Noble House 306367 Installation guide

Label Picture Description QTY

A Backrest Panel 1

B Left Arm Panel 1

C Right Arm Panel 1

Caution : You must read this before you proceed

CHAIR

Picture

Page 1 OF 27

D Seat Panel 1

E Back Panel 1

F Front Panel 1

Label Picture Description QTY

①

Long Screws

(M7x130mm)

4

②

Medium Screws

(M7x60mm)

2

③

Short Screws

(M6x50mm)

2

④

Allen Key 1

Before Beginning Assembly:

Page 2 OF 27

Step 1

Step 2

This Chair has multiple parts and may require up to some 30

minutes to assemble. To give you an overview of the Chair parts,

the above picture is to help you put the various parts into

perspective. Please read through the instructions below to

familiarise yourself with the parts and steps before assembly.

Unpack and place all parts on a clean, non-marring surface.

Overview

FRONT FACING

Page 3 OF 27

Step 3

Step 4

Then continue position Seat Panel (D) as show in picture above

Place the Left Arm Panel (B) and Right Arm Panel (C) onto a clean,

soft surface to avoid any scratches or damages to the product.

Align the tenon of Left Arm Panel (B) and Right Arm Panel (C) into

the Mortise of Back Panel (E) and Front Panel (F) as shown above.

Then, affix the Left Arm Panel (B) and Right Arm Panel (C) with

Back Panel (E) and Front Panel (F) by using Long Screws (①) and

Allen Key (

④

).

DO NOT FULLY TIGHTHEN SCREWS.

Page 4 OF 27

Step 5

Step 6

Position the Backrest Panel (A) as show in picture above.

Then, affix Backrest Panel (A) with Left Arm Panel (B) and Right

Arm Panel (C) by using Medium Screws (

②

) and Allen Key (

④

)

DO NOT FULLY TIGHTHEN SCREWS.

Insert the Tenons from Back Panel (E) into the Mortises of the

Backrest Panel (A) then attach using Short Screws (

③

) and Allen

Key (

④

).

DO NOT FULLY TIGHTHEN SCREWS.

Page 5 OF 27

Place the Chair on a LEVEL SURFACE.

Inspect it and make sure all parts are adequately connected.

Gently and gracefully, sit into to the Chair.

This will help to align all the parts at all the joint areas.

Then get off the Chair, and proceed to tighten all Screws in a

sequential manner.

You may be required to turn the Chair to gain easy access to the

secure points.

Turn the Chair in a synchronised manner.

CAUTION 1: When tightening these Screws, tighten sequentially.

DO NOT tighten any Screw fully and then towards the next one.

This would cause the frame to warp.

If there is still wobbles, loosen the Screws and execute this same

process.

WARNING!! IF CHAIR IS NOT STABLE , IT COULD LEAD TO

DAMAGING THE PRODUCT.

Ensure all Screws are fully locked into position.

The Chair is ready to be used.

Caution 2: This Chair can only be used on a flat, level surface.

Page 6 OF 27

Questions & Answers about Proposition 65

• What is Proposition 65?

Proposition 65 requires businesses to provide warnings to Californians about significant

exposures to chemicals that cause cancer, birth defects or other reproductive harm.

These chemicals can be in the products that Californians purchase, in their homes or

workplaces, or that are released into the environment. By requiring that this information be

provided, Proposition 65 enables Californians to make informed decisions about their

exposures to these chemicals.

Proposition 65 also prohibits California businesses from knowingly discharging significant

amounts of listed chemicals into sources of drinking water.

Proposition 65 requires California to publish a list of chemicals known to cause cancer,

birth defects or other reproductive harm. This list, which must be updated at least once a

year, has grown to include approximately 900 chemicals since it was first published in

1987.

• What types of chemicals are on the Proposition 65 list?

The list contains a wide range of naturally occurring and synthetic chemicals that include

additives or ingredients in pesticides, common household products, food, drugs, dyes, or

solvents. Listed chemicals may also be used in manufacturing and construction, or they

may be byproducts of chemical processes, such as motor vehicle exhaust.

• What does a warning mean?

If a warning is placed on a product label or posted or distributed at a workplace, a

business, or in rental housing, the business issuing the warning is aware or believes that it

is exposing individuals to one or more listed chemicals.

By law, a warning must be given for listed chemicals unless the exposure is low enough to

pose no significant risk of cancer or is significantly below levels observed to cause birth

defects or other reproductive harm.

• Where can I get more information on Proposition 65?

If you have specific questions on the administration or implementation of Proposition 65,

you can contact OEHHA's Proposition 65 program at [email protected], or by

phone at (916) 445-6900.

