Simplicity 2691004 User manual

Category
Lawnmowers
Type
User manual

This manual is also suitable for

Part No. 1752636
Revision ‘-’
Riding Mower Model V80
Model No. Description
2691002 Victa, 12.5HP w/38" Mower Deck
2691003 Victa, 14.5HP w/38" Mower Deck
2691004 Victa, 15.5HP w/38" Mower Deck
Operator’s Manual
!
Not for
Reproduction
Thank you for purchasing this quality-built VICTA mower. We are pleased that you’ve placed your confidence in the VICTA
brand. When operated and maintained according to the instructions in this manual, your VICTA mower will provide many years
of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with mowers and how to
avoid them. Because the manufacturer does not necessarily know all the applications this mower could be used for, it is
important that you read and understand these instructions. Save these original instructions for future reference.
This mower requires final assembly before use. Refer to the Assembly section of this manual for instructions on final
assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to find support and service for your mower. There are many authorized service dealers who provide
quality service. You can also contact Customer Service by phone at 1800 356 632, or on the Internet at www.victa.com.
Mower
Model Number _____________________________________
Serial Number _____________________________________
Engine
Model/Type/Code _____________________________________
Date Purchased
Copyright © 2011 All rights reserved. No part of this material may be reproduced
or transmitted in any form without the express written permission of
Briggs & Stratton Power Products Group, LLC.
VICTA is a trademark of Briggs & Stratton Power Products Group, LLC
Not for
Reproduction
3
1
4
7
2
5
3
D
A
A
C
F
E
(#4)
(#9)
(#8)
G
B
D
C
(#7)
B
E
(#5)
C
B
D
A
E
F
(#3)
(#6)
F
(#1)
C
A
A
A
F
B
B
C
D
E
(#2)
H
E
B
G
C
A
D
F
6
E
B
G
C
A
D
F
8
B
A
G
Not for
Reproduction
4 www.victa.com
11
C
D
E
A
B
12
E
D
A
B
C
D
F
13
14 15
A
B
C
A
B
C
A
B
9 10
A
B
G
A
B
D
C
E
F
Not for
Reproduction
5
16 17
1918
A
B
C
A
B
D
B
C D
7101935
Not for
Reproduction
6 www.victa.com
B
C
D
A
A
11
22
3 3,4,5,6
A
21 23
11
22
3 3,4,5,6
22
20
D
1
2
3
4
5
6
A
D
C
1
3
2
5
4
6
6
7
C
F
E
I
H
G
B
B
C
Not for
Reproduction
7
A
24
25
A
A
B
C
D
E
C
Not for
Reproduction
8 www.victa.com
28
(#1)
(#2)
(#3)
(#5)
(#6)
(#7)
(#8)
(#9)
(#10)
(#4)
26
27
A B C
D
E
F G
H
I
J
K M N OL
A
B C D E F G H
I
J K L M
max 10°
max ±150N max ±90N
Not for
Reproduction
English
9
Table of Contents
Operator Safety .................................. 10
Assembly ...................................... 15
Front Wheels ................................................. 15
Seat ........................................................ 15
Steering Wheel ............................................... 15
Maintenance Free Battery ....................................... 15
Important! Before You Start Mowing .............................. 16
Features and Controls ............................. 17
Location of Controls ........................................... 17
Attachments ................................................. 17
Operation ...................................... 18
Before Operating .............................................. 18
Operation - Gear Drive Models ................................... 19
Operation - Hydro-Drive Models .................................. 21
Maintenance ................................... 25
Maintenance Chart ............................................ 25
General Recommendations ...................................... 26
Maintenance - Tractor .......................................... 26
Maintenance - Engine .......................................... 29
Storage (over 30 days) ......................................... 31
How to Order Replacement Parts ................................. 31
Troubleshooting ................................. 32
Warranties ..................................... 34
Not for
Reproduction
10 www.victa.com
Operator Safety
International Pictorials
IMPORTANT: The following pictorials are lo cated on your
unit or on literature supplied with the product. Before you
operate the unit, learn and understand the purpose for each
pictorial.
NOTE: Illustrations and pictorials begin on page 3.
