Eneo HDB-2180Z03IR Operating instructions

INSTALLATION AND OPERATION MANUAL

for

HDD-2080MIR

1

Table of contents

1. Safety Instructions and Notes….......................................................................................................

2. General Descriptions............................................................................……………………………...

3. Supplied Items......................................................................................……………………………...

4. Part names…………………………….…...................................................…………………………...

5. Installation Instructions......................................................................................……………………...

6. Setup Menu ……………............................................................................…………………………...

7. Specifications ………………………………………………..................................................................

8. Dimensional Drawings ……………………………………………............................................................

3

4

5

6

10

22

23

2

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of

uninsulated "dangerous voltage" within the product's enclosure that

may be of sufficient magnitude to constitute a risk of electric shock

to persons.

Warning(NTSC version) -- This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Caution -- Any changes or modifications in construction of this device which are not expressly approved by

the party responsible for compliance could void the user's authority to operate the equipment.

Mains power quality should be that of a typical commercial environment. If the user of the model requires

continued operation during power mains interruptions, it is recommended that the model be powered from

an uninterruptible power supply (UPS) or a battery.”

Notice -- The images used in manual are processed to help comprehension and may

differ from actual video of the camera.

WARNING

NEVER USE THIS CAMERA

1. IN AREA WHERE HAS SHOCK OR VIBRATION WHICH RESULTS IN THE

PROBLEM.

Caution

To prevent electric shocks

and risk of fire hazards, do

NOT use other than specific

power source.

WARNING

3

1. Safety Instructions and Notes

• Please read this safety and operating instructions before putting the camera into operation.

• Keep the manual in a safe place for later reference.

• Pay attention to safety when laying the connection cable and observe that the cable is not subjected to

heavy loads, kinks or damage and no moisture can get in.

• Never open the device such as boards or lens.

The warranty becomes void if repairs are undertaken by unauthorized persons.

• Maintenance and repair have to be carried out only by authorized service centers.

• Use only a mild detergent to clean the housing.

• The camera should never be operated beyond the technical specifications. This can lead to destruction.

• The camera should never be operated in the water.

2. General Descriptions

FULL HD WDR HD-SDI CAMERA, 1920 x 1080/30p(25p)

Highly detailed pictures can be achieved and color reproducibility deserves attention

With ICR mechanism,

- Enhances its sensitivity about 10x at night time

- Can accepts the infrared light

With Intelligent Focus Indicator and FOCUS ADJUST menu,

- Offers easy adjustment of Focus

- Eliminates the mistake of the erratic focus adjustment

With 24VAC/12VDC dual power design,

- Offers the flexibility of installation

- Ensures the reliability

Main features are;

• Full HD, 1920 x 1080/30p(25p)

• True Wide Dynamic Range

• DUAL Filter Switcher – No Focus Shift at Night.

• Day & Night Simulation

• Built-in Mega Pixel Vari-focal Lens (f=2.8~10mm)

• Non Compression digital streaming up to 1.485Gbps

• Intelligent Focus Status Indicator on Screen

• Pointing Zoom which enables the flexible zooming at any area.

• Smart Motion Zoom in combining with Pointing Zoom.

4

• Scale down the image to 720p without loss of field of view

• Top performance at low light sensitivity (Sense-up On)

• Improved Noise figure with the enhanced 3D-NR

• D-WDR, BLC/HLC, Digital Zoom(1.1x~8x)

• Motion Detect, Privacy Mask, Anti-Fog, Sense-up(x8)

• LSC(Lens Shade Compensation)

• RS-485(Pelco-D)

• OSD MENU & CVBS Video Sub-out port for easy installation & Maintenance

• Circuit protection against faulty connection.

• Isolated power supply against ground loop problem.

• Hard coated polycarbonate clear Bubble

• Surface / flush mount available

• 3-Axis gimbal

• Zoom & Focus Adjustment on gimbal

• IP 68 / IK 10 Protection

• 30 LEDs

3. Supplied Items

• 1x Vandalproof Dome camera

• 1x Installation and Operating Instructions

• 1x ①Pipe hole cap

• 1x ②Pipe Spacer

• 1x ③L-shape hex wrench

• 1x ④Focus Adjust Driver

• 3x ⑤Wrench Bolt for surface mount

• 4x ⑥Anchors

• 4x ⑦Mount screws

• 1x ⑧BM Screw

• 1x ⑨Sub-out cable

5

4. Control and Part names

ⓐ Zoom & Focus

ⓑ

Lens hood

ⓒ

Light sensor for IR LEDs

ⓓ

IR LEDs

ⓔ

Dome base

ⓕ

Mount holes(x3) for dome base

ⓖ

OSD control joy stick

ⓗ

Video Sub-output

ⓘ Clear bubble

ⓙ Ring cover fixing screws(x3)

ⓚ

Ring cover

ⓛ Pipe hole

ⓜ Dome base fixing screw taps(x3)

ⓝ Surface mount holes(x4)

ⓐ

ⓑ

ⓒ

ⓓ

ⓔ

ⓖ

ⓕ

ⓗ

Dome base assembly

ⓝ

ⓜ

ⓛ

Surface Mount Base

ⓘ ⓙ ⓚ

Dome Bubble Assembly

6

5. Installation

5.1 Surface mount

Surface mount base

⑦Mount screws

and ②pipe hole

cap for surface

mount base

Dome base

assembly

⑤Wrench bolts

for fitting to

surface mount

base

Dome bubble

assembly

L-Wrench

Quick installation guides;

1. Locate the mounting template at the installation position

and drill the ceiling or wall if needed.

2. Place Surface mount base on pre-drilled position and fix it

through ⓝSurface mount holes(x4) by using ⑦Mount screws.

Assemble the cable pipe, otherwise tighten ①pipe hole cap.

3. Open Dome bubble assembly by loosening ⓙRing cover

fixing screws(x3)

CAUTION

Extreme care should be taken NOT to scratch the dome

surfaces and to protect it from dirt or dust at any time.

4.

ⓕ

Mount holes(x3) for dome base and

ⓜ

hole should be

aligned before fixing Dome base assembly to Surface mount

base by using ⑤Wrench bolts. And tighten ⑤wrench bolts

5. Route the power/ video cable to the connecting place.

CAUTION

Care should be taken the cable is NOT to be damaged,

kinked or exposed in the hazardous area.

6. Set the camera’s angle (Pan, Tilt, inclination)

7. Adjust

ⓐ

Zoom & Focus by using ④focus adjust driver.

8 Put Dome bubble assembly over Dome camera assembly and

tighten ⓙRing cover fixing screws(x3) by using ③L-shape hex

wrench

CAUTION

Tighten enough

ⓙ

Ring cover fixing screws(x3) so that

there should be NO gap between

ⓑ

Lens hood and

ⓘ

Clear bubble to avoid the light inflow from IR LEDs.

Ceiling or wall

7

5.2 Flush mount

⑦Mount screws

Dome base

assembly

Dome bubble

assembly

L-Wrench

Quick installation guides;

1. Locate the mounting template at the installation position

and drill the ceiling or wall if needed.

2. Open Dome bubble assembly by loosening ⓙRing cover

fixing screws(x3)

CAUTION

Extreme care should be taken NOT to scratch the dome

surfaces and to protect it from dirt or dust at any time.

3. Place Dome base assembly on pre-drilled position and fix it

through

ⓕ

mount holes(x3)

by using ⑦Mount screws.

(Use three screws only out of ⑦Mount screws(4x))

4. Route the power/ video cable to the connecting place.

CAUTION

Care should be taken the cable is NOT to be damaged,

kinked or exposed in the hazardous area.

5. Set the camera’s angle (Pan, Tilt, inclination)

6. Adjust

ⓐ

Zoom & Focus by using ④focus adjust driver.

7. Put Dome bubble assembly over Dome camera assembly and

tighten ⓙRing cover fixing screws(x3) by using ③L-shape hex

wrench

CAUTION

Tighten enough

ⓙ

Ring cover fixing screws(x3) so that

there should be NO gap between

ⓑ

Lens hood and

ⓘ

Clear bubble to avoid the light inflow from IR LEDs.

Ceiling or wall

8

5.3. Setup of the Zoom and FOCUS

• Remove the dome bubble assembly and power up the camera.

• Adjust

ⓐ

Zoom setting using ④focus adjust driver.

• Adjust

ⓐ

Focus setting using ④focus adjust driver.

• Close the dome bubble assembly and tighten ⓙRing cover fixing screws(x3) using ③L-shape hex wrench.