Page 7 OF 27

Page 8 OF 27

Label Picture Description QTY

A Backrest Panel 1

B Left Arm Panel 1

C Right Arm Panel 1

Caution : You must read this before you proceed

LOVESEAT

Picture

Page 9 OF 27

D Seat Panel 1

E Back Panel 1

F Front Panel 1

Label Picture Description QTY

①

Long Screws

(M7x130mm)

4

②

Medium Screws

(M7x60mm)

2

③

Short Screws

(M6x50mm)

4

④

Allen Key 1

Before Beginning Assembly:

Page 10 OF 27

Step 1

Overview

This Chair has multiple parts and may require up to 30 minutes to

assemble. To give you an overview of the Chair parts, the above picture

is to help you put the various parts into perspective. Please read

through the instructions below to familiarise yourself with the parts and

steps before assembly.

FRONT FACING

Page 11 OF 27

Step 2

Step 3

Unpack and place all parts on a clean, non-marring surface.

Place the Left Arm Panel (B) and Right Arm Panel (C) onto a clean, soft

surface to avoid any scratches or damages to the product.

Align the tenon of Left Arm Panel (B) and Right Arm Panel (C) into the

Mortise of Back Panel (E) and Front Panel (F) as shown above.

Then, affix the Left Arm Panel (B) and Right Arm Panel (C) with Back

Panel (E) and Front Panel (F) by using Long Screws (①) and Allen Key

(

④

).

DO NOT FULLY TIGHTHEN SCREWS.

Page 12 OF 27

Step 4

Position Seat Panel (D) as shown above.

Position the Backrest Panel (A) as show in picture above.

Then, affix Backrest Panel (A) with Left Arm Panel (B) and Right Arm

Panel (C) by using Medium Screws (

②

) and Allen Key (

④

)

DO NOT FULLY TIGHTHEN SCREWS.

Page 13 OF 27

Step 5

Step 6

Position Backrest Panel (A) as show in picture above.

Insert the Tenons from Back Panel (E) into the Mortises of the Backrest

Panel (A) then attach using Short Screws (③) and Allen Key (④).

DO NOT FULLY TIGHTHEN SCREWS.

Page 14 OF 27

Place the Loveseat on a LEVEL SURFACE.

Inspect it and make sure all parts are adequately connected.

Gently and gracefully, sit into to the Loveseat.

This will help to align all the parts at all joint areas.

Then get off the Loveseat and proceed to tighten the Bolts and Screws

in a sequential manner.

When tightening the Bolts and Screws tighten sequentially.

DO NOT tighten any Bolt or Screw fully and then move on towards the

next one.

If there are still wobbles, loosen the Bolts and Screws and execute this

same process.

Page 15 OF 27

Questions & Answers about Proposition 65

• What is Proposition 65?

Proposition 65 requires businesses to provide warnings to Californians about significant

exposures to chemicals that cause cancer, birth defects or other reproductive harm. These

chemicals can be in the products that Californians purchase, in their homes or workplaces, or

that are released into the environment. By requiring that this information be provided,

Proposition 65 enables Californians to make informed decisions about their exposures to these

chemicals.

Proposition 65 also prohibits California businesses from knowingly discharging significant

amounts of listed chemicals into sources of drinking water.

Proposition 65 requires California to publish a list of chemicals known to cause cancer, birth

defects or other reproductive harm. This list, which must be updated at least once a year, has

grown to include approximately 900 chemicals since it was first published in 1987.

• What types of chemicals are on the Proposition 65 list?

The list contains a wide range of naturally occurring and synthetic chemicals that include

additives or ingredients in pesticides, common household products, food, drugs, dyes, or

solvents. Listed chemicals may also be used in manufacturing and construction, or they may be

byproducts of chemical processes, such as motor vehicle exhaust.

• What does a warning mean?

If a warning is placed on a product label or posted or distributed at a workplace, a business, or

in rental housing, the business issuing the warning is aware or believes that it is exposing

individuals to one or more listed chemicals.

By law, a warning must be given for listed chemicals unless the exposure is low enough to pose

no significant risk of cancer or is significantly below levels observed to cause birth defects or

other reproductive harm.

• Where can I get more information on Proposition 65?

If you have specific questions on the administration or implementation of Proposition 65, you can

contact OEHHA's Proposition 65 program at [email protected], or by phone at

(916) 445-6900.

Page 16 OF 27

Page 17 OF 27

Label Picture Description

A Table Top

B Leg

Caution : You must read this before you proceed

TABLE

Picture

Page 18 OF 27

Label Picture Description

①

Bolt (M8x70mm)

②

Washer (M8 mm)

③

Allen Key

Before Beginning Assembly:

Page 19 OF 27

Step 1

Step 2

Overview

This Table has multiple parts and may require up to 30 minutes to assemble. To

give you an overview of the Table parts, the above picture is to help you put the

various parts into perspective. Please read through the instructions below to

familiarise yourself with the parts and steps before assembly.

Unpack and place all parts on a clean, non-marring surface.

FRONT FACING

Page 20 OF 27

Page is loading ...

Noble House 306367 Installation guide

Noble House 306367 Installation guide

Related papers

Other documents