LG LVC-DV101HM Owner's manual

Brand: LG

Model: LVC-DV101HM

Category: Security cameras

Type: Owner's manual

This manual is also suitable for

LVC-DV100HM

Operating Instructions

LVC-DV100 HM HP

LVC-DV101 HM HP

P/NO: 3834RC0022H

Before installing and using the camera,

please read these instructions thorough-

ly and retain them for later reference.

Regulatory Notices

For U.S.A

This equipment has been tested and found

to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful inter-

ference in a residential installation! This

equipment generates, uses and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruc-

tions, may cause harmful interference to

radio communications.

However, there is no guarantee that interfer-

ence will not occur in a particular installation.

If this equipment does cause harmful inter-

ference to radio or television reception,

which can be determined by turning the

equipment off and on, the user is encour-

aged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

This Class A digital apparatus meets all

requirements of the Canadian Interference-

Causing Equipment Regulations.

This symbol is intended to alert

the user to the presence of

uninsulated “dangerous voltage”

within the product’s enclosure

that may be of sufficient

magnitude to constitute a risk

of electric shock to persons.

The exclamation point within an

equilateral triangle is intended

to alert the user to the presence

of important operating and

maintenance (servicing)

instructions in the literature

accompanying the product.

CAUTION TO REDUCE THE RISK OF

ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE,

REFER SERVICING TO QUALIFIED SER-

VICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Warning

To prevent fire or shock hazard, do not expose

the unit to rain or moisture.

To avoid electrical shock, do not open

the cabinet Refer servicing to qualified

personnel only.

Wiring methods shall be in accordance with

the National Electric Code, ANSI/NFPA 70.

This product is manufactured to comply with the radio interference

requirements of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and

73/23/EEC.

1 Safety Precautions

Do not use strong

solvents or detergents

Use a dry cloth to the camera when it is

dirty. If it is hard to remove the dirt on

the camera, use a mild detergent and

wipe it gently.

Before operating, please

check proper temperature,

humidity and power

source ratings.

Use the camera under conditions where

temperature is between -10°C ~ 50°C.

Avoid the camera with

direct sunlight

Do not aim the camera at bright objects.

Never face it with direct sunlight or other

extremely bright objects. Otherwise

blooming or smear may be caused.

Do not attempt to disas-

semble the camera

To prevent electric shock, do not remove

screws or covers. There are no user

serviceable parts inside. Ask a qualified

service personnel for servicing

Handle the camera

with care

Do not abuse the camera. Avoid striking,

shaking, etc. The camera could be dam-

aged by improper handling or storage.

Do not expose the cam-

era to rain or moisture

This product is designed for indoor use

or location where it is protected from

rain and moisture. When exposed to

moisture, turn the power off immediate-

ly and ask a qualified service personnel

for servicing. Moisture can damage the

camera and also create the danger of

electric shock.

Do not expose the camera

in such conditions as

shown below.

Use in a room or area filled with ciga-

rette smoke, dust or gas.

2 What's in the box

Camera Body

M4 Tapping Screws

(2EA)

(Pan Lock Screw)

Adapter

(DC 12V, 300mA)

Video Cable

Optional

3 Construction

 Front View

 Side View

LG logo

4-pin Dip Switch

Tilt Base

Zoom Lever

Tilting Lock Screw

Focus Lever

Dome Cover

Lens

Tilting Lock Screw

Dome Cover Separatory

Spring

4 Construction

 Rear View

DC12V

(+) (-)

VIDEO NC

Dome Cover Separatory

Spring

Power In

Video Out

N.C

(Option: Ext. Sync.

or Audio)

GND

Pan Base

Base Fixing Hole

5 Installation

 Video Cable Connection

1. RED : Connect the RED Cable to 1(+).

2. BLACK : Connect the BLACK Cable to 2(-).

3. WHITE : Connect the WHITE Cable to 3(V).

DC12V

(+) (-)

VIDEO NC

RED Cable

BLACK Cable

WHITE Cable

6 Installation

 Camera Installation

1. Aim the LG logo of the Dome Camera to face the place that

you wish to watch.

2. Tighten the M4 Tapping Screws to fix the Dome Camera on

the ceiling, then adjust the Pan(Left /Right) by moving the

Pan Base. Tighten the M4 Tapping Screws after adjustment.

3. Loosen the Tilting Lock Screw. Adjust the Tilt(Up /Down) by

moving the Tilt Base then tighten Tilting Lock Screw.

4. Set the Zoom Lever to a point between

Tele and Wide to

choose the desired angular field of view.

Set the Focus Lever to a point between Near and Far to

choose the desired focus of view.

5. Install the Dome Cover to the main body by turning it coun-

terclockwise to the end.

Dome Cover

Focus Lever

(Near/Far)

Pan Base

Hole for Fixing

Tilting Lock Screw

Zoom Lever

(Tele/ Wide)

Tilt Base

7 Installation

NOTE

•

When you disassemble the Dome Cover, lift the Dome Cover

Separatory Spring on the opposite side of LG Logo and turn

the Dome Cover clockwise simultaneously.

•

When you install the camera, handle with care. The camera

could be damaged by improper handling or storage.

•

If this camera is mounted on the other places except ceiling,

you need an extra bracket for mounting.(not supplied)

Dome Cover

Separatory Spring

8 Installation

 Camera Connection

Connect the Power Adapter (DC12V, 300mA; optional) to the

Power Input Jack of the camera as shown below.

Power

Input Jack

Adapter

Jack

DC12V

(+) (-)

VIDEO NC

Adapter

Rear Panel

BNC

Monitor

9 Setup

 4-pin Dip Switch Setting

This camera has the 4-pin Dip Switch inside of the camera for

setting.

1. ALC / ELC : ELC (Electronic IRIS), ALC (Auto IRIS)

The default setting is ALC.

2. Y/ DC IRIS : When you use Video Lens or DC IRIS Lens

The default setting is DC.(using the fixed lens)

3. BLC : Backlight Compensation

The default setting is OFF.

4. ABL : Auto BLC

The default setting is OFF.

NOTE

No. 1 and 2 must be set as a default mode. Depending on the

conditions, No.3 and 4 are adjustable.

(Backlight Compensation : refer to the next page)

ALC Y BLC ABL

ELC DC OFF OFF

10 Setup

 Backlight Compensation Setting

Backlight compensation eliminates strong background light

which makes the camera picture dark such as a spotlight. You

can select the mode for adjusting the iris lens. There are two

mode as follows.

1. BLC : Set the BLC to ON. The lens iris is manually fixed at

the value that you have set regardless of an object.

2. ABL : Set the ABL to ON. The lens iris is automatically

adjusted according to the brightness of an object.

ALC Y BLC ABL

ELC DC OFF OFF

ALC Y BLC ABL

ELC DC OFF OFF

11 Troubleshooting

Check the following guide for the possible cause of a problem

before contacting service.

•

The picture is poor.

Does the Dome Cover have lots of dust on the surface?

Use a dry cloth to clean the camera when it is dirty.

Smear may be caused to the screen of night than daytime.

Adjust the Focus by moving the Focus Lever.

•

Contrast of the screen is not clear.

Check the condition of the monitor.

Alight source such as a spot light causes burn-in on the

display screen. Adjust position or angle of the camera to

eliminate strong background light.

•

Background screen appears white extremely.

You can set the background compensation to OFF.

12 Dimension

DC12V

(+) (-)

VIDEO NC

ø 90

ø100

91mm

31mm

ø121.5

10mm

13 Specifications

Model

LVC-DV100/101HM LVC-DV100/101HP

Signal System NTSC PAL

Total / Effective Pixels 410K/380K 470K/440K

Pick-Up Device 1/3-Inch Interline Color CCD (Super HAD)

Lens

Vari-Focal Lens

f=2.6 ~ 6.0mm/F=1.4, f=4.0 ~ 9.0mm/F=1.6 *

Angular Field of View

125

°~60.0°(

f=2.6~6.0mm

)

92.6

°~39.4°(

f=4.0~9.0mm

)

Focus Manual

Signal Process Digital Signal Process

Scanning System 2 : 1 Interlace

Sync. System Internal

Scanning Frequency 59.94 Hz(VD) 50Hz(VD)

Resolution 480 Line (H) 470 Line (H)

S/N Ratio More than 48dB

Standard Illuminance 2000Lux (3200

° K)

Sensitivity (1/3 output) 0.5 Lux (F1.2)

Video Output Signal 1Vp-p Composite (75Ω)

Gain Control Auto

Shutter Speed

Electronic Shutter Electronic Shutter

(1/60~1/10000) (1/50~1/10000)

White Balance Auto

Back Light Compensation ON/OFF, AUTO

Power Source DC12V

Power Consumption 2.3W

Operating Temp. -10°C ~ 50°C (Humidity : 0%RH ~ 60RH)

Storage Temp. -20°C ~ 60°C (Humidity : 0%RH ~ 85RH)

Weight 251g

Dimensions

ø121.5

(Diameter)x91(H), Dome Size=

ø100

LVC-DV100HM/HP : f=4.0 ~ 9.0mm

LVC-DV101HM/HP : f=2.6 ~ 6.0mm

Design and specifications are subject to change without notice.

MEMO

LG LVC-DV101HM Owner's manual

Brand: LG

Model: LVC-DV101HM

Category: Security cameras

Type: Owner's manual

This manual is also suitable for

LVC-DV100HM

Download PDF

report

LG LVC-DV101HM Owner's manual

This manual is also suitable for

LG LVC-DV101HM Owner's manual

Related papers

Other documents