Tips for the precise adjustment of lens at outside

1. It is recommended to place a ND (Neutral Density) filter in front of the lens.

This results the lens iris open and narrow depth of field and allows the precise focus adjustment.

2. When ND filter is NOT available, follow the process carefully.

CAUTION : This process is a little complicated and requires 'MUST FOLLOW THE STEPS'.

1) Enter SETUP menu.

2) Select MANUAL at MAIN menu-1>LENS .and Exit SETUP menu.

3) Adjust

ⓐ

Zoom & Focus.

4) Enter SETUP menu again.

5)

Restore FACTORY DEFAULT

by MAIN menu-2>CAMERA RESET (See 7.15 CAMERA RESET).

6)

Save the restored parameters

by moving cursor to SAVE ALL and pressing ● button.

7) Set all other functions if necessary.

8)

Save the changes

by moving cursor to SAVE ALL and pressing ● button.

9) Exit SETUP menu

5.4 Limit of pan and tilt

1. Pan limit

Pan is limited to +/- 165°.

Do NOT force to rotate the gimbal over the limit to prevent from the internal damage.

2. Tilt limit

Tilt is limited to 25° min ~ 90° max. with reference to the ceiling when the inclination of camera module

is 0°, that is, the image is aligned horizontally.

CAUTION Tilt may NOT reach 25° min. if some IR light reflects to the lens when the inclination is NOT 0°.

When Tilt is set to near the minimum limit, examine and verify that NO IR refection occurs.

3. Inclination limit (Horizontal image alignment)

Inclination limited to +/-60° max.

9

5.5 Power connector

Camera can work with either 24AC or 12VDC, dual voltage power.

It is strongly required the polarity-matched connection for 12VDC supply,

otherwise IR LEDs will not operate at night.

Primary and secondary grounds are completely isolated to avoid the possible ground-

loop problems.

In case that HD-SDI Inputs are not supported in Monitor, please use HD-SDI Converter

to connect HD-SDI cable with Monitor.

Some monitors for PC purpose in the market may not support 30p/25p and cannot

display picture. Please check Specification of Monitor before installation.

AC24V/DC12V (RED WIRE)

AC24V/GND (BLACK WIRE)

HD-SDI CABLE

RS-485

10

6. Setup Menu

6.1 Camera setup in the menu

Setup menu can be accessed and controlled by OSD control joy stick on the side of camera.

Five commands are available with the joy stick.

The design of OSD could be different according to the Model.

In the menu,

use ▲,▼ to move menu, ◀,▶ to change the settings and press

☟

to select or enter.

FACTORY DEFAULT values in this manual may NOT be the same as the default values by FACTORY

SET due to the changes for the improvements or the customer's requirements

.

Joy stick

VIDEO

SUB-OUT

connector

SYMBOL descriptions for joystick operation;

-▲,▼,◀,▶ denotes the directions of

Joystick lever operation.

-

☟

denotes Pressing straight down of

Joystick lever

Example of OSD controller

▲ D-Zoom In

▼ D-Zoom Out

Digital Zoom Adjustment

(Only works when OSD Menu is not operating)

11

6.2 MAIN menu

Press ● to enter the setup menu for about 1 second.

MENU V3.07

1. EXPOSURE

2. LENS

3. FOCUS ADJ.

4. SCENE ENHANCE

5. 3D-NR

6. DAY/NIGHT

7. PICT ADJUST

8. SPECIAL

9. SYSTEM

A. EXIT

↵

DC

↵

NORMAL

MID

AUTO

↵

SAVE&EXIT

MAIN Default Descriptions

EXPOSURE

Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP and AGC.

See ‘6.3 EXPOSURE’ for detail.

LENS DC Sets Lens type and See ‘6.4 LENS’ for detail.

FOCUS ADJ See ‘6.5 ZOOM/FOCUS’ for detail.

SCENE

ENHANCE

NORMAL

NORMAL – Optimized for the normal indoor and outdoor in the good

lighting condition.

WDR – Improves the visibility for the high bright area and the dark area

by the double captures of image with LONG and SHORT exposures.

With WDR ON, the frame rate becomes half by the double captures.

WDR level can be selected from LOW, MID and HIGH.

Care should be taken to select this mode because video may lose its

quality in some environments by the over compensation.

※CVBS video signal - Even if WDR is set to ON, it shows OFF on CVBS

video. It should be considered when installer adjusts the video with

installation monitor.

D-WDR – Improves the visibility by compensating the video gain for the

dark area. Noise can increase in the dark area accordingly.

BLC – Improves the visibility for the dark object by the bright back light.

Outside area of BLC window can over saturate.

BLC has a target window for compensation and its size and position

can be set by H-POS, V-POS, H-SIZE and V-SIZE.

HLC – Cuts out the highlight area with black mask and excludes it from

compensation. Lower HLC LEVEL cut out video from the lower level.

12

3D-NR MID

Enables to set OFF, LOW, MID and HIGH.

3D-NR is a very sophisticated and powerful time-based noise reduction

technology by monitoring the noise for the several video frames and defining

and eliminating them consecutively at low light.

Higher setting reduces noise much more but results in losing the sharpness

and the tail effect or the motion blur for the fast moving target at low light.

DAY/NIGHT EXT

Sets DAY / NIGHT to EXT, AUTO, COLOR and B/W.

SMART IR can be set to reduce the saturation by the strong IR illumination

in the night in any menu of EXT, AUTO and B/W(NIGHT)

Setting SMART IR in any menu is identically applied to other menu.

Zero(0) turns off SMART IR and High setting avoids the saturation strongly

but the corners will be darker accordingly.

Installation surrounding lots of IR LEDs ON is not recommendable.

The Light of IR LEDs may cause unwanted and frequent

Day & Night Filter switching and it affects the lifetime of IR Cut Filter.

In case of installation at lots of IR LEDs ON,

change the Day & Night mode to COLOR(DAY).

EXT – DAY or NIGHT is determined by the built-in light photo sensor.

Camera with IR LED must be set to EXT.

AUTO – Used when DAY or NIGHT is determined by light level through

the lens and DAY from/to NIGHT is switched automatically by the

scene brightness.

D<-->N THRESHOLD, D<->N GAP, D<->N DELAY, and SMART IR can

be set in the menu.

When EXPOSURE>AGC is less than 10, DAY/NIGHT AUTO is disabled and

forcibly switches to ___(DAY) to avoid the malfunction.

EXT, B/W(NIGHT) and COLOR(DAY) is independent on AGC level.

B/W(NIGHT) – Forcibly removes IR cut filter and switches to B/W

regardless of light level.

COLOR(DAY) – Forcibly DAY/NIGHT is disabled and outputs color video.

PICT ADJUST

Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA, SHADING.

See ‘6.7 PICT ADJUST’ for detail.

SPECIAL

Sets MIRROR/FLIP, PRIVACY, MOTION, MOTION ZOOM, PIXEL DEFECT,

TITLE SET, DISPLAY, DEFOG, POINTING ZOOM

TV SYSTEM. See ‘6.8 SPECIAL’ for detail.

SYSTEM

Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE and

FACTORY DEFAULT.

EXIT

SAVE & EXIT – Exits the menu after saving the parameters.

EXIT – Exits the menu without saving the menu.

13

6.3 EXPOSURE

EXPOSURE

SHUTTER

BRIGHTNESS

SENS-UP

AGC

RETURN

AUTO

|:::::::|::::::| 10

OFF

|::::::::|:::::| 12

RET

↵

2x

EXPOSURE Default Descriptions

SHUTTER AUTO

Can set EXPOSURE MODE to AUTO, MANUAL and Flickerless.

AUTO – Optimizes the video level by controlling the iris and the shutter speed

automatically.

MANUAL – Iris and Shutter can be set to fix.

Flickerless – Reduces the flicker in video when US(60Hz)/EU(50Hz)

mode is used in 50Hz/60Hz fluorescent lighting respectively.

MANUAL and Flickerless modes disable SENS-UP and MOTION BLUR

functions.

BRIGHTNESS 10

Adjusts the brightness of video(0~20).

SENS-UP OFF

The brighter video can be obtained by increasing the exposure time in the

night with SENS-UP.

SENS-UP is the maximum integrations of frame by DSS(Digital Slow Shutter)

in the low light.

AUTO – SENS-UP(x2~x8) is enabled or disabled automatically by the scene

brightness. Higher SENS-UP can get the brighter video but the

slower frame rates with motion blur and more white pixels.

OFF – Disables SENS-UP.

AGC 12

AGC(0~20) amplifies the video gain for brighter video but noise and white

pixel accordingly.

AGC level less than 10 disables AUTO in DAY/NIGHT.

14

6.4 LENS

DC

MODE

RETURN

OUTDOOR

RET

↵

MANUAL

MODE

RETURN

DEBLUR

RET

↵

Lens Default Descriptions

DC

or

MANUAL

OURDOOR

Lens can be selected either DC or MANUAL lens.

Lens MUST be set to DC for the best image when DC iris lens is installed.

DC or MANUAL- OUTDOOR, INDOOR, DEBLUR

Select lens mode according to installation place.

Select INDOOR or DEBLUR for indoor installation according to

environment.

DEBLUR enables to reduce the blur in a certain indoor environment.

Noise or color rolling can increase.

Horizontal wave or bar may be seen when MANUAL is selected and the

camera is working under florescent or similar lights.

15

6.5 FOCUS ADJ.

FOCUS ADJ.

DN DWELL

POP ON FOCUS

RETURN

5s

OFF

RET

↵

FOCUS ADJ. Default Descriptions

DN DWELL 5s

ICR switcher switches DAY & NIGHT at the interval of D/N DWELL

to help the EXACT NIDDLE focus at DAY and NIGHT mode.

Further simulations are performed internally during switching.

POP ON FOCUS

OFF

ON zooms in the center of picture at 2X for better focusing.

FOCUSING

STATUS

ON

Shows how exactly focus is set.

When blue bar doesn’t show up, try the lens focus to NEAR and FAR.

The maximum blue bar indicates the best focusing position.

FOCUSING STATUS

Usually cameras are installed in the day time and

they often become OUT OF FOCUS at night time

and IN FOCUS again at next day time.

This problem can occur at any cameras regardless

of types or manufacturers.

FOCUS ADJ. menu is the unique and patented

feature that prevents from the wrong focus and

helps the EXACT NEEDLE focus by simulating

DAY & NIGHT conditions.

Set zoom first and adjust focus to get NEEDLE

FOCUS while switching AT DAY AND NIGHT

16

6.7 PICT ADJUST

PICTURE

WHITE BAL

SHARPNESS

COLOR GAIN

GAMMA

SHADING

RETURN

ATW

|:::::::|::::::| 10

0.50

OFF

RET

↵

PICTURE Default Descriptions

WHITE BAL ATW

ATW, ATWext, ONE PUSH and MANUAL are available for the white balance

modes.

ATW – White balance is continuously working along with the color

temperature changes in the range of 2,000K~8,500K.

ATWext – White balance is continuously working along with the color

temperature changes in the range of 1,800K~11,000K.

ONE PUSH- White balance works only during ● is pressed.

MANUAL – White balance is fixed to the settings by R_GAIN and

B-GAIN. This mode can be used only when the color temperature

does not vary.

SHARPNESS 10 Adjusts the sharpness of video(0~20).

COLOR GAIN 10 Adjusts the color level of video(0~20).

GAMMA 0.50 Adjusts the gamma of video.

SHADING OFF ON enables to compensate the shade caused by wide lens setting

17

6.8 SPECIAL

PICTURE

MIRROR/FLIP

PRIVACY

MOTION

PIXEL DEFECT

TITLE SET

DISPLAY

DEFOG

POINTING ZOOM

RETURN

OFF

↵

OFF

RET

↵

SPECIAL Default Descriptions

MIRROR/FLIP OFF

Reverses the video left and right and/or up and down by MIRROR/FLIP.

OFF - Normal display without mirroring or flipping

Hor. – Video is reversed left and right.

Ver. – Video is reversed upside down.

HV – Video is reversed left and right and upside down.

When the video is reversed by Ver. or HV, then the joystick directions are

reversed accordingly. This feature is very useful when a camera in installed in

upside dawn.

PRIVACY OFF

10 Privacy zones which can be enabled individually by ZON DISP are available

to mask the video.

ZONE NUMBER – Set a number to select a privacy zone from 1~10.

ZONE DISP – ON enables a relevant privacy zone.

H-POS, V-POS, H-SIZE and V-SIZE – Adjust the size and position of zone.

COLOR – Select the color used for masking the zone form eight colors(1~8).

TRANSPARENCY – Enables to set OFF, 50%, 75%, 100%.

Defines the transparency for the mask zone.

MOTION OFF

MOTION can detect the changes in the motion window and displays the results

in blocks and/or a text message.

SENSITIVITY – Adjusts the detection sensitivity for motion.

High value increases the sensitivity to detect the small motion easily.

Too low sensitivity will cause the erratic detection by the tree leaves

or the light level changes.

H-POS,V-POS, H-SIZE and V-SIZE - Adjust the size and position of

the detection window.

BLOCK DISP – ON enables to display the blocks for the detected area.

MOTION OSD – ON enables to display a text message, ‘MOTION’,

SMART MOTION ZOOM – ON activates Automatic Zoom IN/OUT when motion

is detected.

Area to be zoomed in by SMART MOTION ZOOM can be set at SPECIAL>

MOTION> SMART MOTION ZOOM.

Adjusting◀,▶(Joystick) varies the viewing angle to be zoomed when the

motion occurs. See ‘6.8.1 SMART MOTION ZOOM’ for detail.

STAY ZOOMING – Sets the duration time for zooming by Motion.

18

PIXEL DEFECT OFF

Detects and compensates the white pixels which becomes defective.

Once CALIBRATE is selected, the pixel calibration is initiated with lens closed

and can’t cancel.

THRESHOLD – Defines the level of detection and low value detects more

pixels. Be sure to set the value so that the pixels are uniformly blinking

over the entire screen. Too low value will get the bad results because

too many pixels are detected as the bad pixels and the maximum

number of pixels for compensation will be filled by the upper area.

EXECUTE

☟

- Long pressing will execute the pixel calibration for the

detected pixels. Menu will exit automatically after compensation.

TITLE SET -

Camera title(name) can be set and edited up to 15 alpha numeric and symbolic

characters from ASCII codes(ENGLISH only).

▲,▼,◀,▶ moves the cursor to choose a character and

● selects it.

The selected characters are added and displayed on the top left

Corner and the cursor moves right automatically for next input.

SP - Space is inserted when pressed ●.

BS – Cursor moves back when pressed ●.

CLR – Clears all the characters on input line when pressed ●.

POS – To be able to set the title position by ▲,▼,◀,▶ and ●.

DISPLAY -

Enables or disables to display the OSD.

ID – ON enables to display the camera ID defined by SYSTEM>COMM.

SETUP>CAM ID.

TITLE – ON enables to display the camera title(name) set by SPECIAL>

TITLE SET.

D-ZOOM RATIO – ON enables to display the zoom ratio on the bottom right

corner. DZx.x will display by multiplying the actual digital zoom ratio.

DEFOG OFF

AUTO – Enhance the foggy video automatically according to

status of scene

MANUAL – Sets to enhance the foggy video manually regardless of

status of scene

LEVEL – LOW, MID, HIGH

Video quality can be less in normal environments.

POINTING

ZOOM

OFF

ON enables to set off-centered location to be the center of zoom

H-POINTER, V-POINTER- Able to set the location of zoom center

D-Zoom is available DZ X1.0~ X8.0.

See ‘6.8.2 POINTING ZOOM’ for detail.

19

6.8.1 SMART MOTION ZOOM

SMART MOTION ZOOM crops and enlarges the certain area defined by a yellow window to the full sized

image when the motion is detected in the black window.

SMART MOTION ZOOM window can be re-sized by adjusting D-ZOOM RATIO and moved by H-POINTER

and V-POINTER.

UNLIKE the conventional zoom which can zoom in/out the center area of image only, by the flexible zoom

location and area, SMART MOTION ZOOM differentiate its usefulness from others.

That is, a conventional camera installed on the corner of ceiling can zoom the center of the floor in a room

and result in losing the image of door on the side wall.

However, SMART MOTION ZOOM can be set to see the door side and zoom in that area without missing

the IMPORTANT security point.

SMART

MOTION ZOOM

Default Descriptions

H-POINTER 10 Moves MOTION ZOOM area(Yellow window) horizontally.

V-POINTER 10 Moves MOTION ZOOM area(Yellow window) vertically.

D-ZOOM

RATIO

MZ2.0 Sets the area size to be zoomed when the motion occurs in the black window.

SMART MOTION ZOOM

H-POINTER

V-POINTER

D-ZOOM RATIO

RETURN

10

MZ2.0

RET

↵

Page is loading ...

Eneo HDB-2180Z03IR Operating instructions

This manual is also suitable for

Eneo HDB-2180Z03IR Operating instructions

Related papers

Other documents