Acumen AiP-M34E-45Y0B User manual

Acumen
Brand
Acumen
Model
AiP-M34E-45Y0B
Category
Security cameras
Type
User manual

This manual is also suitable for

AirPlay All-Weather
Series
H.264 HD AiP cameras
INSTRUCTION MANUAL
Summary
The AiP AirPlay series includes Full HD IP cameras that adopt the latest compression
technologies providing Triple Streaming of H.264 and JPEG in different resolutions.
Acumen’s Triple Streaming technology transmits digital video at various bitrates and
frame rates to suit both high and low bandwidth network environments.
The AirPlay series cameras are equipped with progressive mega-pixel CMOS sensors
providing superior video quality. Acumen’s DSP technologies provide Wide Dynamic
Range (WDR), 3D noise reduction, Backlight Compensation (BLC), adjustable shutter
speed, and privacy mask features.
The built-in intelligent video analytics engine enables audio and motion detection. Other
useful features include two-way audio, SD card recording, mobile phone live access,
JPEGs sent as email snapshots, and JPEGs sent to an FTP.
The AirPlay series cameras have the latest technologies providing mega-pixel H.264
video, outstanding DSP capacities, built-in video analytics, and built-in PoE. All AirPlay
cameras are ONVIF compliant.
Acumen’s AiM HD software and IP cameras maximize system performance providing an
integrated system solution for migrating to IP Video.
1
Key Features
3Megapixel AiP camera capable of recording at 15 FPS
Supports dual encoding formats of H.264 and MJPEG
Quad Streaming technology, 4 concurrent streams available
MoonLight for low light conditions
Day or night video quality scheduling
Audio and motion detection for notification via email or FTP
Supports 3D DNR, WDR, BLC, adjustable shutter speed and privacy mask
Bitrate and frame rate adjustable on-the-fly
Supports Android, iPad, and iPhone mobile live monitoring
Supports dynamic DNS (DDNS) and network time protocol (NTP)
Supports ONVIF protocol
Supports AiM Software HD 2.6
Trademark Acknowledgments
Microsoft, Windows 2000, Windows XP, Windows Vista, Windows 7, ActiveX, and
Internet Explorer are registered trademarks of Microsoft Corporation in the U.S. and/or
other countries.
Java and all Java-based trademarks and logos are trademarks or registered trademarks of
Sun Microsystems, Inc. in the United States and other countries. Flash, Macromedia, and
Macromedia Flash Player are either trademarks or registered trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
Linux and DynDNS are registered trademarks of the respective holders.
Intel, Pentium, and Intel® Core™ 2 Duo are registered trademarks of Intel Corporation.
FFmpeg is a trademark of Fabrice Bellard, originator of the FFmpeg project.
QuickTime and the QuickTime logo are trademarks or registered trademarks of Apple
Computer, Inc., used under license there from.
Other names of companies and their products mentioned in this manual may be
trademarks or registered trademarks of their respective owners.
2
Other References
Mobile phone
For free mobile surveillance, refer to the eMobile document in the product CD
or download the document from our company website.
Acumen Universal ActiveX Control
Sample codes and documents are included in the product CD and can be downloaded
from our company website.
Acumen HTTP API
For non-ONVIF integration, please see the Acumen HTTP API document. We adopt
HTTP API document for all Acumen IP cameras.
Caution
Do not drop or strike the equipment
Do not install the equipment near any naked flames or heat sources
Do not expose this unit to rain, moisture, smoke or dust environments
Do not cover the opening of the cabinet with cloth and/or plastic or install this unit in
poor ventilated places. Allow 10cm between this unit and its surroundings
Do not continue to operate the unit under abnormal conditions such as smoke
detection, strange smell or no display on screen whilst power is turned on
Do not touch the power connection with wet hands
Do not damage the power cord or leave it under pressure
To avoid unnecessary magnetic interference, do not operate this unit near magnets,
speaker systems, etc.
All connection cables should be grounded properly
3
Table of Content
Chapter 1 System Overview ................................................... 6
Chapter 2 Before accessing IP cameras .......................................... 7
Chapter 2-1 Configuring IP addresses using IP scan utility ........................ 7
Chapter 2-2 Configuring IP addresses using HTML page ......................... 7
Chapter 2-3 Internet browser settings & software components required .............. 8
Chapter 2-4 Login ......................................................... 9
Chapter 3 H.264 Full HD IP camera network features ............................. 10
Chapter 3-1 IP Camera Operational HTML.................................... 10
Chapter 3-2 IP Camera Main Controls ........................................ 12
Chapter 3-2-1 Two-way Audio ........................................... 12
Chapter 3-2-2 Record in a Local PC ....................................... 12
Chapter 4 Basic Settings ..................................................... 13
Chapter 4-1 Configuration.................................................. 13
Chapter 4-2 System Settings ................................................ 13
Chapter 4-3 Timer ........................................................ 14
Chapter 4-4 Video / audio settings ........................................... 14
Chapter 4-4-1 Weighted Mode ........................................... 15
Chapter 4-5 Basic Quality .................................................. 16
Chapter 4-6 Network Settings ............................................... 16
Chapter 4-6-1 DHCP Setting ............................................. 17
Chapter 4-7 HTTP & RTSP Service .......................................... 17
Chapter 4-8 DDNS Settings ................................................ 18
Chapter 4-9 UPnP Settings ................................................. 18
Chapter 4-10 Maintenance ................................................. 19
Chapter 5 Advance Settings ................................................... 21
Chapter 5-1 System Settings ................................................ 21
Chapter 5-1-1 User Setting .............................................. 21
Chapter 5-1-2 System Log ............................................... 21
Chapter 5-2 Advance Video and Audio Settings ................................ 22
4
Chapter 5-2-1 Advance Video Setting ..................................... 22
Chapter 5-2-2 MoonLight ............................................... 23
Chapter 5-2-3 IR Cut Removable ......................................... 24
Chapter 5-2-4 Video Privacy Mask ....................................... 24
Chapter5-2-5 Audio Setting.............................................. 25
Chapter 5-3 IP Network Advance ............................................ 25
Chapter 5-4 Event ........................................................ 25
Chapter 5-4-1 Motion Alarm, or Audio Detection Event ...................... 26
Chapter 5-4-2 Motion Area .............................................. 26
Chapter 5-4-3 Audio Detection Event ..................................... 27
Chapter 5-4-4 Alarm Input Detection Event ................................ 27
Chapter 5-4-5 Network Loss Detection Event ............................... 28
Chapter 5-5 Notification ................................................... 28
Chapter 5-5-1 FTP Notification .......................................... 28
Chapter 5-5-2 SMTP Email Notification ................................... 29
Chapter 5-5-3 Event Triggering SD Card Recording ......................... 30
Chapter 5-5-4 SD Card Recording Setting .................................. 30
Appendix ............................................................... 31
Advance Network DDNS and PPPoE Technologies .......................... 31
SD Card Compatibility List .............................................. 31
Specification ............................................................. 32
5
Chapter 1 System Overview
Chapter 1-1 System Requirements
The IP camera’s Full HD H.264 video compression technology provides high
compression rate and superior video quality. However, the performance highly depends
on both the CPU computational power of the users PC and the network bandwidth for
transmitting video streaming. The following sections specify the system requirements for
running a Full HD H.264 IP camera.
Chapter 1-2 Software Requirements
Acumen 's Universal ActiveX software components are required for web interface
displaying JPEG or H.264 Full HD video. When you first login to the IP camera using
Internet explorer, a security warning dialog box will appear for Acumen Universal ActiveX.
Click “Install” to download.
6
Chapter 2 Before accessing IP cameras
Before accessing the IP camera, make sure that the camera’s RJ-45 network, audio, and
power cables are properly connected. To set the IP address, consult your network
administrator. The default IP address for each IP camera is 192.168.0.200. Users can use
the default IP address to verify the camera’s network connection.
Chapter 2-1 Configuring IP addresses using IP scan utility
To configure an IP address using the IP scan utility, copy the IP scan application from
the installation CD to your local PC. Alternatively, you can execute the IP scan software
from the installation CD directly. The IP scan utility can also be downloaded from our
company website. To change an IP address, subnet mask, gateway, or HTTP port, follow
the steps below:
Run the IP scan utility
Click “Refresh”. All available devices will be listed in the device list
Select the device item from the device list
To edit or modify addresses, subnet mask, gateway, or HTTP port, use the box
Click “Apply” to configure the settings
Click “Refresh” to verify the settings
Chapter 2-2 Configuring IP addresses using HTML page
To change an IP address using a HTML page, type the default IP address (192.168.0.200)
7
into the Internet browser and follow the steps below:
Login to the H.264 Full HD IP camera using default username “admin” and default
password “pass”
Click the “Basic Mode” configuration hyperlink
Click the “Network->General” hyperlink
To edit or modify addresses, subnet mask, gateway, or HTTP port, use the edit box
Click “Submit”
Chapter 2-3 Internet browser settings & software components required
Make sure your Internet browser allows signed ActiveX plug-in to run on your PC. Set
“Download Signed ActiveX plug-in controls” to “Prompt” and “Run ActiveX control
and plug-in” to “Enable”. You can set this by Internet Explorer->Tools->Options-
>Security Settings.
Once complete, you can access the IP camera’s live video by inserting the default IP
address into your Internet explorer browser. A security warning dialog box will
appear. Click “OK” to download the ActiveX directly from the IP camera.
8
Chapter 2-4 Login
There are several levels of user authentication including administrator and guest.
The usernames and passwords areas follows:
Administrator
Viewer
Username
admin
guest
Password
pass
guest
To login to the IP camera, type the username and password into the HTML login page
and click “Submit”.
9
Chapter 3 H.264 Full HD IP camera network features
When logged in as an administrator there are two main features; 1) system operation and
2) configuration.
Chapter 3-1 IP Camera Operational HTML
Page layout
3
1.
4
2.
1. Profile switching menu—Switching from one profile to another
2. Acumen Universal ActiveX control—Display RTSP H.264 or JPEG network
video
3. Quick button control panel—IP camera control panel
4. Setup menu—IP camera setup menu
10
Universal ActiveX control provides an ePTZ (electronic Pan, Tilt, and Zoom) feature
option. To perform a ePTZ tour, use a computer mouse to drag the ActiveX control.
The Acumen Universal ActiveX control is now in eZoom mode.
Use a computer mouse pointing to the sub-window of PIP view. Dragging the sub-
window will allow ePan and eTilt actions to be performed. The mouse scroll button
will allow the user to zoom in and out.
Right-mouse click on the video to disable the ePTZ feature.
11
Chapter 3-2 IP Camera Main Controls
The quick control panel buttons are described below:
Snapshot: Take a snapshot of the video
Recording at PC
Speaker on: Set audio on (for audio model only)
Microphone on: Speak to remote site (for audio model only)
Activate alarm output (for alarm model only)
Chapter 3-2-1 Two-way Audio
For models with two-way audio, click the microphone icon to speak to the
remote site. To stop speaking to the remote site, click the microphone icon again.
Click the speaker icon to listen to the remote site. To stop listening to the remote
site, click the speaker icon again.
Note: Only IP camera models with audio support this feature.
Chapter 3-2-2 Record in a Local PC
To record at a local PC, right-click on the Acumen Universal ActiveX control. You can
specify recording paths and recording sizes.
To playback the AVI video, click on Windows Media Player.
12
Chapter 4 Basic Settings
Chapter 4-1 Configuration
As an administrator, you can configure the IP camera via a standard HTML web page.
Chapter 4-2 System Settings
System settings contain the IP camera server system information including MAC address,
firmware version, user and system timer. To change or use these options, follow the
below instructions.
Firmware Version
A firmware update allows users to upgrade the IP camera’s firmware remotely.
Device Name
The device name can be found using the IP scan utility. This will identify the IP cameras. To
change the device name, enter the new name of the IP camera and click “Submit”.
OSD Font
Camera OSD name
OSD Timer
Camera OSD time
13
ActiveX OSD Name
Camera OSD name only on ActiveX
Chapter 4-3 Timer
The H.264 Full HD IP camera allows users to change the system timer via a standard
HTML web page. To change the camera’s system timer, enter the date and time into the
edit boxes. Click “Submit” to apply.
Synchronize with NTP
To synchronize the Internet time system, change the Auto Synchronize option to “Every
Hour”. The H.264 Full HD IP camera will synchronize its system timer with a time server
every hour.
Note: Network Time Protocol feature requires Internet connection.
Chapter 4-4 Video / audio settings
To transmit H.264 Full HD video over a low bandwidth network such as the Internet, set
the bitrate close to the networks upload bandwidth. H.264 Full HDIP cameras can
encode frames based on the bitrate setting.
14
Profiles: select streaming combination
Profile Name: description of the profile
Compression: compression type of the profile
Resolution: the resolution of the compression
VBR/CBR: VBR: video quality encoding mode/constant bitrate encoding mode.
Bitrate: the maximum bit rate available for a network connection
Output frame rate: the frame rate of the profile
GOP: 1 frame period per second
TV Output: NTSC/PAL video system
Power line frequency: 60Hz/50Hz lighting power frequency
Chapter 4-4-1 Weighted Mode
Weighted mode is activated when an alarm is triggered. When triggered the stream
rate increases to the maximum speed, i.e. 30 FPS. If there is no alarm activity, the
streaming remains low at 1 FPS saving bandwidth and storage.
15
Alarm Interval
Chapter 4-5 Basic Quality
To determine the video quality, adjust the brightness, contrast, hue, saturation, and
sharpness accordingly. The IP camera can be set to day and/or night for optimum video
quality.
Day or Night Video Mode
The day or night video quality can be adjusted separately; the quality setting is scheduled
based on the IR cut scheduling table.
Chapter 4-6 Network Settings
Network settings are the basic settings that connect H.264 Full HD IP cameras to the
network. The default IP address is 192.168.0.200. A user can use this IP address to verify
the network connection between a local PC and H.264 Full HD IP camera using the
Internet browser.
For a local area network configuration, enter the IP address, subnet mask, and gateway
IP. Click “Submit” to update the settings.
16
For Internet access configuration, contact your local Internet Service Provider (ISP) for a
global IP address. Once the Internet connection is installed, enter the IP address (global),
subnet mask, and gateway IP from the ISP.
Default DNS IP Address—First Domain Name Server, the IP address of
the domain name server
Second DNS IP Address—Second Domain Name Server, the IP address of
the domain name server, a backup DNS server for default DNS
PPPoE Account—Account name of PPPoE service
PPPoE Password—Password of PPPoE service
Chapter 4-6-1 DHCP Setting
A router, gateway, or other DHCP software server can remotely assign an IP address to
the H.264 Full HD IP camera. There is no need to configure the IP address, subnet mask,
and gateway. Since the DHCP may assign a different IP address to the IP camera after
power off, a user can use the IP scan utility to launch the Internet browser and search for
the IP camera. To enable DHCP, click the DHCP option and click “Submit”.
Note:Once the DHCP option is enabled, the IP camera is assigned an IP address by the
DHCP server. This feature is only permitted in LAN environments.
Chapter 4-7 HTTP & RTSP Service
HTTP protocol is a reliable protocol that sends video streams. Port forwarding
technology can be used to send video over the Internet. Details are described in the
appendix. To change the HTTP service’s port number, consult your network
administrator. Change the port number at the port field and click “Submit”.
17
Chapter 4-8 DDNS Settings
DNS stands for Domain Name Server. It provides a domain name translation service for a
device’s IP. The domain name can be easier to remember than numeric values (IP). The
DNS service requires service registration and subscription. DynDNS (DDNS) provides a
domain name service without subscription.
Note: The DDNS feature requires an Internet connection.
To use DDNS, go towww.ddnsipcam.com. If the IP camera is on Internet with a global IP
address, use the last 6 digits of the MAC address as the host name with default account
and the default password, (pass). The IP camera will automatically register to
www.ddnsipcam.com without further registering. For example, if the IP camera is on the
Internet, type “27fff0.ddnsipcam.com” into a browser with login name “27fff0” and
password “pass” to log in.
Chapter 4-9 UPnP Settings
The UPnP service is a network protocol that allows Windows PC users to explore IP
cameras within a LAN. In Windows, click on the Network of File Explorer to see the IP
cameras via the UPnP protocol.
18
To enable the UPnP service, visit Basic->Network->UPnP.
Chapter 4-10 Maintenance
The load default feature allows you to restore the factory settings. There are certain
settings such as IP addresses and video systems that are not affected by this operation. To
reboot the H.264 Full HD IP camera, click the Reboot System hyperlink.
To update the firmware for the IP camera, click the Firmware Update hyper link.
Locate “flasham32.bin” in your computer by clicking “Browse”. Click “Submit” to finish the
firmware upgrade.
19
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33

Acumen AiP-M34E-45Y0B User manual

Acumen
Brand
Acumen
Model
AiP-M34E-45Y0B
Category
Security cameras
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents