Stratasys Objet350 User manual

DOC-17001 Rev.G

3D Printing System

User Guide

Objet350

Copyright

This documentation contains proprietary information of Stratasys Ltd. This information is supplied solely to assist authorized

users of Objet350 3D printing systems. No part of this document may be used for other purposes, and it may not be disclosed to

other parties.

The specifications on which this document is based are subject to change without notice.

Trademarks

The following are registered trademarks of Stratasys Ltd.: Stratasys

®

, Objet

®

, FullCure

®

.

The following are trademarks of Stratasys Ltd.: Connex, , PolyJet, Objet Studio, Job Manager.

Microsoft and Windows XP are trademarks of Microsoft Corporation.

All names of products and services cited in this book are trademarks or registered trademarks of their respective companies.

FCC Compliance

The equipment referred to in this guide has been tested and found to comply with the limits for a Class A device pursuant to

part 15 of the FCC rules. These limits provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. Stratasys 3D printing systems generate, use and can radiate radio-frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the

user will be required to correct the interference at his own expense.

The 3D printer referred to in this guide contains a transmitter module, FCC ID YH6-MATCAB.

NOTE: Stratasys is not responsible for radio or TV interference caused by unauthorized modification to this equipment.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Equipment Recycling

In the European Union, this symbol indicates that when the last user wishes to discard a product, it must be sent to appropriate

facilities for recovery and recycling. For information about proper disposal, check your purchase contract, or contact the

supplier of the equipment.

Limitation of Liability

The product, software or services are being provided on an “as is” and “as available” basis. Except as may be stated

specifically in your contract, Stratasys Ltd. expressly disclaims all warranties of any kind, whether express or implied,

including, but not limited to, any implied warranties of merchantability, fitness for a particular purpose and non-infringement.

You understand and agree that Stratasys Ltd. shall not be liable for any direct, indirect, incidental, special, consequential or

exemplary damages, including but not limited to, damages for loss of profits, goodwill, use, data or other intangible losses (even

if Stratasys has been advised of the possibility of such damages), resulting from: (i) the use or the inability to use the product or

software; (ii) the cost of procurement of substitute goods and services resulting from any products, goods, data, software,

information or services purchased; (iii) unauthorized access to or alteration of your products, software or data; (iv) statements

or conduct of any third party; (v) any other matter relating to the product, software, or services.

The text and drawings herein are for illustration and reference only. The specifications on which they are based are subject to

change. Stratasys Ltd. may, at any time and without notice, make changes to this document. Stratasys Ltd., for itself and on

behalf of its subsidiaries, assumes no liability for technical or editorial errors or omissions made herein, and shall not be liable

for incidental, consequential, indirect, or special damages, including, without limitation, loss of use, loss or alteration of data,

delays, or lost profits or savings arising from the use of this document.

DOC-17001 Rev.G

Patents

This product is covered by one or more of the following U.S. patents:

5,386,500

6,259,962

6,569,373

6,658,314

6,850,334

7,183,335

7,209,797

7,225,045

7,364,686

7,369,915

7,479,510

7,500,846

7,604,768

7,628,857

7,658,976

7,725,209



Stratasys Ltd.

http://www.stratasys.com



DOC-17001

Revision G

June 2016

DOC-17001 Rev.G

Contents

1 AboutThisGuide

UsingThisGuide 1-2

ForMoreInformation 1-2

TermsUsedinThisGuide 1-3

2 Safety

SafetyFeatures 2-2

SymbolsandWarningLabels 2-3

SafetyGuidelines 2-4

PrinterInstallation 2-4

PrinterOperation 2-4

UVRadiation 2-5

PrinterMaintenance 2-5

ModelandSupportMaterials 2-5

UVLamps 2-6

FirstAidforWorkingwithPrintingMaterials 2-7

ContactwithSkin 2-7

ContactwithEyes 2-7

Ingestion 2-7

Inhalation 2-8

WasteDisposal 2-8

3 IntroducingtheObjet3503DPrintingSystem

WelcometoConnex™Printing 3-2

WorkConfigurations 3-3

SourceFiles 3-4

STLFiles 3-4

SLCFiles 3-4

VRMLFiles 3-4

Workflows 3-5

PrintingMaterials 3-6

Storage 3-6

ShelfLife 3-6

ExposuretoLight 3-6

SafetyConsiderations 3-7

Disposal 3-7

WorkEnvironment 3-7

WorkstationRequirements 3-7

PreparingFilesforUsewithPolyJet3DPrintingSystems 3-8

ConvertingCADFilestoSTLFormat 3-8

ConvertingCADFilestoWRLFormat(VRML) 3-8

ConvertingCADFilestoSLCFormat 3-8

ObjetStudioSoftware 3-9

4 InstallingObjetStudio

HowtoInstallObjetStudio 4-2

DOC-17001 Rev.G iii

5 UsingObjetStudio

LaunchingObjetStudio 5-4

Windows®7SecurityWarning 5-4

ObjetStudioInterface 5-6

RibbonCommands 5-8

ObjetStudioCommandsMenu 5-10

ModelTreePane 5-10

AssigningPropertiestoHiddenObjects 5-11

PreparingModelsforProduction 5-12

OBJDFFiles:Overview 5-12

ModelFiles 5-12

PlacingObjectsontheBuildTray 5-13

OpeningObjetTrayFiles 5-18

Quick-AccessModelCommands 5-20

SelectingObjects 5-21

CopyingandPastingObjects 5-21

SurfaceFinish 5-23

SplittingObjectsintoComponents 5-23

Model-MaterialSettings 5-24

ChangingtheModelMaterial 5-26

ChangingtheSupportMaterial 5-26

DigitalMaterials 5-27

AssigningaModelMaterialtoObjects 5-28

CoatingObjects 5-29

PositioningObjectsontheBuildTray 5-30

AutomaticOrientation 5-30

AutomaticPositioning 5-32

ManualPositioning 5-33

ManipulatingObjectsontheTray 5-35

PositioningObjectsontheZ-Axis 5-35

ValidObjectPlacement 5-36

UsingaGridtoPositionObjects 5-37

MeasurementUnits 5-38

SettingModelDimensions 5-39

RepositioningObjects 5-39

ChanginganObject’sOrientation 5-41

GroupingandUngroupingObjects 5-44

FreezingModelOrientation 5-45

DisplayOptions 5-46

ViewingObjects 5-46

ScreenLayout 5-48

TrayPerspective 5-49

SettingObjectColors 5-51

LoadingLargeFiles 5-51

LargeFileManipulation 5-52

ZoomOptions 5-54

HandlingTrays 5-55

TrayValidation 5-55

ProductionEstimates 5-56

PrintingModes 5-57

E-mailingObjetDigitalFiles 5-58

PrintingtheTray 5-58

DOC-17001 Rev.G iv

ApplyingAdditionalObjetStudioFeatures 5-62

DividingObjects 5-62

ChoosingtheSupportStrength 5-63

“Hollow”—FillingModelswithSupportMaterial 5-64

DisplayingtheCrossSectionofObjects 5-65

SavingtheScreenDisplayasanImageFile 5-66

SavingandImportingBuildTrays 5-67

OBJTFFiles 5-67

OBJZFFiles 5-67

CustomizingObjetStudio 5-68

CreatingaQuickAccessToolbar 5-68

HidingtheRibbon 5-70

DisplayColors 5-70

KeyboardShortcuts 5-72

SettingUserPreferences 5-74

ProfessionalModeFeatures 5-75

DefaultSettings 5-76

OpenGLDriverConfiguration 5-77

GettingAdditionalObjetStudioAssistance 5-79

ObjetStudioVersion,MaterialModuleandLicensedFeatures 5-79

MonitoringandManagingPrintJobs 5-82

JobManagerScreen 5-83

SettingthePrinterConnection 5-85

Off-lineMode 5-86

SettingtheRemotePrinterConnection(ClientMode) 5-89

JobManagerCommands 5-89

ConfiguringUserAlerts 5-92

PrintingfromtheJobsQueue 5-93

AdditionalServerFeatures 5-94

6 OperatingandMaintainingtheObjet3503DPrinter

StartingthePrinter 6-3

LoadingModelandSupportCartridges 6-5

ProducingModels 6-6

PreparingthePrinter 6-6

PrinterInterfaceColorKey 6-8

PrintingIndicators 6-9

ResumingProductionAfterPrintinghasStopped 6-10

ChangingthePrintingMaterial 6-12

AdditionalStepsforPrintingWithBio-CompatibleMaterials 6-16

AdvancedSettings 6-16

KeepingthePrinterinIdleMode 6-19

ShuttingDownthePrinter 6-20

ShutdownWizard 6-21

MaintainingthePrinter 6-23

RoutineMaintenanceSchedule 6-23

MaintenanceCounters 6-24

UVLampCheck 6-26

CleaningthePrintHeadsandtheRoller 6-26

CleaningandReplacingtheWiper 6-29

PatternTest 6-32

ImprovingPrintQuality 6-33

DOC-17001 Rev.G v

CleaningtheRollerWasteCollectorandInspectingtheRollerScraper 6-34

ReplacingtheRollerScraper 6-37

AligningthePrintHeads 6-39

Optimizing(Calibrating)PrintHeads 6-43

ReplacingPrintHeads 6-50

TestingandCalibratingtheUVLamps 6-61

CalibratingtheLoadCells 6-69

ReplacingtheOdorFilter 6-70

ReplacingtheUVLamps 6-71

Built-inTests 6-77

ReplacingtheWasteContainer 6-84

CleaningtheExteriorPanels 6-86

7 HandlingPrintedModels

RemovingModelsAfterPrinting 7-2

RemovingtheSupportMaterial 7-2

Post-PrintingTreatmentforModelsMadewithVeroClear 7-4

Photo-BleachingInstructions 7-5

StoringModels 7-5

DOC-17001 Rev.G vi

DOC-17001 Rev.G 1-1

1

About This Guide

UsingThisGuide 1-2

ForMoreInformation 1-2

TermsUsedinThisGuide 1-3

Objet350 User Guide 1 About This Guide

DOC-17001 Rev.G 1-2

Using This Guide

Thisuserguideprovidesinstructionsforinstalling,operatingandmaintaining

Objet3503Dprintingsystems.Itexplainshowtousefeatures,andprovides

practicalexamplestoguideyouasyouusethesystem.

ThetextandfiguresinthisguidearebasedontheObjet3503Dprinter,

printersoftwareversion38.2andObjetStudiosoftwareversion9.2.

Thisguideassumesthat—

•allthehardware,software,andnetworkcomponentsofyourObjet350

systemareinstalled,configured,andoperatingcorrectly.

•theoperatorhasaworkingknowledgeoftheWindows

®

PCplatform.

For More Information

Visithttp://www.stratasys.com/todownloadadditionaldocumentsforthis

printer,includingdocumentsinotherlanguages.Alsoavailableonthissite:

detailsaboutconsumablesandsupportcontacts.

Ifyouhaveanyquestionsorcommentsaboutthewayinformationis

presentedinthisdocument,orifyouhaveanysuggestionsforfutureeditions,

pleasesendamessagetoc-support@stratasys.com.

Objet350 User Guide 1 About This Guide

DOC-17001 Rev.G 1-3

Terms Used in This Guide

Build tray

In Objet Studio software:Thesurfacedisplayedonthescreen

thatrepresentstheactualbuildtrayintheprinter.

In the printer:Thesurfaceuponwhichmodelsareproduced.

Cleaning fluid Cleanserforflushingmaterialfeedtubesandtheprintingblock,

usedtocompletelyremoveModelandSupportmaterialfrom

thesystembeforeloadinganothertypeofmaterialinthe

printerandbeforelong-termshutdown.Thecleaningfluidis

suppliedinstandardmaterialcartridges.

Client/user workstation Theworkstationonwhichsoftwareisinstalledforpreparing

buildtraysforproductiononPolyJetprinters.(Thereisnolimit

tothenumberofclientworkstationsinthelocalnetwork.)

Connex™ Thetechnologyofprintingmodelsbyjettingmultiplematerials

simultaneouslyfromtheprintheads.Thistechnologyenables

Objet350printerstoprintinDigitalMaterialmode.

Digital Material Combinationsofmodelmaterialsfabricatedintheprinterfrom

thebasicmodelmaterialsinstalled.

Digital Material Mode Theprintermodeusedtoprintajobusingtwodifferentmodel

materials.(Thismodecanalsobeusedtoeliminatetheneedfor

performingtheMaterialReplacementprocedurewhenprinting

withasinglemodelmaterial.)

host/server workstation TheworkstationthatinterfacesdirectlywiththeObjet350

printerandistypicallypositionednexttoit.

Job Manager™ ThepartofObjetStudiosoftwarethatmanagesproductionjobs

beforetheyaresenttothePolyJetprinter.

Mixed part Modelswhosepartsareprintedusingmorethanonemodel

material.

Mixed tray Abuildtraycontainingobjects,eachofwhichisdesignedtobe

printedusingadifferentmodelmaterial.

Model material Materialusedforbuildingmodels.

Objet Studio™ SoftwarethatpreparesfilesforprintingonStratasysPolyJet

printers.

OBJDF Theextensionofafilethatcontainsinformationaboutthe

geometryofanobjectandthematerialsrequiredtoprintit.

objdffilesarecreatedinObjetStudio.

OBJTF Theextensionofafilethatcontainsalloftheinformation

neededforamodel-printingjobonPolyJet3Dprinters.An

objtffileisusedbyObjetStudiotosendaprintjobtoaPolyJet

3Dprinter.

OBJZF Theextensionofacompressed“wrapper”filecontainingallof

thefilesusedinanObjetStudiobuildtray.Usingobjzffiles,a

printingjobcanbesavedasasinglefile,forconvenientstorage

andtransfer.

Objet™ printer TheStratasys3Dprinterreferredtointhisguide.

Printer computer

ThecomputerinsidetheObjet350printerthatoperatesit.

Objet350 User Guide 1 About This Guide

DOC-17001 Rev.G 1-4

Printer interface TheGUI(graphicaluserinterface)usedforcontrollingthe

Objet350printer.

Printer software SoftwarerunningonthecomputerinsidetheObjet350printer,

thatcontrolsallprinteroperations.

Resin Thebasesubstancefromwhichphotopolymerprinting

materialsaremadeforuseinStratasysPolyJetprinters.In

ObjetStudioandprinter-applicationscreens,“resin”refersto

cartridgesofmodelandsupportmaterials.

SLC AfiletypeusedwithObjetStudio,containingbitmapsof

individualslicesoftheobject.

STL

AfiletypeusedwithObjetStudiosoftware.

Support material Materialusedforsupportingthestructureofmodelsduring

production.

DOC-17001 Rev.G 2-1

2

Safety

SafetyFeatures 2-2

SymbolsandWarningLabels 2-3

SafetyGuidelines 2-4

PrinterInstallation 2-4

PrinterOperation 2-4

UVRadiation 2-5

PrinterMaintenance 2-5

ModelandSupportMaterials 2-5

UVLamps 2-6

FirstAidforWorkingwithPrintingMaterials 2-7

ContactwithSkin 2-7

ContactwithEyes 2-7

Ingestion 2-7

Inhalation 2-8

WasteDisposal 2-8

Objet350 User Guide 2 Safety

DOC-17001 Rev.G 2-2

Safety Features

Stratasys3DprintersaredesignedtocomplywithCEandFCC

standards.Theyareequippedwiththefollowingsafetyfeatures:

Cover Interlock Switch

ThepowersuppliedtotheUVlamp(s),thetrayheaterandthe

motionmotorsisturnedoffwhenthecoverisopened.

Warning

Do not defeat (override) the interlock switch.Doingsocould

resultinseriouspersonalinjury.Iftheinterlockswitchdoesnot

functioncorrectly,donotusetheprinter,andcontactyourservice

provider.

Safety Lock

Thecoverislockedwhiletheprinterisworking.Ifyoudo

managetoliftit,theUVlampsandthemotionmotorsturnoff.

Warning

Do not defeat (override) the safety lock.Doingsocouldresult

inseriouspersonalinjury.Ifthesafetylockdoesnotfunction

correctly,donotusetheprinter,andcontactyourserviceprovider.

UV Screening

ThetransparentsectionofthecoverblocksharmfulUV

radiation,allowingtheoperatortoviewthemodelasitisbeing

made.



Figure2-1 FrontviewoftheObjet350printer

Circuit Breaker

Thepowertotheprinteristurnedoffincaseofelectrical

overcurrent.

Note: Thecircuitbreakerisonlyaccessibletoservice

personnel.

UV-Lamp Overheating

Protection

ThepowersuppliedtotheUVlampandthemotionmotorsis

turnedoffifthetemperaturearoundthelampreaches90°C

(194°F).AlabelontheUV-lampcoverindicatesifthe

temperaturehasexceeded65°C(150°F).



Objet350 User Guide 2 Safety

DOC-17001 Rev.G 2-3

Grounded Chassis Thechassisoftheprinterisgrounded,topreventelectrical

shock.

Note:Thepoweroutletmustbeproperlygrounded,in

accordancewiththelocalelectriccode,toprovidethis

protection.

IftheObjet3503Dprintingsystemisnotusedasspecifiedinthisguide,

thesafetyfeaturesmaynotprovideadequateprotection.

Symbols and Warning Labels

ThisfollowingtableliststhewarninglabelslocatedonorinObjet350

printers.

Warning Symbol Meaning Location Comments

Hazard(general) Onthenameplateonthe

backoftheprinter.

Readtheinstructionsin

thisdocumentbefore

operatingtheprinter.

Hotsurface Ontheprintblock. Riskofburns.Donot

touchthissurfaceafter

printing.

Highvoltage NeartheUVlamp

connectors.

Nearthepower-supply

enclosures.

Riskofelectricshock.

Ultraviolet

radiation

NeartheUVlamps. Riskofinjuryfrom

ultravioletradiation.

Movingparts Onthepanelthatis

visiblewhenyouopen

thefrontdoorsofthe

printer.

Riskofinjuryfrommoving

parts.

Objet350 User Guide 2 Safety

DOC-17001 Rev.G 2-4

Safety Guidelines

Thefollowinggeneralguidelines,togetherwiththeinstructionsprovided

throughoutthisuserguide,ensureusersafetywhileoperatingand

maintainingthesystem.If the system is not operated as specified,

the user's safety may be compromised.

Printer

Installation

➢ Installationandremovaloftheprintershouldonlybedonebyqualified

servicepersonnel.

➢ Connecttheprinter(andtheUPSunit)totheelectricoutletusingapower

cordthatissafety-certified.

➢ Theelectricoutletshouldbeeasilyaccessible,neartheprinter.

➢ Neverconnectthepowerplugtoanoutletthatdoesnothaveaground

(earth)wire,andneverdisconnecttheground.Doingsomightexposethe

operatortoseriousdangerfromelectricshock.

➢ ThefollowingsafetystatementisfollowedbytranslationstoFinish,

Norwegian,SwedishandDanish,asrequiredbylocalregulations:

“Themachinemustbeconnectedtoagroundedpoweroutlet.”

❒ FI:Laiteonliitettäväsuojakoskettimillavarustettuunpistorasiaan.

❒ NO:Apparatetmåtilkoplesjordetstikkontakt.

❒ SE:Apparatenskallanslutastilljordatuttag.

❒ DK:Apparatetsstikpropskaltilsluttesenstikkontaktmedjord,som

giverforbindelsetilstikproppensjord.

➢ Leaveaminimumof15centimetersbetweenventilationopeningsand

wallsorotherobjects.

Printer

Operation

➢ TheprintershouldonlybeoperatedbypersonstrainedbyaStratasys

customer-supportrepresentative.

➢ Allpersonsoperatingormaintainingtheprintershouldknowthelocation

offirstaidandemergencyequipmentandhowtouseit.Never block

access to this equipment.

➢ Keepfingersandotherbodypartsclearoftheprintercoverwhenclosing

it.

➢ Neverattempttoopentheprintercoverwhileitisworking.

➢ Neveroverridetheinterlocksafetyswitch.

➢ Iftheinterlocksafetyswitcheverfails,do not use the printer.

➢ Severalpartsoftheprinterremainextremelyhotevenafterithasstopped

operating.AvoidtouchingtheUVlampsandtheprintblock.

Objet350 User Guide 2 Safety

DOC-17001 Rev.G 2-5

UV Radiation

TheUVlampsusedintheprinteremitdangerousradiation.

➢ IftheUVlampsremainonwhentheprinterisopen,donotstaredirectly

attheUVlight.ShutdowntheprinterandcallyourStratasysservice

provider.

Printer

Maintenance

➢ Serviceoperationsshouldbeperformedonlybyqualifiedpersonnelwho

havebeeninstructedinrelevantsafetyprecautions.

➢ Notifyco-workersandthosewhohaveaccesstotheObjet350system

beforebeginningnon-routineandhazardouswork.

Reportanypotentialdangersandsafety-relatedaccidentstoyoursafety

officerortootherappropriateauthorities.

Model and

Support

Materials

ModelandSupportmaterialsaremadeofchemicalsubstances.Although

precautionsmustbetakenwhenhandlingthesematerialsdirectly,allModel

andSupportmaterialsusedbytheObjet350systemarehandledinsealed

cartridges.Normally,operatorsoftheprintershouldneverbedirectlyexposed

tohazardousmaterials.Intheunlikelyeventofaleakorspill,followthe

instructionsthatareincludedwiththeprinting-materialcartridgeused.

➢ StoreModelandSupportmaterialsindoors,inadryareawithadequate

ventilation,between15-25degreesCelsius(59-77degreesFahrenheit).

Neverexposethemtoflames,heat,sparks,ordirectsunlight.

➢ KeepModelandSupportmaterialsawayfromareaswherefoodanddrink

arestored,preparedandconsumed.

➢ Uncuredprintingmaterialisconsideredahazardoussubstance,requiring

certainprecautionswhendirectlyhandlingit.Topreventskinirritation,

wearneopreneornitrile gloves.IfthereisanychancethatModeland

Supportmaterialsmightsplashintotheeyes,wearsafetygoggles.

Prolongeddirectcontactwithprintingmaterialscancauseanallergic

reaction.

➢ WhenhandlingUV-curedmodelsthatmaynotbecompletelycuredonthe

surface,commonlatexglovesareadequate.

➢ Topreventrespiratoryirritation,ventilateareaswhereModelandSupport

materialsareused.Iftheprinterisnotequippedwithanexhaustduct,the

roomventilationsystemshouldreplacetheairatleast20timesperhour.

➢ CleanupModel-materialandSupport-materialspillswithdisposable

towelsorotherabsorbent,non-reusablematerial,suchassawdustor

activatedcharcoal.Rinsethespillareawithdenaturedorisopropylalcohol

(IPA),followedbysoapandwater.Disposeoftheabsorbentmaterialin

accordancewithlocalregulations.

➢ Donotwashcontaminatedclothingathome;clothingshouldbe

professionallylaundered.

➢ Disposeofcontaminatedshoes,beltsandotherleatheritemsin

accordancewithanyapplicableregulations.Absorbedprintingmaterial

mayre-exposetheuserwhentheseitemsareworn.

Objet350 User Guide 2 Safety

DOC-17001 Rev.G 2-6

UV Lamps

UVlampsusedbytheprintertocureprintingmaterialscontainasmall

amountofmercury.Intheunlikelyeventoflampbreakage,avoidinhaling

mercuryvapor,andventilatetheroom.Ifthelampruptures(breaks)during

operation,leavetheroomandventilateitthoroughlyforabout30minutes.

Useprotectiveglovestopreventcontactwithmercuryandotherlamp

components.Carefullyremovespilledmercurywithamethodthatprevents

thegenerationofmercuryvapor,suchasasyringe,packingtapeorpaper.

Placethebrokenlamp,mercuryandcontaminatedmaterialsinanair-tight,

non-metalliccontainer.Disposeofthecontainerinaccordancewith

applicableregulations.

Objet350 User Guide 2 Safety

DOC-17001 Rev.G 2-7

First Aid for Working with Printing Materials

Ingeneral,trytoavoiddirectcontactwithuncuredprintingmaterial.Ifskin

oreyescomeintocontactwithit,washtheareaimmediatelyandthoroughly

withwater,andfollowthesefirst-aidinstructions.

TheMaterialSafetyDataSheet(MSDS)thataccompaniesprinting

materialscontainsimportantsafetyinformation.Keepthisinanaccessible

placewherethesematerialsareusedandstored.

Contact with

Skin

Ifuncuredprintingmaterialcomesincontactwithskin,washtheaffected

areaimmediatelyandthoroughlywithsoapandcoolwater,thenremove

contaminatedclothing.Payparticularattentiontoflushingthehair,ears,

noseandotherpartsofthebodythatarenoteasilycleaned.

➢ Usecoolwatertopreventskinporesfromopening,sothattheliquid

materialdoesnoteasilypenetratetheskin.

➢ Donotusesolventstocleanskin.

➢ Iflargeareasofskinhavebeenexposed,orifprolongedcontactresultsin

blisters,seekmedicalattention.Inanycase,ifirritationpersists,seek

medicalattention.

➢ Avoidtheaccidentaltransferofprintingmaterialfromthehandstoother

areasofthebody,especiallytotheeyes.

➢ Ifprotectivecreamwasused,donotreapplyituntiltheskinhasbeen

completelycleansed.

Contact with

Eyes

Ifuncuredprintingmaterialcomesincontactwiththeeyes,flush

immediatelywithlargeamountsofwaterfor15minutesandseekmedical

attention.

➢ Avoidsunlight,fluorescentlight,andothersourcesofultravioletradiation.



Wearingcontactlenseswhenhandlingliquidprintingmaterialsisnot

recommended.Iftheliquidsplashesintotheeyeswhencontactlensesare

worn,immediatelyremovethelensesandflushtheeyeswithwater.

➢ Cleananddisinfectthecontaminatedlenses.

➢ Donotwearcontactlensesuntileyeirritationdisappears.

Ingestion

Ifprintingmaterialisswallowed,refertotheinstructionsincludedwiththe

cartridge.Seek medical attention immediately.

Objet350 User Guide 2 Safety

DOC-17001 Rev.G 2-8

Inhalation

Vaporsfromprintingmaterialscanbeirritatingtotherespiratorysystem.If

respiratoryirritationoccurs,exposethevictimtofreshairimmediately.

➢ Ifthevictimhasstoppedbreathing,performartificialrespirationor

cardiopulmonaryresuscitation.

➢ Seekmedicalattentionimmediately.

➢ Keepthevictimwarmbutnothot.

➢ Neverfeedanythingtoanunconsciousperson.

➢ Oxygenshouldbeadministeredbyauthorizedpersonnelonly.

Waste Disposal

Fullycuredprintedmodelscanbedisposedofasordinaryofficetrash.

However,specialcareisrequiredwhenhandlingprinterwaste(uncured

printingmaterial).

Printing

Materials

➢ WhenremovingthewastecontainerfromtheObjet350printer,wear

neopreneornitrilegloves.

➢ Topreventliquidwastefromsplashingintotheeyes,wearsafetygoggles.

➢ LiquidwastefromtheObjet350printerisclassifiedashazardousindustrial

waste.Therefore,printing-materialwastemustbepackagedanddisposed

ofinamannerthatpreventshumancontactwithitandcontaminationof

watersources.

➢ EmptyModel-materialandSupport-materialcartridgescontainresidueof

theircontents.Someleakageofthisresiduemayoccurthroughthebroken

cartridgeseal.Therefore,handleandstoreemptycartridgeswithcare.

➢ Donotattempttoreuseemptycartridges,anddonotpuncturethem.

➢ Disposeofusedcartridgesandwastecontainersinaccordancewithlocal

regulations.

➢ Discardcontaminatedclothing,shoes,emptycontainers,etc.,in

accordancewithanyapplicableregulations.

UVLamps

UVlampsusedbytheprintertocureprintingmaterialscontainasmall

amountofmercury,andareconsidered“UniversalWaste.”Recycleordiscard

usedlampsinaccordancewithapplicableregulations.

Brokenlamps:

Afterventilatingthearea,useprotectiveglovesandcarefullyremovespilled

mercurywithamethodthatpreventsthegenerationofmercuryvapor,such

asasyringe,packingtapeorpaper.Placethebrokenlamp,mercuryand

contaminatedmaterialsinanair-tight,non-metalliccontainer.Disposeofthe

containerinaccordancewithapplicableregulations.

DOC-17001 Rev.G 3-1

3

Introducing the Objet350

3D Printing System

WelcometoConnex™Printing 3-2

WorkConfigurations 3-3

SourceFiles 3-4

STLFiles 3-4

SLCFiles 3-4

VRMLFiles 3-4

Workflows 3-5

PrintingMaterials 3-6

Storage 3-6

ShelfLife 3-6

ExposuretoLight 3-6

SafetyConsiderations 3-7

Disposal 3-7

WorkEnvironment 3-7

WorkstationRequirements 3-7

PreparingFilesforUsewithPolyJet3DPrintingSystems 3-8

ConvertingCADFilestoSTLFormat 3-8

ConvertingCADFilestoWRLFormat(VRML) 3-8

ConvertingCADFilestoSLCFormat 3-8

ObjetStudioSoftware 3-9

Page is loading ...

Stratasys Objet350 User manual

This manual is also suitable for

Stratasys Objet350 User manual

Related papers

Other documents