Simplicity MANUAL, OPS/SETUP, VICTA TRACTOR SERIES V80 User manual

Brand: Simplicity

Model: MANUAL, OPS/SETUP, VICTA TRACTOR SERIES V80

Category: Lawnmowers

Type: User manual

This manual is also suitable for

2691004

Part No. 1752636

Revision ‘-’

Riding Mower Model V80

Model No. Description

2691002 Victa, 12.5HP w/38" Mower Deck

2691003 Victa, 14.5HP w/38" Mower Deck

2691004 Victa, 15.5HP w/38" Mower Deck

Operator’s Manual

Not for

Reproduction

Thank you for purchasing this quality-built VICTA mower. We are pleased that you’ve placed your confidence in the VICTA

brand. When operated and maintained according to the instructions in this manual, your VICTA mower will provide many years

of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with mowers and how to

avoid them. Because the manufacturer does not necessarily know all the applications this mower could be used for, it is

important that you read and understand these instructions. Save these original instructions for future reference.

This mower requires final assembly before use. Refer to the Assembly section of this manual for instructions on final

assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find support and service for your mower. There are many authorized service dealers who provide

quality service. You can also contact Customer Service by phone at 1800 356 632, or on the Internet at www.victa.com.

Mower

Model Number _____________________________________

Serial Number _____________________________________

Engine

Model/Type/Code _____________________________________

Date Purchased

or transmitted in any form without the express written permission of

Briggs & Stratton Power Products Group, LLC.

VICTA is a trademark of Briggs & Stratton Power Products Group, LLC

Not for

Reproduction

(#4)

(#9)

(#8)

(#7)

(#5)

(#3)

(#6)

(#1)

(#2)

Not for

Reproduction

4 www.victa.com

14 15

9 10

Not for

Reproduction

16 17

1918

C D

7101935

Not for

Reproduction

6 www.victa.com

3 3,4,5,6

21 23

3 3,4,5,6

Not for

Reproduction

Not for

Reproduction

8 www.victa.com

(#1)

(#2)

(#3)

(#5)

(#6)

(#7)

(#8)

(#9)

(#10)

(#4)

A B C

F G

K M N OL

B C D E F G H

J K L M

max 10°

max ±150N max ±90N

Not for

Reproduction

English

Table of Contents

Operator Safety .................................. 10

Assembly ...................................... 15

Front Wheels ................................................. 15

Seat ........................................................ 15

Steering Wheel ............................................... 15

Maintenance Free Battery ....................................... 15

Important! Before You Start Mowing .............................. 16

Features and Controls ............................. 17

Location of Controls ........................................... 17

Attachments ................................................. 17

Operation ...................................... 18

Before Operating .............................................. 18

Operation - Gear Drive Models ................................... 19

Operation - Hydro-Drive Models .................................. 21

Maintenance ................................... 25

Maintenance Chart ............................................ 25

General Recommendations ...................................... 26

Maintenance - Tractor .......................................... 26

Maintenance - Engine .......................................... 29

Storage (over 30 days) ......................................... 31

How to Order Replacement Parts ................................. 31

Troubleshooting ................................. 32

Warranties ..................................... 34

Not for

Reproduction

10 www.victa.com

Operator Safety

International Pictorials

IMPORTANT: The following pictorials are lo cated on your

unit or on literature supplied with the product. Before you

operate the unit, learn and understand the purpose for each

pictorial.

NOTE: Illustrations and pictorials begin on page 3.

Safety Warning Pictorials (Figure 26)

A - SAFETY ALERT: Read Important Safety Information.

B - IMPORTANT: Read Owner’s Manual Before Operating

This Machine.

C - WARNING: Thrown Objects. Keep Bystanders Away.

Read User Instructions Before Operating This Machine.

D - WARNING: Do Not Use This Machine On Slopes Greater

Than 10 Degrees.

E - DANGER: Keep People, Especially Children, Away From

Unit.

F - DANGER: Keep Feet And Hands Away From Rotating

Blade.

G - DANGER: Keep Hands And Feet Away.

H - DANGER: Fire Hazard. Gasoline And Yard Debris Are

Flammable.

I - WARNING: Hot Surface.

J - DANGER: No Sparks, Flames or Smoking.

K - DANGER: Carbon Monoxide Hazard. The Engine Emits

Poisonous Carbon Monoxide Gas.

L - WARNING: Use Caution When Connecting Or

Disconnecting Accessories.

M - DANGER: Shield Eyes. Explosive Gases Can Cause

Blindness Or Injury.

N - DANGER: Sulfuric Acid Can Cause Blindness Or Severe

Burns.

O - DANGER: Flush Eyes With Water. Get Medical Help Fast.

Control and Operating Pictorials (Figure 27)

A - Engine Start

B - Lights

C - Stop / Off

D - Run / On

E - Brake

F - Parking Brake

G - Clutch

H - Slow

I - Fast

J - Choke

K - Oil

L - Blade Rotation Control

M - Fuel

Responsibility of the Owner

Know your product: If you understand the unit and how the

unit operates, you will get the best performance. As you read

this manual, compare the illustrations to the unit. Learn the

location and the function of the controls. To help prevent

an accident, follow the operating instructions and the safety

rules. Keep this manual for future reference.

WARNING: Look for this symbol to indicate

important safety precautions. This symbol

indicates: “Attention! Become Alert! Your Safety Is

At Risk.”

WARNING: This cutting machine is capable of

amputating hands and feet and throwing objects.

Failure to observe the following safety instructions

could result in serious injury or death to the

operator or bystanders.

The responsibility of the owner is to follow the instructions

below.

Not for

Reproduction

Operator Safety

Operating Safety

Power equipment is only as safe as the operator. If it is misused, or

not properly maintained, it can be dangerous! Remember, you are

responsible for your safety and that of those around you.

Use common sense, and think through what you are doing. If you

are not sure that the task you are about to perform can be safely

done with the equipment you have chosen, ask a

professional: contact your local authorized dealer.

Read the Manual

The operator’s manual contains important safety information you need to be

aware of BEFORE you operate your unit as well as DURING operation.

Safe operating techniques, an explanation of the product’s features and

controls, and maintenance information is included to help you get the

most out of your equipment investment.

Be sure to completely read the Safety Rules and Information found

on the following pages. Also completely read the Operation section.

Children

Tragic accidents can occur with children. Do not allow them

anywhere near the area of operation. Children are often at-

tracted to the unit and mowing activity. Never assume that

children will remain where you last saw them. If there is a

risk that children may enter the area where you are mow-

ing, have another responsible adult watch them.

DO NOT GIVE CHILDREN RIDES ON THIS UNIT! This

encourages them to come near the unit in the future while it

is running, and they could be seriously hurt. They may then

approach the unit for a ride when you are not expecting it,

and you may run over them.

Reverse

Do not mow in reverse unless ab-

solutely necessary. Always look down

and behind before and while

traveling in reverse even with

the mower blades disen-

gaged.

Not for

Reproduction

12 www.victa.com

Operator Safety

Slope Operation

You could be seriously injured or even killed if you use this unit on too

steep an incline. Using the unit on a slope that is too steep or where you

don’t have adequate traction can cause you to lose control or roll over.

A good rule of thumb is to not operate on any slope you cannot back up

(in 2-wheel drive mode). You should not operate on inclines with a slope

greater than a 3.5 ft (1,5 m) rise over a 20.0 ft (6,0 m) length. Always

drive up and down slopes: never cross the face.

Also note that the surface you are driving on can greatly impact stability

and control. Wet grass or icy pavement can seriously affect your ability

to control the unit.

If you feel unsure about operating the unit on an incline, don’t do it. It’s

not worth the risk.

Moving Parts

This equipment has many moving parts that can injure you or someone else. How-

ever, if you are seated in the seat properly, and follow all the rules in this book, the

unit is safe to operate.

The mower deck has spinning mower blades that can amputate hands and feet.

Do not allow anyone near the equipment while it is running!

To help you, the operator, use this equipment safely, it is equipped with an operator-

present safety system. Do NOT attempt to alter or bypass the system. See your

dealer immediately if the system does not pass all the safety interlock system

tests found in this manual.

Thrown Objects

This unit has spinning mower blades. These blades can pick up and throw debris

that could seriously injure a bystander. Be sure to clean up the area to be

mowed BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge guard (de-

flector) in place.

Also, do not allow anyone in the area while the unit is running! If someone does

enter the area, shut the unit off immediately until they leave.

Fuel and Maintenance

Gasoline is extremely flammable. Its vapors are also extremely flammable and

can travel to distant ignition sources. Gasoline must only be used as a fuel, not

as a solvent or cleaner. It should never be stored any place where its vapors

can build up or travel to an ignition source like a pilot light. Fuel belongs in an

approved, plastic, sealed gas can, or in the tractor fuel tank with the cap se-

curely closed. Spilled fuel needs to be cleaned up immediately.

Proper maintenance is critical to the safety and performance of your unit. Be

sure to perform the maintenance procedures listed in this manual, especially pe-

riodically testing the safety system.

Not for

Reproduction

Operator Safety

Safe Operation Practices

For Ride-On (Riding) Rotary Mower Machines

Training

1. Read the instructions carefully. Be familiar with the

controls and the proper use of the equipment.

2. Never allow children or people unfamiliar with these

instructions to use the mower. Local regulations may

restrict the age of the operator.

3. Never mow while people, especially children, or pets

are nearby.

4. Keep in mind that the operator or user is responsible

for accidents or hazards occur ring to other people or

their property.

5. Do not carry passengers.

6. All drivers should seek and obtain pro fessional

and practical instruction. Such instruction should

emphasize:

a. the need for care and concentration when working

with ride-on machines;

b. control of a ride-on machine sliding on a slope will

not be regained by the application of the brake. The

main reasons for loss of control are:

• insufficient wheel grip;

• being driven too fast;

• inadequate braking;

• the type of machine is unsuitable for its task;

• lack of awareness of the effect of ground

conditions, especially slopes;

• incorrect hitching and load dis tribution.

Preparation

1. While mowing, always wear substantial footwear and

long trousers. Do not operate the equipment when

barefoot or wearing open sandals.

2. Thoroughly inspect the area where the equipment is to

be used and remove all ob jects which may be thrown

by the machine.

3. WARNING – Gasoline is highly flammable.

a. Store fuel in containers specifically de signed for

this purpose.

b. Refuel outdoors only and do not smoke while

refuelling.

c. Add fuel before starting the engine. Never remove

the cap of the fuel tank or add fuel while the engine

is run ning or when the engine is hot.

d. If fuel is spilled, do not attempt to start the engine

but move the machine away from the area of

spillage and avoid creating any source of ignition

until fuel vapors have dissipated.

e. Replace all fuel tanks and container caps securely.

4. Replace faulty silencers.

5. Before using, always visually inspect to see that the

blades, blade bolts and cutter as sembly are not worn or

damaged. Replace worn or damaged blades and bolts

in sets to preserve balance.

6. On multi-blade machines, take care as ro tating one

blade can cause other blades to rotate.

Operation

1. Do not operate the engine in a confined space where

dangerous carbon monoxide fumes can collect.

2. Mow only in daylight or in good artificial light.

3. Before attempting to start the engine, dis engage all

blade attachment clutches and shift into neutral.

4. Do not use on slopes of more than 10 de grees.

5. Remember there is no such thing as a “safe” slope.

Travel on grass slopes re quires particular care. To

guard against overturning:

a. do not stop or start suddenly when going up or

downhill;

b. engage clutch slowly, always keep machine in gear,

especially when tra velling downhill;

c. machine speeds should be kept low on slopes and

during tight turns;

d. stay alert for humps and hollows and other hidden

hazards;

e. never mow across the face of the slope, unless the

mower is designed for this purpose.

Not for

Reproduction

14 www.victa.com

Operation (Continued)

6. Use care when pulling loads or using heavy equipment.

a. Use only approved drawbar hitch points.

b. Limit loads to those you can safely control.

c. Do not turn sharply. Use care when reversing.

d. Use counterweight(s) or wheel weights when

suggested in the In struction Book.

7. Watch out for traffic when crossing or near roadways.

8. Stop the blades rotating before crossing surfaces other

than grass.

9. When using any attachments, never direct discharge of

material toward bystanders nor allow anyone near the

machine while in operation.

10. Never operate the mower with defective guards or

shields, or without safety protec tive devices in place.

11. Do not change the engine governor set tings or

overspeed the engine. Operating an engine at excessive

speed may in crease the hazard of personal injury.

12. Before leaving the operator’s position:

a. disengage the power take-off and lower the

attachments;

b. change into neutral and set the park ing brake;

c. stop the engine and remove the key.

13. Disengage drive to attachments, stop the engine,

and disconnect the spark plug wire(s) or remove the

ignition key:

a. before cleaning blockages or unclog ging chute;

b. before checking, cleaning or working on the mower;

c. after striking a foreign object. Inspect the mower

for damage and make re pairs before restarting and

operating the equipment;

d. if the machine starts to vibrate abnor mally (check

immediately).

14. Disengage drive to attachments when transporting or

not in use.

15. Stop the engine and disengage drive to at tachment:

a. before refuelling;

b. before removing the grass catcher;

c. before making height adjustment un less adjustment

can be made from the operator’s position.

16. Reduce the throttle setting during engine run-out and,

if the engine is provided with a shut-off valve, turn the

fuel off at the con clusion of mowing.

17. Before and when backing, look behind and down for

small children.

18. Use extra care when approaching blind corners, shrubs,

trees or other objects that may obscure vision.

Maintenance and Storage

1. On multi-blade machines, take care as ro tating one

blade can cause other blades to rotate.

2. When machine is to be parked, stored or left

unattended, lower the cutting means unless a positive

mechanical lock is used.

3. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

4. Never store the equipment with fuel in the tank inside

a building where fumes may reach an open flame or

spark.

5. Allow the engine to cool before storing in any

enclosure.

6. To reduce the fire hazard, keep the engine, silencer,

battery compartment and fuel storage area free of

grass, leaves, or ex cessive grease.

7. Check the grass catcher frequently for wear or

deterioration.

8. Replace worn or damaged parts for safety.

9. If the fuel tank has to be drained, this should be done

outdoors.

WARNING: The engine exhaust from this product

contains chemicals known to the State of California

to cause cancer, birth defects, or other reproductive

harm.

WARNING: Battery posts, terminals, and related

accessories contain lead and lead compounds -

chemicals known to the State of California to cause

cancer and reproductive harm. Wash hands after

handling.

WARNING: It is a violation of California Public

Resource Code, Section 4442, to use or operate

the engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust system

is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working

order. Other states or federal jurisdictions may

have similar laws. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark

arrester designed for the exhaust system installed

on this engine.

Operator Safety

Not for

Reproduction

Assembly

All fasteners are in the parts bag. Do not discard any parts or

material until the unit is assembled.

WARNING: Before doing any as sembly or

maintenance to the mower, remove the wire from

the spark plug.

NOTE: In this instruction book, left and right describe the

location of a part with the oper ator on the seat.

NOTE: Illustrations and pictorials begin on page 3.

NOTE: To assemble the following loose parts, use the

fasteners shown at full size in Figure 28.

Front Wheels

How To Install The Front Wheels (Figure 1)

Use a knife and cut the four sides of the con tainer. Install the

front wheels (A) in the con tainer.

NOTE: Use a piece of wood about 4 feet (1.25 meters) long

to raise the front of the tractor. If a piece of wood cannot be

found, get another person to help lift the tractor. Be careful,

do not let the tractor fall.

1. Raise the front of the tractor. Set a support (block of

wood) under the tractor.

2. Make sure the valve stem (B) is to the out side of the

tractor. Slide the front wheel (A) on the spindle (C).

3. Fasten each front wheel (A) with washers (D) and (G)

and cotter pin (E). Bend the ends of the cotter pin (E)

apart to keep the front wheel (A) on the spindle (C).

4. After the front wheels (A) are installed, lift the tractor

from the support. Roll the tractor off of the container.

5. If your tractor has hub caps (F), install the hub

caps (F). Make sure the washers (D) hold the hub

caps (F) in place.

Seat

How To Install The Seat (Figure 2)

1. Carefully remove the plastic bag from the seat (A).

2. Align the holes in the seat hinge (B) to the holes in the

seat (A). Fasten the seat (A) to the seat hinge (B) with

the fasteners (D) and (E).

3. Check the operating position of the seat (A). If the

seat (A) needs to be adjusted, loosen the two wing

bolts (E). Slide the seat (A) for ward or backward

along the seat adjusting holes (C). Tighten the wing

bolts (E).

Steering Wheel

How To Assemble The Steering Wheel (Figure 3)

1. Make sure the front wheels point forward.

2. Slide the cover (C) over the steering post (B). Make

sure the collar of the cover (C) is on top.

3. Slide the steering wheel (A) onto the steer ing post (B).

4. Attach the steering wheel (A) to the steer ing post (B)

with screw (D) and washer (E).

5. Some models have an optional insert (F) in the parts

bag. Attach the insert (F) to the centre of the steering

wheel (A).

Maintenance Free Battery

IMPORTANT: Before you attach the battery cables to the

battery, check the battery date. The battery date tells if the

battery must be charged.

1. (Figure 4) Check the top and the side of the battery (A)

for the location of the battery date.

2. If the battery (A) is put into service before the battery

date, the battery cables can be attached with out

charging the battery (A). See “How To Install The

Battery Cables”.

3. If the battery (A) is put into service after the battery

date, the battery (A) must be charged. See “How To

Charge The Battery”.

How To Charge The Battery

WARNING: When you charge the battery, do not

smoke. Keep the bat tery away from any sparks. The

fumes from the battery acid can cause an

explosion.

1. Remove the battery (A) and battery tray (C).

2. Remove the protective cap from the battery terminal.

3. Use a 12 volt battery charger to charge the battery (A).

Charge at a rate of 6 amperes for one hour. If you do

not have a battery charger, have an authorized service

centre charge the battery.

4. Install the battery (A) and battery tray (C). Make sure

the positive (+) terminal (D) is on the left side.

Not for

Reproduction

16 www.victa.com

How To Install The Battery Cables (Figure 4)

WARNING: To prevent sparks, fasten the red cable

to the positive (+) ter minal before you connect the

black cable.

1. Remove the protective caps from the battery terminals.

2. Slide the terminal cover (B) onto the red cable (E).

Fasten the red cable (E) to the positive (+) terminal

(D) with the fasteners (F) and (G).

3. Fasten the black cable (H) to the negative (-) terminal

with the fasteners (F) and (G).

Important! Before You Start Mowing

• Check the engine oil.

• Fill the fuel tank with fuel.

• Check the air pressure of the tires.

• Check the level of the mower hous ing.

• Attach the battery cables.

Check The Tires

Check the air pressure in the tires. Tires with too much air

pressure will cause the unit to ride rough. Also, the wrong

air pressure will keep the mower housing from cutting level.

The correct air pressure is: Front Tires 0,97 BAR (14 PSI),

Rear Tires 0,69 BAR (10 PSI). The tires were over inflated

for shipment.

Check The Level Of The Mower Housing

Make sure the level of cut is still correct. After you mow a

short distance, look at the area that was cut. If the mower

housing does not cut level, see the instructions on “How To

Level The Mower Housing” in the Maintenance section of

this instruction book.

How To Prepare The Engine

Check the oil and fuel levels, and add as needed.

IMPORTANT: Some units are shipped from the factory

without oil in the engine. It is important to check the engine

oil level before attempting to start or operate the unit. If you

start the engine without oil, it will be damaged beyond repair

and will not be covered under warranty.

See the "Operation" section of this manual for the type of

fuel and oil to use. Before you operate the unit, read the

information on safety, oper ation, maintenance, and storage.

WARNING: Follow the instructions in this manual

for the type of fuel and oil to use. Always use a

safety fuel container. Do not smoke when adding

fuel to the engine. When inside an enclosure, do

not fill with fuel. Before you add fuel, stop the

engine. Let the engine cool for at least three

minutes.

Assembly

Not for

Reproduction

Features and Controls

Location of Controls - Gear Drive Models

(Figure 5)

Blade Rotation Control (A) — Use the blade rota tion control

to start and stop the rotation of the blade.

Clutch / Brake Pedal (B) — The pedal has two functions.

The first function is a clutch. The sec ond function is a brake.

Headlight Switch (C) — The headlight switch is the first

part of the ignition switch. To use the lights with the engine

running, turn the key to the position for the lights.

Ignition Switch (C) — Use the ignition switch to start and

stop the engine.

Shift Lever (D) — Use the shift lever to change the speed or

direction of the unit.

Lift Lever (E) — Use the lift lever to change the height of

cut.

Parking Brake Lever (F) — Use the parking brake lever to

engage the brake when you leave the unit.

Throttle Control Lever (G) — Use the throttle control lever

to increase or decrease the speed of the engine.

NOTE: Illustrations and pictorials begin on page 3.

Location of Controls - Hydro-Drive Models

(Figure 6, 19)

Blade Rotation Control (A) — Use the blade rota tion control

to start and stop the rotation of the blade.

Brake Pedal (B) — Use the brake pedal to quickly stop.

Headlight Switch (C) — The headlight switch is the first

part of the ignition switch. To use the lights with the engine

running, turn the key to the position for the lights.

Ignition Switch (C) — Use the ignition switch to start and

stop the engine.

Speed Control Pedal (D) — Use the speed con trol pedal to

change the speed and the direction of the unit.

Lift Lever (E) — Use the lift lever to change the height of

cut.

Parking Brake Lever (F) — Use the parking brake lever to

engage the brake when you leave the unit.

Throttle Control Lever (G) — Use the throttle control lever

to increase or decrease the speed of the engine.

(Figure 19) Automatic Drive Disconnect (A) — Use the

automatic drive disconnect to disengage the transmission.

Attachments

This unit can use many different attachments. This unit

can pull attachments like a lawn sweeper, a lawn aerator,

or a hopper spreader. This unit can not use attachments

that engage the ground like a plough, a disk harrow, or a

cultivator.

For trailer and pull-behind attachments, the maximum weight

is 113 kg (250 lbs.).

Not for

Reproduction

18 www.victa.com

Operation

Before Operating

Check/Add Engine Oil

IMPORTANT: Some units are shipped from the factory

without oil in the engine. It is important to check the engine

oil level before attempting to start or operate the unit. If you

start the engine without oil, it will be damaged beyond repair

and will not be covered under warranty.

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF, SG,

SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard

starting.

** Above 80°F (27°C) the use of 10W-30 may cause

increased oil consumption. Check oil level more frequently.

How To Check/Add Oil (Figure 7)

Before adding or checking the oil

• Place the unit on a level surface.

• Clean the oil fill area of any debris.

1. Raise the tractor hood.

2. Remove the dipstick (A) and wipe with a clean cloth.

3. Insert and tighten the dipstick.

4. Remove the dipstick and check the oil level. It should

be at the top of the full indicator (B) on the dipstick.

5. If low, add oil slowly into the engine oil fill (C). Do

not overfill. After adding oil, wait one minute and then

recheck the oil level.

6. Replace and tighten the dipstick.

Add Fuel

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High

altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is

acceptable.

CAUTION: Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine

to run on alternate fuels. This will damage the engine

components and void the engine warranty.

To protect the fuel system from gum formation, mix a

fuel stabilizer into the fuel. See Storage. All fuel is not the

same. If starting or performance problems occur, change

fuel providers or change brands. This engine is certified to

operate on gasoline. The emissions control system for this

engine is EM (Engine Modifications)

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane/85 AKI (89 RON) gasoline is acceptable. To remain

emissions compliant, high altitude adjustment is required.

Operation without this adjustment will cause decreased

performance, increased fuel consumption, and increased

emissions. See a Briggs & Stratton Authorized Dealer for

high altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet (762

meters) with the high altitude kit is not recommended.

How To Add Fuel (Figure 8)

WARNING: Fuel and its vapors are extremely

flammable and explosive. Fire or explosion can

cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 3 minutes

before removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary

• If fuel spills, wait until it evaporates before starting

engine.

Not for

Reproduction

Operation

1. Raise the tractor hood.

2. Clean the fuel cap area of dirt and debris. Remove the

fuel cap.

3. Fill the fuel tank (A) with fuel. To allow for expansion

of the fuel, do not fill above the bottom of the fuel tank

neck (B).

4. Reinstall the fuel cap.

Operation - Gear Drive Models

Using Controls

How To Use The Throttle Control (Figure 5)

Use the throttle control (G) to increase or de crease the

speed of the engine.

1. The FAST position is marked with a detent. For normal

operation and when using a grass bagger, move the

throttle control to the FAST position. For maximum

charging of the battery and for a cooler running engine,

oper ate the engine in the FAST position.

2. The engine governor is set at the factory for maximum

performance. Do not adjust the governor to increase

the speed of the en gine.

How To Use The Blade Rotation Control (Figure 5)

Use the blade rotation control (A) to engage the blade(s).

1. Before you start the engine, make sure the blade

rotation control (A) is in the DISEN GAGE position.

2. Move the blade rotation control (A) to the ENGAGE

position to rotate the blade(s).

NOTE: If the engine stops when you en gage the

blade(s), the seat switch is not activated. Make sure

you sit in the middle of the seat.

3. Move the blade rotation control (A) to the DISENGAGE

position to stop the blade(s). Before you leave the

operator’s position, make sure the blade(s) has stopped

rotating.

4. Before you ride the unit across a sidewalk or a road,

move the blade rotation control (A) to the DISENGAGE

position.

WARNING: Always keep your hands and feet away

from the blade, deflector opening, and the mower

housing when the engine runs.

How To Use The Shift Lever (Figure 5)

CAUTION: Before you move the shift lever, completely

push the clutch/brake pedal for ward to stop the unit. If the

unit is not stopped, the gearbox can be damaged.

1. Completely push the clutch/brake pedal (B) forward to

stop the unit. Keep your foot on the pedal.

2. Move the throttle control lever (G) to the SLOW

position.

3. To go forward, move the shift lever (D) to a forward

speed setting. To go backward, move the shift lever

(D) to reverse.

4. Slowly release the clutch/brake pedal (B). Do not keep

your foot on the pedal.

5. Move the throttle control (G) to the FAST position.

How To Use The Parking Brake (Figure 5)

1. Completely push the clutch/brake pedal (B) for ward.

2. Lift and hold the parking brake lever (F).

3. Remove your foot from the clutch/brake pedal (B) and

then let go of the parking brake lever (F). Make sure

the parking brake will hold the unit.

4. To release the parking brake lever (F), completely push

the clutch/brake pedal (B) forward. The park ing brake

will automatically release.

WARNING: Before you leave the operator’s

position, move the shift lever to the neutral (N)

position. Set the parking brake. Move the blade

rotation con trol to the DISENGAGE position. Stop

the engine and remove the ignition key.

How To Change The Cutting Height (Figure 5)

To change the cutting height, raise or lower the lift lever (E)

as follows.

1. Move the lift lever (E) forward to lower the mower

housing and back to raise the mower housing.

2. When you ride on a sidewalk or road, move the lift

lever (E) to the highest position and move the blade

rotation control (A) to the DIS ENGAGE position.

Not for

Reproduction

20 www.victa.com

Operation

How To Stop The Unit (Figure 5)

1. Completely push the clutch/brake pedal (B) forward to

stop the unit. Keep your foot on the pedal.

2. Move the blade rotation control (A) to the DISENGAGE

position.

3. Move the shift lever (D) to the NEUTRAL position.

4. Set the parking brake (F).

WARNING: Make sure the parking brake will hold

the unit.

5. Move the throttle control (G) to the SLOW position.

6. To stop the engine, turn the ignition key (C) to the OFF

position. Remove the key.

How To Transport The Unit

1. Move the blade rotation control to the DIS ENGAGE

position.

2. Raise the lift lever to the highest position.

3. Move the throttle control to a position be tween SLOW

and FAST.

4. To go faster, move the shift lever to a faster speed.

Mowing

How To Operate With The Mower Housing

IMPORTANT: When you operate with the mower housing,

always operate with the throttle control in the FAST position.

1. Start the engine.

2. Move the lift lever to a height of cut position. In high or

thick grass, cut the grass in the highest position first

and then lower the mower housing to a lower position.

3. Move the throttle control to the SLOW posi tion.

4. Slowly move the blade rotation control to the ENGAGE

position.

5. Push the clutch/brake pedal completely for ward.

6. Move the shift lever to one of the speed set tings.

NOTE: When you mow in heavy grass or mow with a

bagger, put the shift lever in the slowest speed.

7. Slowly release the clutch/brake pedal.

8. Move the throttle control to the FAST posi tion. If you

need to go faster or slower, stop the unit and move the

shift lever to another speed setting.

9. Make sure the level of cut is still correct. After you

mow a short distance, look at the area that was cut.

If the mower housing does not cut level, see the

instructions on “How To Level The Mower Housing” in

the Maintenance section.

WARNING: For better control of the unit, select a

safe speed.

How To Operate On Hills

WARNING: Do not ride up or down slopes that are

too steep to back straight up. Never ride the unit

across a slope.

1. Before you ride up or down a hill, move the shift lever

to the slowest speed.

2. Do not stop or change speed settings on a hill. If you

must stop, quickly push the clutch/brake pedal forward

and set the parking brake.

3. To start again, make sure the shift lever is in the

slowest speed. Move the throttle control to the SLOW

position. Slowly release the pedal.

4. If you must stop or start on a hill, always have enough

space for the unit to roll when you release the brake

and engage the clutch.

5. Be very careful when you change directions on a

hill. When on a slope or in a turn on a hill, move the

throttle control to the SLOW position to help prevent an

accident.

Starting the Engine

NOTE: This unit is equipped with a safety interlock system

that includes a sensor switch for the seat. This system will

stop the engine when the operator leaves the seat. For your

protection, always make sure this system operates correctly.

NOTE: The engine will not start unless you sit in the seat,

depress the clutch/brake pedal, and move the blade rotation

control to the DISENGAGE position.

1. Check oil and fuel levels, and add as needed.

2. Push the clutch/brake brake pedal complete ly forward.

Keep your foot on the pedal.

3. Move the shift lever to the neutral (N) position.

4. Make sure the blade rotation control is in the

DISENGAGE position.

5. Move the throttle control completely forward past the

FAST position to the CHOKE position.

NOTE: The CHOKE position is usually unnecessary

when restarting a warm engine.

6. Turn the ignition key to the START position.

NOTE: If the engine does not start after four or five

tries, see the Troubleshooting section.

7. Slowly move the throttle control to the FAST position.

8. To stop the engine, turn the ignition key to the OFF

position. Remove the key.

Not for

Reproduction

Page is loading ...

Simplicity MANUAL, OPS/SETUP, VICTA TRACTOR SERIES V80 User manual

Brand: Simplicity

Model: MANUAL, OPS/SETUP, VICTA TRACTOR SERIES V80

Category: Lawnmowers

Type: User manual

This manual is also suitable for

2691004

Download PDF

report

Simplicity MANUAL, OPS/SETUP, VICTA TRACTOR SERIES V80 User manual

This manual is also suitable for

Simplicity MANUAL, OPS/SETUP, VICTA TRACTOR SERIES V80 User manual

Related papers

Other documents