Safety Warning Pictorials (Figure 26)
A - SAFETY ALERT: Read Important Safety Information.
B - IMPORTANT: Read Owner’s Manual Before Operating
This Machine.
C - WARNING: Thrown Objects. Keep Bystanders Away.
Read User Instructions Before Operating This Machine.
D - WARNING: Do Not Use This Machine On Slopes Greater
Than 10 Degrees.
E - DANGER: Keep People, Especially Children, Away From
Unit.
F - DANGER: Keep Feet And Hands Away From Rotating
Blade.
G - DANGER: Keep Hands And Feet Away.
H - DANGER: Fire Hazard. Gasoline And Yard Debris Are
Flammable.
I - WARNING: Hot Surface.
J - DANGER: No Sparks, Flames or Smoking.
K - DANGER: Carbon Monoxide Hazard. The Engine Emits
Poisonous Carbon Monoxide Gas.
L - WARNING: Use Caution When Connecting Or
Disconnecting Accessories.
M - DANGER: Shield Eyes. Explosive Gases Can Cause
Blindness Or Injury.
N - DANGER: Sulfuric Acid Can Cause Blindness Or Severe
Burns.
O - DANGER: Flush Eyes With Water. Get Medical Help Fast.
Control and Operating Pictorials (Figure 27)
A - Engine Start
B - Lights
C - Stop / Off
D - Run / On
E - Brake
F - Parking Brake
G - Clutch
H - Slow
I - Fast
J - Choke
K - Oil
L - Blade Rotation Control
M - Fuel
Responsibility of the Owner
Know your product: If you understand the unit and how the
unit operates, you will get the best performance. As you read
this manual, compare the illustrations to the unit. Learn the
location and the function of the controls. To help prevent
an accident, follow the operating instructions and the safety
rules. Keep this manual for future reference.
WARNING: Look for this symbol to indicate
important safety precautions. This symbol
indicates: “Attention! Become Alert! Your Safety Is
At Risk.”
WARNING: This cutting machine is capable of
amputating hands and feet and throwing objects.
Failure to observe the following safety instructions
could result in serious injury or death to the
operator or bystanders.
The responsibility of the owner is to follow the instructions
below.
Not for
Reproduction
11
Operator Safety
Operating Safety
Power equipment is only as safe as the operator. If it is misused, or
not properly maintained, it can be dangerous! Remember, you are
responsible for your safety and that of those around you.
Use common sense, and think through what you are doing. If you
are not sure that the task you are about to perform can be safely
done with the equipment you have chosen, ask a
professional: contact your local authorized dealer.
Read the Manual
The operator’s manual contains important safety information you need to be
aware of BEFORE you operate your unit as well as DURING operation.
Safe operating techniques, an explanation of the product’s features and
controls, and maintenance information is included to help you get the
most out of your equipment investment.
Be sure to completely read the Safety Rules and Information found
on the following pages. Also completely read the Operation section.
Children
Tragic accidents can occur with children. Do not allow them
anywhere near the area of operation. Children are often at-
tracted to the unit and mowing activity. Never assume that
children will remain where you last saw them. If there is a
risk that children may enter the area where you are mow-
ing, have another responsible adult watch them.
DO NOT GIVE CHILDREN RIDES ON THIS UNIT! This
encourages them to come near the unit in the future while it
is running, and they could be seriously hurt. They may then
approach the unit for a ride when you are not expecting it,
and you may run over them.
Reverse
Do not mow in reverse unless ab-
solutely necessary. Always look down
and behind before and while
traveling in reverse even with
the mower blades disen-
gaged.
Not for
Reproduction
12 www.victa.com
Operator Safety
Slope Operation
You could be seriously injured or even killed if you use this unit on too
steep an incline. Using the unit on a slope that is too steep or where you
don’t have adequate traction can cause you to lose control or roll over.
A good rule of thumb is to not operate on any slope you cannot back up
(in 2-wheel drive mode). You should not operate on inclines with a slope
greater than a 3.5 ft (1,5 m) rise over a 20.0 ft (6,0 m) length. Always
drive up and down slopes: never cross the face.
Also note that the surface you are driving on can greatly impact stability
and control. Wet grass or icy pavement can seriously affect your ability
to control the unit.
If you feel unsure about operating the unit on an incline, don’t do it. It’s
not worth the risk.
Moving Parts
This equipment has many moving parts that can injure you or someone else. How-
ever, if you are seated in the seat properly, and follow all the rules in this book, the
unit is safe to operate.
The mower deck has spinning mower blades that can amputate hands and feet.
Do not allow anyone near the equipment while it is running!
To help you, the operator, use this equipment safely, it is equipped with an operator-
present safety system. Do NOT attempt to alter or bypass the system. See your
dealer immediately if the system does not pass all the safety interlock system
tests found in this manual.
Thrown Objects
This unit has spinning mower blades. These blades can pick up and throw debris
that could seriously injure a bystander. Be sure to clean up the area to be
mowed BEFORE you start mowing.
Do not operate this unit without the entire grass catcher or discharge guard (de-
flector) in place.
Also, do not allow anyone in the area while the unit is running! If someone does
enter the area, shut the unit off immediately until they leave.
Fuel and Maintenance
Gasoline is extremely flammable. Its vapors are also extremely flammable and
can travel to distant ignition sources. Gasoline must only be used as a fuel, not
as a solvent or cleaner. It should never be stored any place where its vapors
can build up or travel to an ignition source like a pilot light. Fuel belongs in an
approved, plastic, sealed gas can, or in the tractor fuel tank with the cap se-
curely closed. Spilled fuel needs to be cleaned up immediately.
Proper maintenance is critical to the safety and performance of your unit. Be
sure to perform the maintenance procedures listed in this manual, especially pe-
riodically testing the safety system.
Not for
Reproduction
13
Operator Safety
Safe Operation Practices
For Ride-On (Riding) Rotary Mower Machines
Training
1. Read the instructions carefully. Be familiar with the
controls and the proper use of the equipment.
2. Never allow children or people unfamiliar with these
instructions to use the mower. Local regulations may
restrict the age of the operator.
3. Never mow while people, especially children, or pets
are nearby.
4. Keep in mind that the operator or user is responsible
for accidents or hazards occur ring to other people or
their property.
5. Do not carry passengers.
6. All drivers should seek and obtain pro fessional
and practical instruction. Such instruction should
emphasize:
a. the need for care and concentration when working
with ride-on machines;
b. control of a ride-on machine sliding on a slope will
not be regained by the application of the brake. The
main reasons for loss of control are:
• insufficient wheel grip;
• being driven too fast;
• inadequate braking;
• the type of machine is unsuitable for its task;
• lack of awareness of the effect of ground
conditions, especially slopes;
• incorrect hitching and load dis tribution.
Preparation
1. While mowing, always wear substantial footwear and
long trousers. Do not operate the equipment when
barefoot or wearing open sandals.
2. Thoroughly inspect the area where the equipment is to
be used and remove all ob jects which may be thrown
by the machine.
3. WARNING – Gasoline is highly flammable.
a. Store fuel in containers specifically de signed for
this purpose.
b. Refuel outdoors only and do not smoke while
refuelling.
c. Add fuel before starting the engine. Never remove
the cap of the fuel tank or add fuel while the engine
is run ning or when the engine is hot.
d. If fuel is spilled, do not attempt to start the engine
but move the machine away from the area of
spillage and avoid creating any source of ignition
until fuel vapors have dissipated.
e. Replace all fuel tanks and container caps securely.
4. Replace faulty silencers.
5. Before using, always visually inspect to see that the
blades, blade bolts and cutter as sembly are not worn or
damaged. Replace worn or damaged blades and bolts
in sets to preserve balance.
6. On multi-blade machines, take care as ro tating one
blade can cause other blades to rotate.
Operation
1. Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
2. Mow only in daylight or in good artificial light.
3. Before attempting to start the engine, dis engage all
blade attachment clutches and shift into neutral.
4. Do not use on slopes of more than 10 de grees.
5. Remember there is no such thing as a “safe” slope.
Travel on grass slopes re quires particular care. To
guard against overturning:
a. do not stop or start suddenly when going up or
downhill;
b. engage clutch slowly, always keep machine in gear,
especially when tra velling downhill;
c. machine speeds should be kept low on slopes and
during tight turns;
d. stay alert for humps and hollows and other hidden
hazards;
e. never mow across the face of the slope, unless the
mower is designed for this purpose.
Not for
Reproduction
14 www.victa.com
Operation (Continued)
6. Use care when pulling loads or using heavy equipment.
a. Use only approved drawbar hitch points.
b. Limit loads to those you can safely control.
c. Do not turn sharply. Use care when reversing.
d. Use counterweight(s) or wheel weights when
suggested in the In struction Book.
7. Watch out for traffic when crossing or near roadways.
8. Stop the blades rotating before crossing surfaces other
than grass.
9. When using any attachments, never direct discharge of
material toward bystanders nor allow anyone near the
machine while in operation.
10. Never operate the mower with defective guards or
shields, or without safety protec tive devices in place.
11. Do not change the engine governor set tings or
overspeed the engine. Operating an engine at excessive
speed may in crease the hazard of personal injury.
12. Before leaving the operator’s position:
a. disengage the power take-off and lower the
attachments;
b. change into neutral and set the park ing brake;
c. stop the engine and remove the key.
13. Disengage drive to attachments, stop the engine,
and disconnect the spark plug wire(s) or remove the
ignition key:
a. before cleaning blockages or unclog ging chute;
b. before checking, cleaning or working on the mower;
c. after striking a foreign object. Inspect the mower
for damage and make re pairs before restarting and
operating the equipment;
d. if the machine starts to vibrate abnor mally (check
immediately).
14. Disengage drive to attachments when transporting or
not in use.
15. Stop the engine and disengage drive to at tachment:
a. before refuelling;
b. before removing the grass catcher;
c. before making height adjustment un less adjustment
can be made from the operator’s position.
16. Reduce the throttle setting during engine run-out and,
if the engine is provided with a shut-off valve, turn the
fuel off at the con clusion of mowing.
17. Before and when backing, look behind and down for
small children.
18. Use extra care when approaching blind corners, shrubs,
trees or other objects that may obscure vision.
Maintenance and Storage
1. On multi-blade machines, take care as ro tating one
blade can cause other blades to rotate.
2. When machine is to be parked, stored or left
unattended, lower the cutting means unless a positive
mechanical lock is used.
3. Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
4. Never store the equipment with fuel in the tank inside
a building where fumes may reach an open flame or
spark.
5. Allow the engine to cool before storing in any
enclosure.
6. To reduce the fire hazard, keep the engine, silencer,
battery compartment and fuel storage area free of
grass, leaves, or ex cessive grease.
7. Check the grass catcher frequently for wear or
deterioration.
8. Replace worn or damaged parts for safety.
9. If the fuel tank has to be drained, this should be done
outdoors.
WARNING: The engine exhaust from this product
contains chemicals known to the State of California
to cause cancer, birth defects, or other reproductive
harm.
WARNING: Battery posts, terminals, and related
accessories contain lead and lead compounds -
chemicals known to the State of California to cause
cancer and reproductive harm. Wash hands after
handling.
WARNING: It is a violation of California Public
Resource Code, Section 4442, to use or operate
the engine on any forest-covered, brush-covered,
or grass-covered land unless the exhaust system
is equipped with a spark arrester, as defined in
Section 4442, maintained in effective working
order. Other states or federal jurisdictions may
have similar laws. Contact the original equipment
manufacturer, retailer, or dealer to obtain a spark
arrester designed for the exhaust system installed
on this engine.
Operator Safety
Not for
Reproduction
15
Assembly
All fasteners are in the parts bag. Do not discard any parts or
material until the unit is assembled.
WARNING: Before doing any as sembly or
maintenance to the mower, remove the wire from
the spark plug.
NOTE: In this instruction book, left and right describe the
location of a part with the oper ator on the seat.
NOTE: Illustrations and pictorials begin on page 3.
NOTE: To assemble the following loose parts, use the
fasteners shown at full size in Figure 28.
Front Wheels
How To Install The Front Wheels (Figure 1)
Use a knife and cut the four sides of the con tainer. Install the
front wheels (A) in the con tainer.
NOTE: Use a piece of wood about 4 feet (1.25 meters) long
to raise the front of the tractor. If a piece of wood cannot be
found, get another person to help lift the tractor. Be careful,
do not let the tractor fall.
1. Raise the front of the tractor. Set a support (block of
wood) under the tractor.
2. Make sure the valve stem (B) is to the out side of the
tractor. Slide the front wheel (A) on the spindle (C).
3. Fasten each front wheel (A) with washers (D) and (G)
and cotter pin (E). Bend the ends of the cotter pin (E)
apart to keep the front wheel (A) on the spindle (C).
4. After the front wheels (A) are installed, lift the tractor
from the support. Roll the tractor off of the container.
5. If your tractor has hub caps (F), install the hub
caps (F). Make sure the washers (D) hold the hub
caps (F) in place.
Seat
How To Install The Seat (Figure 2)
1. Carefully remove the plastic bag from the seat (A).
2. Align the holes in the seat hinge (B) to the holes in the
seat (A). Fasten the seat (A) to the seat hinge (B) with
the fasteners (D) and (E).
3. Check the operating position of the seat (A). If the
seat (A) needs to be adjusted, loosen the two wing
bolts (E). Slide the seat (A) for ward or backward
along the seat adjusting holes (C). Tighten the wing
bolts (E).
Steering Wheel
How To Assemble The Steering Wheel (Figure 3)
1. Make sure the front wheels point forward.
2. Slide the cover (C) over the steering post (B). Make
sure the collar of the cover (C) is on top.
3. Slide the steering wheel (A) onto the steer ing post (B).
4. Attach the steering wheel (A) to the steer ing post (B)
with screw (D) and washer (E).
5. Some models have an optional insert (F) in the parts
bag. Attach the insert (F) to the centre of the steering
wheel (A).
Maintenance Free Battery
IMPORTANT: Before you attach the battery cables to the
battery, check the battery date. The battery date tells if the
battery must be charged.
1. (Figure 4) Check the top and the side of the battery (A)
for the location of the battery date.
2. If the battery (A) is put into service before the battery
date, the battery cables can be attached with out
charging the battery (A). See “How To Install The
Battery Cables”.
3. If the battery (A) is put into service after the battery
date, the battery (A) must be charged. See “How To
Charge The Battery”.
How To Charge The Battery
WARNING: When you charge the battery, do not
smoke. Keep the bat tery away from any sparks. The
fumes from the battery acid can cause an
explosion.
1. Remove the battery (A) and battery tray (C).
2. Remove the protective cap from the battery terminal.
3. Use a 12 volt battery charger to charge the battery (A).
Charge at a rate of 6 amperes for one hour. If you do
not have a battery charger, have an authorized service
centre charge the battery.
4. Install the battery (A) and battery tray (C). Make sure
the positive (+) terminal (D) is on the left side.
Not for
Reproduction
16 www.victa.com
How To Install The Battery Cables (Figure 4)
WARNING: To prevent sparks, fasten the red cable
to the positive (+) ter minal before you connect the
black cable.
1. Remove the protective caps from the battery terminals.
2. Slide the terminal cover (B) onto the red cable (E).
Fasten the red cable (E) to the positive (+) terminal
(D) with the fasteners (F) and (G).
3. Fasten the black cable (H) to the negative (-) terminal
with the fasteners (F) and (G).
Important! Before You Start Mowing
• Check the engine oil.
• Fill the fuel tank with fuel.
• Check the air pressure of the tires.
• Check the level of the mower hous ing.
• Attach the battery cables.
Check The Tires
Check the air pressure in the tires. Tires with too much air
pressure will cause the unit to ride rough. Also, the wrong
air pressure will keep the mower housing from cutting level.
The correct air pressure is: Front Tires 0,97 BAR (14 PSI),
Rear Tires 0,69 BAR (10 PSI). The tires were over inflated
for shipment.
Check The Level Of The Mower Housing
Make sure the level of cut is still correct. After you mow a
short distance, look at the area that was cut. If the mower
housing does not cut level, see the instructions on “How To
Level The Mower Housing” in the Maintenance section of
this instruction book.
How To Prepare The Engine
Check the oil and fuel levels, and add as needed.
IMPORTANT: Some units are shipped from the factory
without oil in the engine. It is important to check the engine
oil level before attempting to start or operate the unit. If you
start the engine without oil, it will be damaged beyond repair
and will not be covered under warranty.
See the "Operation" section of this manual for the type of
fuel and oil to use. Before you operate the unit, read the
information on safety, oper ation, maintenance, and storage.
WARNING: Follow the instructions in this manual
for the type of fuel and oil to use. Always use a
safety fuel container. Do not smoke when adding
fuel to the engine. When inside an enclosure, do
not fill with fuel. Before you add fuel, stop the
engine. Let the engine cool for at least three
minutes.
Assembly
Not for
Reproduction
17
Features and Controls
Location of Controls - Gear Drive Models
(Figure 5)
Blade Rotation Control (A) — Use the blade rota tion control
to start and stop the rotation of the blade.
Clutch / Brake Pedal (B) — The pedal has two functions.
The first function is a clutch. The sec ond function is a brake.
Headlight Switch (C) — The headlight switch is the first
part of the ignition switch. To use the lights with the engine
running, turn the key to the position for the lights.
Ignition Switch (C) — Use the ignition switch to start and
stop the engine.
Shift Lever (D) — Use the shift lever to change the speed or
direction of the unit.
Lift Lever (E) — Use the lift lever to change the height of
cut.
Parking Brake Lever (F) — Use the parking brake lever to
engage the brake when you leave the unit.
Throttle Control Lever (G) — Use the throttle control lever
to increase or decrease the speed of the engine.
NOTE: Illustrations and pictorials begin on page 3.
Location of Controls - Hydro-Drive Models
(Figure 6, 19)
Blade Rotation Control (A) — Use the blade rota tion control
to start and stop the rotation of the blade.
Brake Pedal (B) — Use the brake pedal to quickly stop.
Headlight Switch (C) — The headlight switch is the first
part of the ignition switch. To use the lights with the engine
running, turn the key to the position for the lights.
Ignition Switch (C) — Use the ignition switch to start and
stop the engine.
Speed Control Pedal (D) — Use the speed con trol pedal to
change the speed and the direction of the unit.
Lift Lever (E) — Use the lift lever to change the height of
cut.
Parking Brake Lever (F) — Use the parking brake lever to
engage the brake when you leave the unit.
Throttle Control Lever (G) — Use the throttle control lever
to increase or decrease the speed of the engine.
(Figure 19) Automatic Drive Disconnect (A) — Use the
automatic drive disconnect to disengage the transmission.
Attachments
This unit can use many different attachments. This unit
can pull attachments like a lawn sweeper, a lawn aerator,
or a hopper spreader. This unit can not use attachments
that engage the ground like a plough, a disk harrow, or a
cultivator.
For trailer and pull-behind attachments, the maximum weight
is 113 kg (250 lbs.).
Not for
Reproduction
18 www.victa.com
Operation
Before Operating
Check/Add Engine Oil
IMPORTANT: Some units are shipped from the factory
without oil in the engine. It is important to check the engine
oil level before attempting to start or operate the unit. If you
start the engine without oil, it will be damaged beyond repair
and will not be covered under warranty.
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF, SG,
SH, SJ or higher. Do not use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
* Below 40°F (4°C) the use of SAE 30 will result in hard
starting.
** Above 80°F (27°C) the use of 10W-30 may cause
increased oil consumption. Check oil level more frequently.
How To Check/Add Oil (Figure 7)
Before adding or checking the oil
• Place the unit on a level surface.
• Clean the oil fill area of any debris.
1. Raise the tractor hood.
2. Remove the dipstick (A) and wipe with a clean cloth.
3. Insert and tighten the dipstick.
4. Remove the dipstick and check the oil level. It should
be at the top of the full indicator (B) on the dipstick.
5. If low, add oil slowly into the engine oil fill (C). Do
not overfill. After adding oil, wait one minute and then
recheck the oil level.
6. Replace and tighten the dipstick.
Add Fuel
Fuel Recommendations
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). High
altitude use, see below.
• Gasoline with up to 10% ethanol (gasohol) is
acceptable.
CAUTION: Do not use unapproved gasolines, such as E15
and E85. Do not mix oil in gasoline or modify the engine
to run on alternate fuels. This will damage the engine
components and void the engine warranty.
To protect the fuel system from gum formation, mix a
fuel stabilizer into the fuel. See Storage. All fuel is not the
same. If starting or performance problems occur, change
fuel providers or change brands. This engine is certified to
operate on gasoline. The emissions control system for this
engine is EM (Engine Modifications)
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85
octane/85 AKI (89 RON) gasoline is acceptable. To remain
emissions compliant, high altitude adjustment is required.
Operation without this adjustment will cause decreased
performance, increased fuel consumption, and increased
emissions. See a Briggs & Stratton Authorized Dealer for
high altitude adjustment information.
Operation of the engine at altitudes below 2,500 feet (762
meters) with the high altitude kit is not recommended.
How To Add Fuel (Figure 8)
WARNING: Fuel and its vapors are extremely
flammable and explosive. Fire or explosion can
cause severe burns or death.
When Adding Fuel
• Turn engine off and let engine cool at least 3 minutes
before removing the fuel cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. To allow for expansion of the
fuel, do not fill above the bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap, and fittings frequently for
cracks or leaks. Replace if necessary
• If fuel spills, wait until it evaporates before starting
engine.
Not for
Reproduction
19
Operation
1. Raise the tractor hood.
2. Clean the fuel cap area of dirt and debris. Remove the
fuel cap.
3. Fill the fuel tank (A) with fuel. To allow for expansion
of the fuel, do not fill above the bottom of the fuel tank
neck (B).
4. Reinstall the fuel cap.
Operation - Gear Drive Models
Using Controls
How To Use The Throttle Control (Figure 5)
Use the throttle control (G) to increase or de crease the
speed of the engine.
1. The FAST position is marked with a detent. For normal
operation and when using a grass bagger, move the
throttle control to the FAST position. For maximum
charging of the battery and for a cooler running engine,
oper ate the engine in the FAST position.
2. The engine governor is set at the factory for maximum
performance. Do not adjust the governor to increase
the speed of the en gine.
How To Use The Blade Rotation Control (Figure 5)
Use the blade rotation control (A) to engage the blade(s).
1. Before you start the engine, make sure the blade
rotation control (A) is in the DISEN GAGE position.
2. Move the blade rotation control (A) to the ENGAGE
position to rotate the blade(s).
NOTE: If the engine stops when you en gage the
blade(s), the seat switch is not activated. Make sure
you sit in the middle of the seat.
3. Move the blade rotation control (A) to the DISENGAGE
position to stop the blade(s). Before you leave the
operator’s position, make sure the blade(s) has stopped
rotating.
4. Before you ride the unit across a sidewalk or a road,
move the blade rotation control (A) to the DISENGAGE
position.
WARNING: Always keep your hands and feet away
from the blade, deflector opening, and the mower
housing when the engine runs.
How To Use The Shift Lever (Figure 5)
CAUTION: Before you move the shift lever, completely
push the clutch/brake pedal for ward to stop the unit. If the
unit is not stopped, the gearbox can be damaged.
1. Completely push the clutch/brake pedal (B) forward to
stop the unit. Keep your foot on the pedal.
2. Move the throttle control lever (G) to the SLOW
position.
3. To go forward, move the shift lever (D) to a forward
speed setting. To go backward, move the shift lever
(D) to reverse.
4. Slowly release the clutch/brake pedal (B). Do not keep
your foot on the pedal.
5. Move the throttle control (G) to the FAST position.
How To Use The Parking Brake (Figure 5)
1. Completely push the clutch/brake pedal (B) for ward.
2. Lift and hold the parking brake lever (F).
3. Remove your foot from the clutch/brake pedal (B) and
then let go of the parking brake lever (F). Make sure
the parking brake will hold the unit.
4. To release the parking brake lever (F), completely push
the clutch/brake pedal (B) forward. The park ing brake
will automatically release.
WARNING: Before you leave the operator’s
position, move the shift lever to the neutral (N)
position. Set the parking brake. Move the blade
rotation con trol to the DISENGAGE position. Stop
the engine and remove the ignition key.
How To Change The Cutting Height (Figure 5)
To change the cutting height, raise or lower the lift lever (E)
as follows.
1. Move the lift lever (E) forward to lower the mower
housing and back to raise the mower housing.
2. When you ride on a sidewalk or road, move the lift
lever (E) to the highest position and move the blade
rotation control (A) to the DIS ENGAGE position.
Not for
Reproduction
20 www.victa.com
Operation
How To Stop The Unit (Figure 5)
1. Completely push the clutch/brake pedal (B) forward to
stop the unit. Keep your foot on the pedal.
2. Move the blade rotation control (A) to the DISENGAGE
position.
3. Move the shift lever (D) to the NEUTRAL position.
4. Set the parking brake (F).
WARNING: Make sure the parking brake will hold
the unit.
5. Move the throttle control (G) to the SLOW position.
6. To stop the engine, turn the ignition key (C) to the OFF
position. Remove the key.
How To Transport The Unit
1. Move the blade rotation control to the DIS ENGAGE
position.
2. Raise the lift lever to the highest position.
3. Move the throttle control to a position be tween SLOW
and FAST.
4. To go faster, move the shift lever to a faster speed.
Mowing
How To Operate With The Mower Housing
IMPORTANT: When you operate with the mower housing,
always operate with the throttle control in the FAST position.
1. Start the engine.
2. Move the lift lever to a height of cut position. In high or
thick grass, cut the grass in the highest position first
and then lower the mower housing to a lower position.
3. Move the throttle control to the SLOW posi tion.
4. Slowly move the blade rotation control to the ENGAGE
position.
5. Push the clutch/brake pedal completely for ward.
6. Move the shift lever to one of the speed set tings.
NOTE: When you mow in heavy grass or mow with a
bagger, put the shift lever in the slowest speed.
7. Slowly release the clutch/brake pedal.
8. Move the throttle control to the FAST posi tion. If you
need to go faster or slower, stop the unit and move the
shift lever to another speed setting.
9. Make sure the level of cut is still correct. After you
mow a short distance, look at the area that was cut.
If the mower housing does not cut level, see the
instructions on “How To Level The Mower Housing” in
the Maintenance section.
WARNING: For better control of the unit, select a
safe speed.
How To Operate On Hills
WARNING: Do not ride up or down slopes that are
too steep to back straight up. Never ride the unit
across a slope.
1. Before you ride up or down a hill, move the shift lever
to the slowest speed.
2. Do not stop or change speed settings on a hill. If you
must stop, quickly push the clutch/brake pedal forward
and set the parking brake.
3. To start again, make sure the shift lever is in the
slowest speed. Move the throttle control to the SLOW
position. Slowly release the pedal.
4. If you must stop or start on a hill, always have enough
space for the unit to roll when you release the brake
and engage the clutch.
5. Be very careful when you change directions on a
hill. When on a slope or in a turn on a hill, move the
throttle control to the SLOW position to help prevent an
accident.
Starting the Engine
NOTE: This unit is equipped with a safety interlock system
that includes a sensor switch for the seat. This system will
stop the engine when the operator leaves the seat. For your
protection, always make sure this system operates correctly.
NOTE: The engine will not start unless you sit in the seat,
depress the clutch/brake pedal, and move the blade rotation
control to the DISENGAGE position.
1. Check oil and fuel levels, and add as needed.
2. Push the clutch/brake brake pedal complete ly forward.
Keep your foot on the pedal.
3. Move the shift lever to the neutral (N) position.
4. Make sure the blade rotation control is in the
DISENGAGE position.
5. Move the throttle control completely forward past the
FAST position to the CHOKE position.
NOTE: The CHOKE position is usually unnecessary
when restarting a warm engine.
6. Turn the ignition key to the START position.
NOTE: If the engine does not start after four or five
tries, see the Troubleshooting section.
7. Slowly move the throttle control to the FAST position.
8. To stop the engine, turn the ignition key to the OFF
position. Remove the key.
Not for
Reproduction
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Simplicity 2691004 User manual

Category
Lawnmowers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI