Baby Lock Coronet Longarm User guide

Baby Lock Coronet User Manual | 1

Table of Contents

How to Use This Manual............................................................................................................................ 2

Federal Communicaons Commissions (FCC) Declaraon of Conformity (For USA Only) ..................... 3

Canadian Department of Communicaons Compliance Statement (For Canada Only) .........................3

Radio Interference (Other than USA and Canada) ............................................................................... 3

Important Safety Informaon (English) ...............................................................................................4

Package Contents/Included Accessories .................................................................................................... 7

Oponal Accessories .................................................................................................................................. 8

About Your Machine ........................................................................................................................... 9

General Specicaons ................................................................................................................................ 9

Get to Know Your Baby Lock Coronet ....................................................................................................... 10

Installaon and Setup ....................................................................................................................... 13

Carriage .................................................................................................................................................... 13

Power Cord ............................................................................................................................................... 14

Handlebars and Display ............................................................................................................................ 14

Oponal Accessory: Rear Handlebars and Display ................................................................................... 15

Thread Antennae ...................................................................................................................................... 16

Oponal Accessory: Horizontal Spool Pin ................................................................................................ 17

Oponal Accessory: Ruler Base ................................................................................................................ 18

Oponal Accessory: Laser Light Stylus ..................................................................................................... 19

Using Your Machine .......................................................................................................................... 21

Power Switch ............................................................................................................................................ 21

Lighng ..................................................................................................................................................... 21

Machine Needle ....................................................................................................................................... 21

Hopping Feet ............................................................................................................................................ 23

Oponal Accessories: Couching Feet and Glide Foot ............................................................................... 24

Bobbin and Bobbin Tension ...................................................................................................................... 24

Top Thread Tension .................................................................................................................................. 26

Oponal Accessory: Quick-Set Tension Kit ............................................................................................... 27

Threading the Machine ............................................................................................................................ 28

Quilng With the Baby Lock Coronet ................................................................................................ 30

Preparing to Quilt ..................................................................................................................................... 30

Oponal Computer-Guided Quilng: Pro-Stcher® ................................................................................. 31

Using the Touch-Screen Display ........................................................................................................ 32

Overview of the Main Screen ................................................................................................................... 32

Stching Modes ........................................................................................................................................ 34

Controlling the Lights ............................................................................................................................... 38

2 | www.babylock.com

Machine Tools .................................................................................................................................. 39

On-screen Calculator ................................................................................................................................ 39

Diagnoscs ............................................................................................................................................... 40

Alarms ...................................................................................................................................................... 42

Quilt Timer and Stch Counter ................................................................................................................. 43

Set Language ............................................................................................................................................ 45

Updang Machine Soware ..................................................................................................................... 45

Informaon Screen ........................................................................................................................... 48

Machine Maintenance ...................................................................................................................... 49

Clean and Oil Your Baby Lock Coronet ..................................................................................................... 49

Maintenance Schedule ............................................................................................................................. 50

Troubleshoong ............................................................................................................................... 51

Oponal Accessories ........................................................................................................................ 56

How to Use This Manual

Notes, Important Notes, and Cauons

 NOTE: A NOTE indicates important informaon that helps you make beer use of your

Baby Lock product.

Â IMPORTANT: An IMPORTANT note provides informaon that is essenal to properly using your

Baby Lock product.

U CAUTION: A CAUTION indicates a potenal for causing harm to your quilng machine, the quilt,

or to yourself.

Baby Lock Coronet User Manual | 3

Federal Communicaons Commissions (FCC) Declaraon of Conformity

(For USA Only)

Responsible Party: Tacony Corporaon

Corporate Center

1760 Gilsinn Lane

Fenton, MO 63026-0730 USA

declares that the product

Product Name: Baby Lock Coronet

complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operaon.

This equipment has been tested and found to comply with the limits for Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful

interference in a residenal installaon. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instrucons, may cause harmful interference

to radio communicaons. However, there is no guarantee that interference will not occur in a parcular

installaon.

