblies
when used on GB713
tool. See Chart.
(Sold Separately)
Adapter Assembly
#751204
Adapts 204 offset series nose
assemblies to GB713 installation tool.
(Sold Separately)
Other adapters available. Contact
Gage Bilt for more information.
Gage Bilt also supplies pin
& collar swage inspection
gages to certify
swage installation.
(Sold Separately)
Grip Gage #269G3
For CHERRYMAX® and
CHERRYLOCK® rivets
(Sold Separately)
Grip Gage #GB105093
For NAS LOCKBOLTS and
blind fasteners
(Sold Separately)
FASTENER DIA. *RIGHT ANGLE
3/16 LB06-722-20 LB06-722-60
1/4 LB08-722-20 LB08-722-60
3/16 MG06-722-20 MG06-722-60
1/4 MG08-722-20 MG08-722-60
1/8 SB04-752C-20 SB04-752C-45
SB04-751C-54RA 4SB04-752B-43OS
5/32 SB05-752C-20 SB05-752C-45
SB05-751C-54RA 4 SB05-752A-43OS
SB05-752C-80
3/16 SB06-752B-20 SB06-752B-45
SB06-751B-54RA 4 SB06-204D-27OS 3 SB06-204D-37OS 3
SB06-752B-80
1/4
SB08-713-20 3SB08-713-45 3SB08-713A-58RA 3SB08-204D-27OS 3SB08-204D-37OS 3
1/8 UBB04-752C-20 UBB04-752C-45
UBB04-751C-54RA 4UBB04-752B-43OS
5/32 UBB05-752C-20 UBB05-752C-45 UBB05-751C-54RA UBB05-752B-43OS
UBB05-752C-80
3/16 UBB06-752B-20 UBB06-752B-45 UBB06-751B-54RA UBB06-204D-27OS UBB06-204D-37OS 3
UBB06-752B-80
1/4
UBB08-713-20 3UBB08-713-45 3UBB08-713A-58RA 3UBB08-204D-27OS 3UBB08-204D-37OS 3
5/32
UAB568-713-21 5UAB568-713-61 5
3/16
UAB06-751B-54RA 4 UAB06-752B-43OS
1/4 UAB08-204D-27OS UAB08-204D-37OS
1/8 SMLS04-752C-20 SMLS04-752C-45
SMLS04-751C-54RA 4 SMLS04-752B-43OS
5/32 SMLS05-752C-20 SMLS05-752C-45
SMLS05-751C-54RA 4 SMLS05-752B-43OS
3/16 SMLS06-752B-20 SMLS06-752B-45
SMLS06-751C-54RA 4 SMLS06-752B-43OS
1/4 SMLS08-713-20 SMLS08-713B-58RA
SMLS08-752B-43OS 2
3/32 3A-352B-25
3A-751C-54RA 4
1/8 4A-752C-20 4A-752C-45
4A-751C-54RA 4 4A-752B-43OS
5/32 5A-752C-20 5A-752C-45
5A-751C-54RA 4 5A-752B-43OS
3/16 6A-752B-20 6A-752B-45
6A-751C-54RA 4 6A-752B-43OS
1/4 SMLS08-713-20 SMLS08-204D-27OS
3/16 6T-352-21 6T-352-61
1/4 8T-352-21 8T-352-61
3/16 MGL06-752A-21 MGL06-752A-61 MGL06-713B-58RA
1/4 MGL08-752A-21 MGL08-752A-61 MGL08-713B-58RA
3/16 MB06-752A-21 MB06-752A-61
1/4 MB08-752A-21 MB08-752A-61
TLR RIVE 1/4 8TLR-352-21 8TLR-352-61
1/8
456MAX-751-23 1456MAX-751A-61 1 456MAX-751D-54RA 1,4 456MAX-731-43OS 1
5/32
3/16
1/4 08MAX-752B-20 08MAX-752B-45 08MAX-713A-58RA 08MAX-204D-27OS 08MAX-204D-37OS
13/64 ASP06-752C-20 ASP06-752C-45
ASP06-751C-54RA 4 ASP06-752B-43OS
17/64 ASP08-752B-20 ASP08-752B-45 ASP08-752B-43OS
21/64 ASP10-713-20 ASP10-713-45 ASP10-204D-27OS ASP10-204D-37OS
1/8 MBC04-752C-20 MBC04-752C-45
MBC04-751C-54RA 4 MBC04-752C-43OS
5/32 MBC05-752C-20 MBC05-752C-45
MBC05-751C-54RA 4 MBC05-752C-43OS
3/16 MBC06-752B-20 MBC06-752B-45
MBC06-751C-54RA 4 MBC06-752C-43OS
1/8
5/32
456MAX-751-23 1456MAX-751A-61 1 456MAX-751D-54RA 1,4 456MAX-731-43OS 1
3/16
8/32 GS8-752C-20 GS8-752C-45
GS8-751C-54RA 4 GS8-752B-43OS
10/32 GS10-752B-20 GS10-752B-45
GS10-752A-54RA 4 GS10-752B-43OS
4mm 5N-751-23 5N-352-61
45N-751B-54RA 4 5N-751A-43OS
5mm 6N-751-23 6N-352-61
6N-751C-54RA 4 6N-751A-43OS
5/32 5N-751-23 5N-352-61
45N-751B-54RA 4 5N-751A-43OS
3/16 6N-751-23 6N-352-61
6N-751C-54RA 4 6N-751A-43OS
1/4 8CN-713-21 8CN-713-61 8N-713A-58RA
5/32 5CES-751-23 5CES-352-61
5CES-751B-54RA 4 5CES-751-43OS
3/16 6CES-751-23 6CES-352-61
6CES-751C-54RA 4 6CES-751-43OS
1/4 8CES-713A-58RA
GAGE BILT CERTIFIES THE GB713 WILL INSTALL THE ABOVE FASTENERS
BLIND BOLT (SINGLE ACTION)
WITH DRIVE WASHER
MS90353S & U / MS90354S & U
MS21140S & U / MS21141S & U
CR7000 SERIES,
BACB30YY, YU, & YT
6CEA-751-43OS
HT12-713-20
MILLIMETER PLUG SEAL
3/8
POP® OPEN END
NAIL RIVET
POP® CLOSED END
NAIL RIVET
(ALUMINUM MANDREL)
POP® CLOSED END
NAIL RIVET
(STEEL MANDREL)
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
5CEA-751-43OS
3/16
6CEA-751-23
6CEA-352-61
T RIVET®, CHERRYM A , MAXI-BOLT®, AND M B C® ARE REGISTERED TRADEM ARKS OF CHERRY A EROSPACE. M ONOB OLT® AND TLR® ARE REGISTERED TRADEMARKS OF
AVDEL UK LIMITED. ASP ®, M A GNA-GRIP® AND C6L® ARE REGISTERED TRA DEM A RKS OF HOWMET AEROSP A CE.
5CEA-352-61
5/32
BLIND RIVET (SINGLE ACTION)
WITH OR W/OUT DRIVE WASHER
NAS1900 S & U SERIES
"A" CODE
NAS1398A & NAS1399A
MONOBOLT®
GROUND STUD,
M83454 BACS53B
5CEA-751-23
*OFFSET
C6L® LOCKBOLTS
MAGNA-GRIP® LOCKBOLTS
CONTAINER BOLT(R 12)
HLPP, HLPM, HLPE, HLPS
HLPSC & HLPSM
PROTRUDING HEAD,
MULTI-GRIP BLIND RIVETS
STRAIGHT
BLIND BOLT (SINGLE ACTION)
WITH OR W/OUT DRIVE WASHER
MS90353S & U / MS90354S & U
MS21140S & U / MS21141S & U
MAXI-BOLT®, BACB30YY, YU, &
YT
EN6122 & UAB130-EU
EN6127 & UAB6127-EU
EN6128 & UAB100-EU
EN6129 & UABP-EU
T RIVET®
4) THESE NOSES REQUIRE 713153 STROKE LIMITER.
5) INSTALLS 5/32", 3/16", AND 1/4"
MBC® LOCK CREATOR
NAS1719X(L), NAS1720X(L)
NAS1721X(L)
CHERRYMAX®,
CHERRYMAX® 'AB',
(FOR 1/4" ALUMINUM
CHERRYMAX® 'AB' USE SMLS08)
BACR15FR/FP, BACR15GF/GK
*ALL OFFSET 204 SERIES NOSES REQUIRE 751204 ADAPTER & 713152 STROKE LIMITER.
1) INSTALLS 1/8", 5/32" AND 3/16" DIAMETERS.
2) ALUMINUM ONLY.
3) 105 P.S.I. REQUIRED FOR MS90353 & MS90354.
ASP®
ASP 2, ASP PF, ASP 4 FF,
ASP 2 F, ASP 2 LC
STANDARD MBC®
NAS1719, NAS1720
NAS1721
Rev. 3/23
RIGHT ANGLE
(Sold Separately)
OFFSET
(Sold Separately)
STRAIGHT
(Sold Separately)
GB713 ACCESSORIES
Approved for use on Gage Bilt CE installation tools and/or other manufacturers CE approved tools of similar design.
(Sold Separately)
19
7/11 REV 3/23
GB713 Installation Tool
This page intentionally left blank.
20
7/11 REV 3/23
GB713 Installation Tool
CHERRYMAX® & CHERRYLOCK® ARE REGISTERED TRADEMARKS OF CHERRY AEROSPACE FASTENERS. DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION.
LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING CO. LOCTITE® IS A REGISTERED TRADEMARK OF HENKEL CORPORATION. TEFLON® IS REGISTERED TRADEMARK
OF E.I. DUPONT DE NEMOURS & CO.
Catcher Bag-Stem
#704214
(Sold Separately)
Alternative Styles
(Sold Separately)
GB713SH
Stroke - .760" (19.3 mm)
Hand held weight - 2.50 lbs. (1.1 kg)
Entire tool weight - 7.50 lbs. (3.4 kg)
Pull load - 4,500 (20.0 kN)
GB713SR
Stroke - .760" (19.3 mm)
Hand held weight - 2.00 lbs. (0.9 kg)
Entire tool weight - 7.00 lbs. (3.2 kg)
Pull load - 4,500 (20.0 kN)
Air Bleeder Assembly
#704153
(Sold Separately)
Riveter Kits Available
(Sold Separately)
Contact Gage Bilt to customize your riveter kit today.
Tool Stroke Depth Gage
#A-1935
(Sold Separately)
Image may not reflect actual gage
Accessories Cont.
Approved for use on Gage Bilt CE installation tools and/or other manufacturers CE approved tools of similar design.
(Sold Separately)
CE
Approved
CE
Approved
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Gage Bilt GB713 User manual

Category
Power tools
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI