Scholtes TIS 621 CT L Owner's manual

Page is loading ...

Operating Instructions

HOB

TIS 621 CT L

Italiano, 1

GB

Espanol, 49

ES

Deutsch, 37

DE

Français, 13 English,25

IT FR

Contents

Installation, 26-27

Positioning

Electrical connection

Description of the appliance, 28

Control panel

Start-up and use, 29-33

Switching on the hob

Switching on the cooking zones

Medium function

Booster function

Switching off the cooking zones

Programming the cooking duration

Timer

Control panel lock

Switching off the hob

“Demo” mode

EXTENSO TECHNOLOGY mode

Practical advice on using the appliance

Safety devices

Practical cooking advice

Precautions and tips, 34

General safety

Disposal

Care and maintenance, 35

Switching the appliance off

Cleaning the appliance

Disassembling the hob

Technical description of the models, 36

26

GB

Installation

! Before operating your new appliance please read this

instruction booklet carefully. It contains important

information concerning the safe operation, installation and

maintenance of the appliance.

! Please keep these operating instructions for future

reference. Pass them on to any new owners of the

appliance.

Positioning

! Keep all packaging material out of the reach of children.

It may present a choking or suffocation hazard (

see

Precautions and tips

).

! The appliance must be installed by a qualified

professional in accordance with the instructions provided.

Incorrect installation may cause harm to people and

animals or may damage property.

Built-in appliance

Use a suitable cabinet to ensure that the appliance

functions properly.

• The supporting surface must be heat-resistant up to a

temperature of approximately 100°C.

• If the appliance is to be installed above an oven, the

oven must be equipped with a forced ventilation

cooling system.

• Avoid installing the hob above a dishwasher: if this

cannot be avoided, place a waterproof separation

device between the two appliances.

• Depending on the hob you want to install, the cabinet

must have the following dimensions (

see figure

):

560 +/- 1

490 +/- 1

48

590

520

690

520

560 +/- 1

490 +/- 1

48

Ventilation

To allow adequate ventilation and to avoid overheating of the

surrounding surfaces the hob should be positioned as follows:

• At a minimum distance of 40 mm from the back panel

or any other vertical surfaces.

• So that a minimum distance of 20 mm is maintained

between the installation cavity and the cabinet

underneath.

• Kitchen cabinets adjacent to the appliance and taller

than the top of the hob must be at least 600 mm from

the edge of the hob.

FRONT SIDE

OF HOB

SUPPORTING

SURFACE

30

40

UNDERSIDE

OF HOB

5 mm

min. 20 mm

min. 40 mm

COMPARTMENT

5 mm

min. 40 mm

FAN-ASSISTED

OVEN

27

GB

Fixing

The appliance must be installed on a perfectly level

supporting surface.

Any deformities caused by improper fixing could affect

the features and operation of the hob.

The thickness of the supporting surface

should be taken

into account when choosing

the length of the screws for the

fixing hooks:

• 30 mm thick: 23 mm screws

• 40 mm thick: 13 mm screws

Fix the hob as follows:

1. Use short flat-bottomed screws to fix the 4 alignment

springs in the holes provided at the central point of each

side of the hob.

2. Place the hob in the cavity, make sure it is in a central

position and push down on the whole perimeter until the

hob is stuck to the supporting surface.

3. For hobs with raised sides: After inserting the hob into

its cavity, insert the 4 fixing hooks (each has its own pin)

into the lower edges of the hob, using the long pointed

screws to fix them in place, until the glass is stuck to the

supporting surface.

! The screws for the alignment springs must remain

accessible.

! In order to adhere to safety standards, the appliance

must not come into contact with electrical parts once it

has been installed.

! All parts which ensure the safe operation of the

appliance must not be removable without the aid of a tool.

Electrical connection

! The electrical connection for the hob and for any built-in

oven must be carried out separately, both for safety

purposes and to make extracting the oven easier.

Single-phase connection

The hob is equipped with a pre-connected electricity

supply cable, which is designed for single-phase

connection. Connect the wires in accordance with the

instructions given in the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

220-240V 1+N ~

50 Hz

: yellow/green

N

: the two blue wires together

L

: brown and black together

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

• 400V - 2+N ~ 50 Hz

• 220-240V 3 ~ 50 Hz

• 400V 3 - N ~ 50 Hz

• 400V - 2+2N ~ 50 Hz

Separate the wires and connect them in accordance with

the instructions given in the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

400V - 2+N ~

50 Hz

220-240V 3 ~

50 Hz

400V 3-N ~

50 Hz

: yellow/green;

N: the two blue wires

together

L1: black

L2: brown

400V - 2+2N ~

50 Hz

: yellow/green;

N1: blue

N2: blue

L1: black

L2: brown

Connecting the electricity supply cable to the mains

If the appliance is being connected directly to the

electricity mains an omnipolar switch must be installed

with a minimum opening of 3 mm between contacts.

! The installer must ensure that the correct electrical

connection has been made and that it is fully compliant

with safety regulations.

Before connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is

compliant with the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located

on the appliance itself.

• The voltage falls within the range of values indicated on

the data plate.

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the plug,

ask an authorised technician to replace it. Do not use

extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only.

! The manufacturer declines any liability should these

safety measures not be observed.

! Do not remove or replace the power supply cable for any

reason. Its removal or replacement will void the warranty

and the CE marking. INDESIT does not assume liability

for accidents or damage arising from replacement/

removal of the original power supply cable. Replacement

can only be accepted when carried out by personnel

authorised by INDESIT and using an original spare part.

28

GB

Description of the

appliance

Control panel

The control panel described in this manual is only a representative example: it may not exactly match the panel

on your appliance.

*

Only available in certain models.

ON/OFF indicator light

CONTROLS LOCKED

indicator light

CONTROL PANEL LOCK

button

INCREASE TIME*

button

COOKING ZONE PROGRAMMED*

indicator light

PROGRAMME TIMER*

display

PROGRAMME TIMER

button

DECREASE TIME*

button

POWER and

RESIDUAL HEAT

indicators

ON/OFF button

COOKING ZONE

indicator

TIMER*

indicator light

BOOSTER*

button

BOOSTER*

indicator light

SLIDER ZONE

X

button

EXTENSO TECHNOLOGY

button

EXTENSO TECHNOLOGY

indicator light

• TIMER* indicator light shows that the timer has

been activated

• MAX BUTTON - switches the cooking zone on at

its maximum power level 16 (see Start-up and

use).

• MED BUTTON - switches the cooking zone on at

its medium power level 8 (see Start-up and use).

• MIN BUTTON - switches the cooking zone on at

its minimum power level 1 (see Start-up and use).

• INCREASE TIME* button increases the cooking

duration while the timer is running or while a set

programme is underway

(see Start-up and use).

• DECREASE TIME* button decreases the cooking

duration while the timer is running or while a set

programme is underway

(see Start-up and use).

• EXTENSO TECHNOLOGY button - activates the

EXTENSO TECHNOLOGY mode

• EXTENSO TECHNOLOGY indicator light shows

that the EXTENSO TECHNOLOGY function has

been activated

! This product complies with the requirements of the

latest European Directive on the limitation of power

consumption of the standby mode.

If no operations are carried out for a period of 2

minutes, after the residual heat indicator lights turn

off and the fan stops (if present), the appliance

automatically switches to the “off mode”.

The appliance resumes the operating mode once the

ON/OFF button is pressed.

•

"SLIDER" ZONE -"SLIDER" ZONE -

"SLIDER" ZONE - switches the hotplate on/off or

adjusts its power level (see Start-up and use).

• COOKING ZONE indicator represents the

corresponding cooking zone.

• POWER indicator provides a visual display for the

current heat level.

• ON/OFF button switches the appliance on and off.

• ON/OFF indicator light shows whether the

appliance is on or off.

• PROGRAMME TIMER* button controls the

cooking programme times (

see Start-up and use

).

• PROGRAMME TIMER* display shows which

programme has been selected (

see Start-up and

use

).

• COOKING ZONE PROGRAMMED* indicator lights

show which cooking zones are being used during

a cooking programme (

see Start-up and use

).

• CONTROL PANEL LOCK button prevents

accidental changes to the hob settings (

see

Start-

up and use

).

• CONTROL PANEL LOCK indicator light shows

the control panel has been locked (

see Start-up

and use

).

• BOOSTER* button activates the booster function -

3000 W - of the cooking zone

(see Start-up and

use).

• BOOSTER* indicator light shows that the booster

function has been activated.

29

GB

Start-up and use

! The glue applied on the gaskets leaves traces of grease

on the glass. Before using the appliance, we recommend

you remove these with a special non-abrasive cleaning

product. During the first few hours of use there may be a

smell of rubber which will disappear very quickly.

! A few seconds after the hob is connected to the

electricity supply, a buzzer will sound. The hob may now

be switched on.

Types of noise during normal hob operation:

•

Buzz:Buzz:

Buzz: due to the vibration of the metallic parts that

make up the induction element and the pot; it is

generated by the electromagnetic field required for

heating and increases as the power of the induction

element increases.

•

Soft whistle:Soft whistle:

Soft whistle: heard when the pot placed on the

heating zone is empty; the noise disappears once food

or water is placed into the pot.

•

Crackle:Crackle:

Crackle: produced by the vibration of materials on the

bottom of the pot due to the flow of parasitic currents

caused by electromagnetic fields (induction); can be

more or less intense depending on the material making

up the bottom of the pot, and decreases as the pot

dimensions increase.

•

Loud whistle:Loud whistle:

Loud whistle: heard when two induction elements of

the same group function simultaneously at maximum

power and/or when the booster function is set on the

larger element while the other is auto-adjusted. Noise is

reduced by decreasing the power level of the auto-

adjusted induction element; pot bottom layers made of

different kinds of materials are among the main causes

of this noise.

•

Fan noise:Fan noise:

Fan noise: a fan is necessary to ensure the hob

functions correctly and to safeguard the electronic unit

from possible overheating. The fan functions at

maximum power when the large induction element is at

maximum power or when the booster function is on; in

all other cases, it works at average power depending on

the temperature detected. Furthermore, the fan may

continue to work even after switching the hob off, if the

temperature detected is high.

The types of noise listed above are due to induction

technology and are not necessarily operational faults.

Switching on the hob

To switch the hob on, press and hold the button for

approximately one second.

Switching on the cooking zones

To operate a cooking zone, select the button

corresponding to the desired zone

and set the

required power level by pressing down on the slider

and moving it towards the right to increase the

power level, or towards the left to decrease the

power level.

The min/med/max buttons can also be pressed

directly to select the pre-set power levels: min (1) /

med (8) / max (16), and to switch off the plate (see

below).

MIN/MED/MAX functions

Press the MED button to switch on the cooking zone

at medium power level 8.

Press the MIN button to switch on the cooking zone

at minimum power level 1.

Press the MAX button to switch on the cooking zone

at maximum power level 16.

Booster function*

The booster function for some of the cooking zones may

be used to shorten heating-up times. It may be activated

by pressing the

b

oost er

bb

ooo stost erer

button. The indicator light directly

above the button will illuminate. This function boosts the

power to 2000 W or 3000 W, depending on the size of the

corresponding cooking zone.

It stops automatically after 4 minutes. While the booster for

one of the cooking zones is active, the corresponding front

or rear cooking zone will operate at a reduced power level

(e.g. if the booster for the rear left-hand hotplate has been

activated, the power level of the front left-hand hotplate will

be reduced). For further information, please refer to the

Technical description of the models.

Switching off the cooking zones

To switch off the hotplate, select the button

corresponding to the desired zone, moving the

slider towards the left to return to level 0, or press

the Off button on the slider control directly.

! The first time the slider is pressed, a short beep

will sound to acknowledge the touch. If - and only if -

the power level is adjusted, another short beep will

sound when the slider is released.

! The hotplate selection LEDs light up for the power

adjustment period (10 seconds), during which the

slider (or min/med/max buttons)* can influence the

selected hotplate.

Programming the cooking duration

! If the and buttons are pressed for an extended

period of time, the timer scrolls quickly through the minute

values in the corresponding direction.

! All the cooking zones may be programmed

simultaneously, for a duration between 1 and 99 minutes.

1. Select the cooking zone using the corresponding

selector button.

2. Adjust the power level of the cooking zone.

*

Only available in certain models.

30

GB

3. Press the programming button. The indicator light

corresponding to the selected zone will start flashing.

4. Set the cooking duration using the

--

- and

++

+ buttons.

5. Confirm by pressing the

button or automatic

selection occurs after 10 seconds.

The timer begins counting down immediately. A buzzer

sounds for approximately 1 minute and the cooking zone

switches off when the set programme has finished.

Repeat the above procedure for each hotplate you wish to

programme.

Using multiple programmes and the display

If one or more hotplates are programmed, the display will

show the data for the hotplate with the least time

remaining, and the light corresponding to the position of

the hotplate will flash. The lights corresponding to the other

hotplates programmed will be switched on.

To visualise the time remaining for the other programmed

hotplates, press the

button repeatedly: the time

remaining for each hotplate will be shown sequentially in a

clockwise order, starting from the front left hotplate.

Changing the programme

1. Press the

button repeatedly until

the duration you wish to change is shown.

2. Use the

buttons to set the new duration.

3. Confirm by pressing the

button.

To cancel a programme, follow the above instructions. At

step 2, press the

button: the duration decreases

progressively until it reaches 0 and switches off. The

programme resets and the display exits programming

mode.

Timer

The hob must be switched on.

The timer can be used to set a duration up to 99 minutes.

1. Press the

programming button until the timer

indicator light is illuminated

.

2. Set the desired duration using the

and buttons.

3. Confirm by pressing the

button.

The timer begins counting down immediately. When the

time has elapsed, a buzzer will sound (for one minute).

Control panel lock

When the hob is switched on, it is possible to lock the

oven controls in order to avoid accidental changes being

made to the settings (by children, during cleaning, etc.).

Press the

button to lock the control panel: the

indicator light above the button will switch on.

To use any of the controls (e.g. to stop cooking), you must

switch off this function. Press the

button for a few

moments, the indicator light will switch off and the lock

function will be removed.

Switching off the hob

Press the button to switch off the appliance - do not

rely solely on the pan sensor.

If the control panel lock has been activated, the controls

will continue to be locked even after the hob is switched on

again. In order to switch the hob on again, you must first

remove the lock function.

“Demo” mode

It is possible to set the hob to a demonstration mode

where all the controls work normally but the heating

elements do not switch on. To activate the “demo” mode

the hob must be switched on, with all the hotplates

switched off.

• Press and hold the

++

+ and

--

- buttons simultaneously

for 6 seconds. When the 6 seconds have elapsed, the

ON/OFF and CONTROLS LOCKED indicator lights will

flash for one second. Release the

++

+ and

--

- buttons

and press the

button;

• The display will show the text DE and MO and the hob

will be switched off.

• When the hob is switched on again it will be set to the

“demo” mode.

To exit this mode, follow the procedure described above.

The display will show the text DE and OF and the hob will

be switched off. When it is next switched on, the hob will

function normally.

31

GB

Practical advice on using the appliance

! Use cookware made from materials which are compatible

with the induction principle (ferromagnetic material). We

especially recommend pans made from: cast iron, coated

steel or special stainless steel adapted for induction. Use

a magnet to test the compatibility of the cookware.

*

SUITABLE

UNSUITABLE

Cast iron

Enamelled steel

Special stainless steel

Copper,

Aluminium, Glass, Earthenware,

Ceramic, non magnetic Stainless steel

In addition, to obtain the best results from your hob:

• Use pans with a thick, flat base in order to fully utilise

the cooking zone.

• Always use pans with a diameter which is large enough

to cover the hotplate fully, in order to use all the

available heat.

• Make sure that the base of the cookware is always

clean and dry, in order to fully utilise and extend the life

of both the cooking zones and the cookware.

• Avoid using the same cookware which has been used

on gas burners: the heat concentration on gas burners

may distort the base of the pan, causing it not to adhere

correctly.

Safety devices

Pan sensor

Each cooking zone is equipped with a pan sensor device.

The hotplate only emits heat when a pan with suitable

measurements for the cooking zone is placed on it. If the

power level indicator display flashes, this may be because:

• An incompatible pan

• A pan whose diameter is too small

• The pan has been removed from the hotplate.

Overheating protection

If the electronic elements overheat, the hob switches off

automatically and

F appears on the display, followed by a

flashing number. When the temperature has reached a

suitable level, this message disappears and the hob may

be used again.

Safety switch

The appliance has a safety switch which automatically

switches the cooking zones off after they have been in

operation for a certain amount of time at a particular power

level. When the safety switch has been triggered, the

display shows “

00

0”.

For example: the rear right-hand hotplate is set to 5 and will

switch off after 7 and a half hours of continuous operation,

while the front left-hand hotplate is set to 2 and will switch

off after 9 and a half hours.

Power level

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

Maximum operating time in hours

10

9,5

9

8,5

7,5

7

6,5

6

5,5

5

4

3,5

3

2,5

2

1

Buzzer

This can also indicate several irregularities:

• An object (a pan, cutlery, etc.) has been placed on the

control panel for more than 10 seconds.

• Something has been spilt on the control panel.

• A button has been pressed for too long. All of the

above situations may cause the buzzer to sound.

Remove the cause of the malfunction to stop the

buzzer. If the cause of the problem is not removed, the

buzzer will keep sounding and the hob will switch off.

32

GB

The EXTENSO TECHNOLOGY mode

The EXTENSO TECHNOLOGY can be used to set

the power of two "interconnected" hotplates to the

same level. It can be activated if the two hotplates are

OFF, by pressing the

EXTENSO TECHNOLOGY

button

The

EXTENSO TECHNOLOGY can be activated

while the hob is on by pressing the

EXTENSO

TECHNOLOGY

button once; the LEDs corresponding

to both linked hotplates light up.

The 2 LEDs remain lit as long as the hotplates are

linked (if

EXTENSO TECHNOLOGY button is

pressed again, the hotplates are disconnected and

are both set to power level 0).

Pressing the +, - or Max buttons for one of the two

Flexi hotplates also affects the display corresponding

to the other hotplate.

To deactivate the

EXTENSO TECHNOLOGY , press

the button .

A timer may be set for the

EXTENSO

TECHNOLOGY

; this appears on the display and both

LEDs corresponding to the linked hotplates light up.

When the Timer button is pressed, the two linked

hotplates are treated as if they were a single zone.

Selecting and using

EXTENSO TECHNOLOGY

To begin using the EXTENSO TECHNOLOGY, press

the button. To set the power level (see above).

EXTENSO TECHNOLOGY operation

Once you have selected

EXTENSO TECHNOLOGY

by pressing the button , the 2 LEDs corresponding

to the

EXTENSO TECHNOLOGY for both hotplates

light up; it will then be possible to control both as if

they were a single zone. The power level will appear

on both displays. If only the upper or lower part is in

use, the display corresponding to the unused zone

will begin to flash, and after 3 minutes cooking will

automatically revert to standard mode (not

EXTENSO

TECHNOLOGY

).

! Once activated, the

EXTENSO TECHNOLOGY can

also be programmed, using the same procedure as

described for the individual hotplates.

To exit this mode, follow the procedure described above.

The display will show the text DE and OF and the hob will

be switched off. When it is next switched on, the hob will

function normally.

! Accessories

For optimal

EXTENSO TECHNOLOGY performance,

we recommend the use of pans with an elliptical or

elongated base and a major diameter of at least 250

mm; if using pans with a smaller diameter, we

recommend positioning them in the upper or lower

part as indicated by the X symbol.

If the saucepan is not in the centre of the screen

printing detail, you may hear a whistling sound or a

slight buzzing noise; this does not indicate a hob

malfunction. We recommend adjusting the position

of the pan so that it is in the centre of the EXTENSO

TECHNOLOGY zone

33

GB

Practical cooking advice

Pressure cooking

Pressure cooker

Frying

Grilling Boiling

Very high-flame cookingHigh-flame

cooking

Medium-flame cookingLow-flame

cooking

Very

low-flame

cooking

Crêpes Cooking on a high flame and browning

(roasts, steaks, escalopes, fish fillets, fried

eggs)

Fast thickening (liquid juices)

Boiling water (pasta, rice, vegetables)

Milk

Slow thickening (dense juices)

Bain-marie cooking

Pressure cooking after whistle

Low-flame cooking (stews)

Reheating dishes

Chocolate sauce Keeping food hot

34

GB

Precautions and tips

! This appliance has been designed and manufactured in

compliance with international safety standards. The

following warnings are provided for safety reasons and

must be read carefully.

This appliance conforms to the following European

Economic Community directives:

- 2006/95/EEC dated 12/12/06 (Low Voltage) and

subsequent amendments;

- 2004/108/EEC dated 15/12/04 (Electromagnetic

Compatibility) and subsequent amendments;

- 93/68/EEC dated 22/07/93 and subsequent amendments.

- 1275/2008 stand-by/off mode.

General safety

! Make sure that the air inlet behind the fan grille is never

obstructed. The built-in hob should, in fact, be provided

with suitable ventilation for the cooling of the electronic

components used in the appliance.

! We advise against the installation of an induction hob

above an under-the-counter refrigerator (heat) or above a

washing machine (vibrations). In fact, there would be

insufficient space for the ventilation of electronic

components.

• The appliance was designed for domestic use inside

the home and is not intended for commercial or

industrial use.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

• Do not touch the appliance when barefoot or with wet or

damp hands and feet.

• The appliance must be used by adults only for the

preparation of food, in accordance with the instructions

provided in this booklet. Do not use the hob as a

worktop or chopping board.

• The glass ceramic hob is resistant to mechanical

shocks, but it may crack (or even break) if hit with a

sharp object such as a tool. If this happens, disconnect

the appliance from the electricity mains immediately

and contact a Service Centre.

• Ensure that power supply cables of other electrical

appliances do not come into contact with the hot parts

of the hob.

• Remember that the cooking zones remain relatively hot

for at least thirty minutes after they have been switched

off. An indicator light provides a warning when residual

heat is present (

see Start-up and use

).

• Keep any object which could melt away from the hob,

for example plastic and aluminium objects, or products

with a high sugar content. Be especially careful when

using plastic film and aluminium foil or packaging: if

placed on surfaces which are still hot, they may cause

serious damage to the hob.

• Always make sure that pan handles are turned towards

the centre of the hob in order to avoid accidental burns.

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Never perform any cleaning or maintenance work

without having disconnected the appliance from the

electricity mains.

• The appliance should not be operated by people

(including children) with reduced physical, sensory or

mental capacities, by inexperienced individuals or by

anyone who is not familiar with the product. These

individuals should, at the very least, be supervised by

someone who assumes responsibility for their safety or

receive preliminary instructions relating to the operation

of the appliance.

•

For the attention of wearers of pacemakers orFor the attention of wearers of pacemakers or

For the attention of wearers of pacemakers or

other active implants:other active implants:

other active implants:

The hob complies with all current standards on

electromagnetic interference.

Your induction hob is therefore perfectly in keeping with

legal requirements (89/336/CEE directives). It is

designed not to create interference on any other

electrical apparatus being used on condition that the

apparatus in question also complies with this legislation.

Your induction hob generates short-range magnetic

fields.

To avoid any interference between your induction hob

and a pacemaker, the latter must be designed to

comply with relevant regulations.

In this respect, we can only guarantee our own product

conformity. Please consult the pacemaker manufacturer

or your doctor concerning its conformity or any possible

incompatibility.

• Do not let children play with the appliance.

• Do not place metal objects (knives, spoons, pan lids,

etc.) on the hob as they may become hot..

• The appliance is not intended to be operated by

means of an external timer or separate remote-

control system.

Disposal

• When disposing of packaging material: observe local

legislation so that the packaging may be reused.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using

the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials

inside the machine, while preventing potential damage

to the atmosphere and to public health. The crossed-out

dustbin is marked on all products to remind the owner

of their obligations regarding separated waste

collection.

For further information relating to the correct disposal of

exhausted household appliances, owners may contact

the public service provided or their local dealer.

35

GB

Care and maintenance

Switching the appliance off

Disconnect your appliance from the electricity

supply before carrying out any work on it.

Cleaning the appliance

! Do not use abrasive or corrosive detergents (for

example, products in spray cans for cleaning

barbecues and ovens), stain removers, anti-rust

products, powder detergents or sponges with

abrasive surfaces: these may scratch the surface

beyond repair.

! Never use steam cleaners or pressure cleaners on

the appliance.

• It is usually sufficient simply to wash the hob

using a damp sponge and dry it with absorbent

kitchen towel.

• If the hob is particularly dirty, rub it with a special

glass ceramic cleaning product, then rinse well

and dry thoroughly.

• To remove more stubborn dirt, use the scraper

provided. Remove spills as soon as possible,

without waiting for the appliance to cool, to avoid

residues forming crusty deposits. You can obtain

excellent results by using a rust-proof steel wire

sponge - specifically designed for glass ceramic

surfaces - soaked in soapy water.

! The scraper provided is sharp: be careful when

using it.

• If any plastic or sugary substances are

accidentally melted on the hob, remove them

immediately with the scraper, while the surface is

still hot.

• Once it is clean, the hob may be treated with a

special protective maintenance product: the

invisible film left by this product protects the

surface from drips during cooking. This

maintenance task should be carried out while the

appliance is warm (not hot) or cold.

• Always remember to rinse the appliance well with

clean water and dry it thoroughly: residues can

become encrusted during subsequent cooking

processes.

Stainless steel frame (only in models with outer

frame)

Stainless steel can be marked by hard water which

has been left on the surface for a long time, or by

cleaning products containing phosphorus.

After cleaning, it is advisable to rinse the surface

well and dry it thoroughly. If water is spilt on the

surface, dry it quickly and thoroughly.

! Some hobs have an aluminium frame which is

similar to stainless steel. Do not use any cleaning or

degreasing products which are not suitable for use

with aluminium.

Disassembling the hob

If it is necessary to disassemble the hob:

1. Loosen the screws fixing the alignment springs on

each side.

2. Loosen the screws holding the fixing hooks in

each corner.

3. Take the hob out of its installation cavity.

! Do not attempt to repair the appliance yourself. If

the appliance breaks down, contact a Service

Centre.

36

GB

Technical description of

the models

The induction system is the quickest existing way of cooking. Unlike traditional hotplates where the cooking

zone heats up, with the induction system heat is generated directly inside pans which have ferromagnetic

bases.

Key:

I = single induction cooking zone

B = booster: the power of the cooking zone may be boosted to 3000 W

* = the maximum power level is limited while the booster is activated for the relevant rear cooking zone

(see

Start-up and use).

Hobs

TIS 621 CT L

Cooking zone

Power (W)

Back Left

I 1400

Back Right

I 3000 – B 4000

Front Left

I 1400

Total power

6800

Page is loading ...

Scholtes TIS 621 CT L Owner's manual

Scholtes TIS 621 CT L Owner's manual

in other languages

Related papers

Other documents