If this equipment does cause harmful interference to radio or television recepon, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modicaons not expressly approved by the manufacturer or local sales distributor could void

the user’s authority to operate the equipment.

Canadian Department of Communicaons Compliance Statement (For Canada Only)

This digital apparatus does not exceed the Class B limits for radio noise emission from digital apparatus

as set out in the interference-causing equipment standard entled “Digital Apparatus”, ICES-003 of the

Department of Communicaons.

Radio Interference (Other than USA and Canada)

This machine complies with EN55022 (CISPR Publicaon 22) /Class B and AUS/NZ 55022/Class B.

4 | www.babylock.com

Important Safety Information

This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operaon. See the full Declaraon of Conformity

in the Appendix.

Â IMPORTANT: Do not operate your Baby Lock Coronet quilng machine unl you have completely

read the informaon contained in this manual. Please keep all packaging and order informaon for

warranty purposes.

IMPORTANT SAFETY INSTRUCTIONS

Read all instrucons before using this machine.

When using this machine, basic safety precauons should always be followed, including the following:

DANGER — To reduce the risk of electric shock:

• A quilng machine should never be le unaended when plugged in. Always unplug the machine

from the electrical outlet immediately aer using and before cleaning.

WARNING — To reduce the risk of burns, re, electric shock, or injury to persons:

• The Baby Lock Coronet is heavy. Never aempt to li it alone. Always use two people when liing.

Always li from the throat of the machine, not from the handlebars.

• Always unplug the Baby Lock Coronet from the electrical outlet when performing any maintenance,

changing the needle, removing thread locks, or when le unaended.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Keep ngers away from all moving parts. Use cauon around the needle or sharp external

components.

• Change the needle oen. Do not use bent or dull needles. “Every quilt deserves a new needle”.

• Switch the machine to the symbol o, or 0, posion to turn it o when making any adjustments in

the needle area, such as threading needle, changing needle, threading bobbin, changing hopping

foot, and so forth.

• Never drop or insert foreign objects into any opening.

• The Baby Lock Coronet should only be used indoors away from moisture.

• The Baby Lock Coronet should not be stored or used in extreme temperatures.

• Use the Baby Lock Coronet only for its intended use as described in this manual.

• To disconnect from the wall outlet, push the switch to the o posion, then remove the plug

from outlet pulling from the plug, not the cord. Never operate the Baby Lock Coronet if the cord

is damaged or not working correctly. If a mechanical or electrical problem is encountered, return

the Baby Lock Coronet to your authorized Baby Lock retailer for examinaon, repair, electrical or

mechanical adjustment.

• It is not recommended that the Baby Lock Coronet quilng machine be used with any machine

quilng frame other than those recommended by Baby Lock.

Baby Lock Coronet User Manual | 5

• Use this quilng machine only for its intended use as described in this manual. Use only

recommended aachments as contained in this manual.

• Never operate the machine with any air openings blocked. Keep venlaon openings of the

machine free from the accumulaon of lint, dust, and loose cloth.

• Do not operate where aerosol (spray) products are being used or where oxygen is

being administered.

• Do not pull or push the machine across the fabric excessively while stching. It may deect the

needle enough to cause it to break.

• Use only needles designed for free moon quilng and recommended by Baby Lock for this

machine. Other types of needles may break during normal quilng.

• Children shall not play with the machine. Close aenon is necessary when this machine is used by

or near children.

• This sewing machine may be used by children age 8 years and above and persons with reduced

physical, sensory, or mental capabilies or lack of experience and knowledge, if they are instructed

concerning the safe use of the machine, understand the hazards involved, and are supervised.

• Cleaning and user maintenance shall not be made by children without supervision.

Save these instrucons.

This machine is intended for household or commercial use.

Disclaimer

Baby Lock and its authorized retailers are not legally responsible or liable for damage to the Baby Lock

Coronet when used improperly or not in accordance with the guidelines stated in this manual or when

used on Home Machine Quilng Frames not recommended by Baby Lock.

For addional product informaon, visit our website at: www.babylock.com.

To use the machine safely

1. Carefully watch the needle when sewing. Do not touch the handwheel, take up lever, needle, or other

moving parts.

2. Turn the machine o and unplug the cord in the following cases:

• when you have stopped using the machine

• when you replace or remove the needle or any other part

• when you check or clean the machine

• when you leave the machine unaended

3. Connect the machine directly to the wall outlet or to a surge protector that connects directly to the

wall outlet. Do not use extension cords.

6 | www.babylock.com

To increase the life of your machine

1. Do not store this machine in areas exposed to direct sunlight or high humidity. Never use or store

the machine near a heater, an iron, a halogen lamp or other hot things.

2. Use only neutral soaps or detergents to clean the machine. Benzene, solvents and scouring powders

can damage the case and the machine and therefore should never be used.

3. Do not drop or bump the machine.

4. Always consult the manual to replace or x the hopping foot, needle or any other part of the

machine.

Oponal U.S. Grounding for Customers with 120 VAC Connecons

GROUNDED OUTLET BOXES

METAL

SCREW

ADAPTER

(B)

(C)

TAB FOR

GROUNDING

SCREW

(A)

GROUNDING PIN

This product is for use on a nominal 120 V or nominal 220 V circuit, and has a grounding plug that looks

like the plug illustrated in sketch A above. A temporary adapter, which looks like the adapter illustrated in

sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in sketch C if a properly

grounded outlet is not available. The temporary adapter should be used only unl a properly grounded

outlet can be installed by a qualied electrician. The green colored rigid ear, lug, and the like, extending

from the adapter, must be connected to a permanent ground such as a properly grounded outlet box cover.

Whenever the adapter is used, it must be held in place by the metal screw.

Â IMPORTANT: In Canada, the use of a temporary adapter is not permied by the

Canadian Electric Code.

To repair or adjust the machine

If the machine does not funcon properly or needs adjustment, rst check the troubleshoong chart in the

appendix to inspect and adjust the machine yourself. If further assistance is required, please contact your

closest authorized Baby Lock retailer.

For more product informaon and updates, visit our website at www.babylock.com.

The contents of this manual and product specicaons are subject to change without prior noce.

Baby Lock Coronet User Manual | 7

Package Contents/Included Accessories

Part name Part Code

Baby Lock Coronet Quilng Machine BLCT16A

Carriage QF09517

Front Handlebars and Display QM29452

Ribbon Cable QM20791

Bobbin Winder BLQBW

Lint brush JW010270

Class M Bobbins (5 pieces: one in the bobbin case, four in accessory box) BLJ-BOB (3 pkg)

Needle (134 MR) size 16 (pack of 10) 134FG-100

Needle (134 MR) size 18 (pack of 10) 134FG-110

Bobbin Case (in the machine) JW000586

Thread Antennae JW010214

Oiler JW010272

Screwdriver (bobbin case) JW010269

Power Cord JW020277

2.5 mm Allen wrench QM10286

4 mm Allen wrench QM10288

8 mm open wrench QM40235

Hopping foot (installed on machine) QM10511

Open-toe hopping foot QM10510

Quick Reference Card QM30278

Instrucon and Reference Guide IBBLCT16A

8 | www.babylock.com

Optional Accessories

Oponal Accessories for Coronet Machine

Part Name Part Code

Coronet Rear Handlebars and Display BLCT16-RH Shown on pages 16 and 56

Coronet Ruler Base BLCT16-RB Shown on pages 19 and 56

Quick-Set Tension BLQ-QST Shown on pages 27 and 56

Couching Foot Set BLQ-CCF Shown on pages 25 and 56

Glide Foot BLQ-GF Shown on pages 25 and 57

Horizontal Spool Pin BLJ18-HS Shown on pages 18 and 57

Channel Lock BLJ18-CL Shown on page 57

Laser Light Stylus BLCT16-LL Shown on pages 20 and 57

Stylus Adapter Plate and Holder BLJ18-SA Shown on page 58

Stylus BLJ18-ST Shown on page 58

Needle (134 MR) Size 12 (pack of 10) 134FG-80 Not shown

Needle (134 MR) Size 14 (pack of 10) 134FG-90 Not shown

Needle (134 MR) Size 20 (pack of 10) 134FG-125 Not shown

Pro-Stcher 3

(Recommended for use on Pearl Frame)

BLPS3 Shown on pages 31 and 58

Oponal Accessories for Coronet Frame

Part Name Part Code

Easy-Grasp Quilt Clamps (set of 2) BLQ-EQC Shown on page 58

Deluxe Quilt Clamp BLQ-DQC Shown on page 58

2-inch Quilt Clamp (small, set of 2) BLQ-SQC Shown on page 59

3-inch Quilt Clamp (large, set of 2) BLQ-LQC Shown on page 59

Bungee Clamps (set of 4) BLQ-BC Not shown

Casters (package of 2) BLQ-CASTER Shown on page 59

Baby Lock Coronet User Manual | 9

About Your Machine

General Specicaons

The Baby Lock Coronet uses high-tech electronics and an innovave touch-screen user interface to oer

greater funconality and ease of operaon to home quilters than ever before conceived in the quilng

industry. The Baby Lock Coronet quilng machine is a high quality machine that both incorporates robust

design features and is easy to service.

Sewing Opening Dimensions 8.25 inches X 16 inches (245 mm X 610 mm)

Sewing Speed Manual Mode: from 25 stches per minute to 1800 stches per minute

Regulated Mode: from 0 stches per minute to full speed

Stches Per Inch 4 stches per inch to 18 stches per inch

Needle System 134 (135 X 7)

Needle Sizes (recommended) From 12/80 to 20/125

Hook System Rotary, Horizontal Axis, M-class bobbin

Bobbin Type Aluminum, Class M

Bobbin Case Type MF

Motor Type Brushless DC

Needle Posioning Up and down, walking stch

Electrical Power

US/Canada:

Rest of world*:

105 – 120 VAC, 47-63Hz, 600W peak

100 – 250 VAC, 47-63Hz, 600W peak

* Complies with internaonal standards

Sew Foot Stroke/Li 5 mm

Needle Bar Stroke 35.3 mm

Take-Up Stroke 73 mm

Lubricaon, main components Kluber Lube, permanent

Lubricaon of hook Velocite 10, Texaco 22

10 | www.babylock.com

Get to Know Your Baby Lock Coronet

Right side view

1. Thread Antennae

2. Thread Guide A

3. Three-Hole Thread Guide B

4. Thread Guide C

5. Top Thread Tension Assembly

6. Srrup Thread Guide E

7. Take-Up Lever

8. Thread Guide F

9. Front Casing/Frame

10. Handwheel

11. Side Laser Stylus Post Hole

9

5

4

8

6

3

7

1

2

10

11

Baby Lock Coronet User Manual | 11

12. Needle Bar

13. Needle Bar Thread Guide

14. Needle

15. Ruler Foot

16. Needle Plate

17. Mount

18. Presser Bar

Le side view

19. Front Threaded Display Mounng Holes

20. Front Base

21. Back Casing/Frame

22. Rear Base

23. Color Touch-Screen Display USB Connector

24. Threaded Horizontal Spool Pin Mounng Hole

25. Needle Bar Clamp Screw

26. Machine Stch Regulator (Y-Moon)

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

DETAIL A

12 | www.babylock.com

Rear and Front Views

27. On/O Switch

28. Power Cord Connector

29. Accessory Power Outlet

30. Serial Port for Stch Regulator

31. Laser Light Stylus Power Connector

32. Rear Handlebar USB Connector

33. Rear Threaded Handle Holes

34. Spool Pin 1

35. Electronic Control Pod (C-Pod)

36. Bobbin Assembly

37. LED Light Ring

38. Power Pod (P-Pod)

39. Spool Pin 2

Rear

Front

29

28

27

38

30

39

35

34

37

36

33

31

32

Baby Lock Coronet User Manual | 13

Rear and Front Views

27. On/O Switch

28. Power Cord Connector

29. Accessory Power Outlet

30. Serial Port for Stch Regulator

31. Laser Light Stylus Power Connector

32. Rear Handlebar USB Connector

33. Rear Threaded Handle Holes

34. Spool Pin 1

35. Electronic Control Pod (C-Pod)

36. Bobbin Assembly

37. LED Light Ring

38. Power Pod (P-Pod)

39. Spool Pin 2

Rear

Front

29

28

27

38

30

39

35

34

37

36

33

31

32

Installation and Setup

Carriage

You should have already set up the Coronet Frame. Refer to the frame manual for detailed instrucons

about seng up the frame.

To install the carriage and machine on the frame

1. Place the carriage on the table rails, ensuring

that the stch regulator faces the back of the

frame.

2. Place the machine on the carriage.

U CAUTION: The Baby Lock Coronet is heavy.

Never aempt to li it alone. Always use

two people when liing. Always li from

the throat of the machine, not from the

handlebars or needle bar.

3. Plug the ribbon cable from the stch regulator

connector at the back of the machine (see Rear

View on the previous page, #30) into the stch

regulator on the carriage.

Â IMPORTANT: If you ever need to remove the machine from the carriage, disconnect the ribbon

cable from the stch regulator at the back of the carriage. Failure to unplug the cable when

removing the machine from the carriage could result in damage to the cable, encoders, and

carriage.

Â IMPORTANT: The connector is keyed to ensure correct alignment. Make sure the keyed poron of

the cable connector aligns with the keyed poron of the encoder connector. Do not force.

14 | www.babylock.com

Power Cord

To install the power cord

• Insert the cord into the power connector on the rear of the machine. Secure the cord with the

metal clip. Plug the three-prong end into power source. Do not turn on the machine unl the front

handlebars and display are installed.

To disconnect the power cord

• Unplug the cord from the power outlet. Release the metal clip where the cord connects with the

machine and then pull out the cord.

For more informaon, see Power Switch in the Using Your Machine secon of this manual.

 NOTE: Make sure that the machine is o before plugging into power source. The rear power switch

should be in the 0, or o, posion.

Handlebars and Display

U CAUTION: To prevent any electrical damage to the handlebars, always turn o all power to the

machine when connecng or disconnecng the handlebars.

To install the handlebars

1. Ensure that the machine is unplugged from the electrical outlet.

2. Locate the three long buon head screws and

the 4 mm Allen wrench. Line up the holes on

top of the handles with the pre-drilled holes on

top of the machine.

3. Slide a single screw into one of the holes unl

it stops. Hand ghten the bolt enough to secure

the handles to the top of the machine. Insert

and hand-ghten the remaining two

handlebar bolts.

4. Use the included 4 mm Allen wrench to securely

fasten the handles to the front of the machine.

Baby Lock Coronet User Manual | 15

5. Aer the bolts are in place, plug the cable into

the USB-style connecon located on the front-

le side of the machine.

6. Remove the protecve plasc from the touch-screen display before using.

To use the handlebar buons

Press the Up/Down

buon to cycle the

needle a half stch.

Press the Start/Stop

buon to start or stop

the machine from

stching.

Press the Speed Up or Speed Down buons to change the

stches per minute seng (manual mode) or stches per

inch (regulated mode).

Oponal Accessory: Rear Handlebars and Display

To install the oponal rear handlebars and display

Â IMPORTANT: Install the rear handlebars

and display aer the front handlebars and

display have been installed.

1. Check that the machine is unplugged from the

electrical outlet.

U CAUTION: All power to the machine must

be turned o when installing the rear

handlebars. Failure to do so can result in

damage to the machine.

2. The rear handlebars come mounted to a bracket. Line up the two holes in the bracket with those on

the rear of the machine.

16 | www.babylock.com

3. Slide the two bolts into holes unl they stop. Hand ghten, and then use the 4 mm wrench to securely

fasten the handles to the back of the machine.

4. Aer the two bolts are in place, plug the small connector end of the cable into the port on the le side

of the display. Push the plug securely into place.

5. Securely plug the other end of the cable into the port on the back of the machine below

the handlebars.

 NOTE: See the instrucons that accompany the Rear Handlebars and Display.

Â IMPORTANT: Aer the rear handlebars have been completely installed and plugged in, test them by

turning on the Baby Lock Coronet and looking at the rear display. If nothing appears on the screen,

check that both the front and rear handlebar cables are plugged in securely, that your machine is

turned on, and that the power cord is plugged into the machine as well as a power source.

Thread Antennae

To install the thread antennae

1. Locate the threaded hole on top of the machine by

the handwheel.

2. The thread antennae comes with a washer and a

nut. Remove the nut and washer, replace the nut

onto the antennae for two or three turns.

3. Place the washer on the hole and insert the thread

antennae. The washer protects the painted surface

when the nut is ghtened.

4. Turn the thread antennae clockwise several

revoluons, stopping when the antennae eyelets are

posioned directly over the spool pins.

5. Tighten the nut to secure the antennae to the

machine.

Baby Lock Coronet User Manual | 17

Oponal Accessory: Horizontal Spool Pin

An oponal horizontal spool pin is available for metallic and specialty threads wound on a spool

(not a cone).

To install the oponal horizontal spool pin

1. Remove the nut and washer from the post.

Place washer over the threaded hole on the top

of machine.

2. Replace nut and screw the post into the

threaded hole. Tighten the nut to secure.

3. Place the clamp on the post and place

remaining pin in the clamp. Tighten the screw

to hold in place.

4. Elevate the end of the pin slightly above horizontal to keep spool from falling o.

5. Thread the machine beginning at horizontal spool pin, bypassing the thread antenna. When using

delicate threads with the Horizontal Spool Pin, skip thread guide A. Thread the top hole only of the

three-hole thread guide B, back to front. (See Right side view, items 2 and 3.)

6. Connue threading the machine as described in steps 3 through 6 in the secon named Threading

Your Machine later in this manual.

18 | www.babylock.com

Oponal Accessory: Ruler Base

If you plan to use rulers and templates with the Baby Lock Coronet, you need to purchase the ruler base to

give you a large, stable surface on which to rest the ruler or template. The ruler base, rulers, and templates

are oponal accessories. Please see your authorized Baby Lock retailer.

To install the oponal ruler base

1. Starng with the le side, place the ruler base at an angle

so that the le holes on the base t onto the notches on

the machine.

2. Lightly ex the right side of the ruler base so that it falls

into place.

To remove the ruler base

• Start by lightly liing the right side of the ruler base o of

the notches on the machine; then remove the le side.

To use rulers and templates with your quilng machine

U CAUTION: Use only one-quarter inch thick rulers and templates with your machine. Do not use

rotary-cung rulers as they are too thin and can easily slip under the hopping foot. Always use a

ruler base or extended table to stabilize the ruler.

Keep the ruler at and quilt only where you are securely holding the ruler. Avoid losing control by walking

your hand along the ruler or stopping and reposioning your hand and the ruler.

• Apply gentle three-point pressure to the ruler, as follows.

1. Press the ruler against any side of the hopping foot.

2. Press machine against ruler.

3. Press ruler against ruler base with only as much pressure as is necessary to keep the ruler from

slipping. Too much pressure will keep the machine from moving.

The machine’s hopping foot stches a quilng line that is a quarter inch away from the ruler edge. The

markings on all Baby Lock rulers take this into consideraon.

 NOTE: Set the machine to stop in the needle-down posion to keep the machine from moving while

making adjustments with the ruler.

Page is loading ...

Baby Lock Coronet Longarm User guide

Baby Lock Coronet Longarm User guide

Related papers

Other documents