2. Awron
  3. E92DGA M3

Awron E92DGA M3 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Awron E92DGA M3 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Installation Instr. : E92DGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 23.02.2016
Seite: 1
AWRON Display E92DGA – M3
Installation Manual E90/E91/E92/E93
BMW
• E90 M3 - Limousine
• E92 M3 - Coupe
Installation Instr. : E92DGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 23.02.2016
Seite: 2
Table of Contents
Table of Contents 2
Scope of delivery 3
Toolkit 4
Cabel system 5
Schematic 6
Installation Guide
• Oppening interior trim 7
• Mounting AWRON display 8
• Cable installation on passenger footwall side 10
• Installation AWRON harness on the Junction-Box 14
• Diesel sensor connection (ONLY FOR DIESEL ENGINES) 19
• Installation and position of USB cable 22
Support & FAQs 23
Installation Instr. : E92DGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 23.02.2016
Seite: 3
Scope of delivery
Power cord set
E9xDGA Display module
Installation Instr. : E92DGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 23.02.2016
Seite: 4
Toolkit
Assembly tool
2mm
Mounting wedge
Screwdriver TORX
T20
Socket wrench
8mm
Flat screwdriver 2mm
Installation Instr. : E92DGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 23.02.2016
Seite: 5
Schematic
150cm
USB
Installation Instr. : E92DGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 23.02.2016
Seite: 6
Wiring diagram
Installation Instr. : E92DGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 23.02.2016
Seite: 7
Opening interior trim
Solve with a plastic wedge the interior trim. Start from the right. Look for the connector at the
start button and the control panel warning lights, etc. (see picture below right) Disconnect the
connectors, then they can remove the trim.
Use mounting wedge
Use mounting wedge Use mounting wedge
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 8
With a socket wrench 8mm remove the socket wrench, and also remove the two
marked nuts (see picture). Unclip the air ventilation duct from the interiors of the bar.
For this purpose, can be re-used the plastic mounting wedge.
Press the operating unit out of the front, now this is unplugged.
Mounting AWRON display
Socket wrench 8mm
No tools required
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 9
Clip the new ventilation duct with the AWRON display in your interior trim and
carefully remove the nuts.
The AWRON display can now be connected to the wiring harness and installed.
Now close the Start button and run the cable out of the control element between
the display and demister.
Then, the interior trim are installed in reverse order. Now connect the two plugs to
the control element and push it in from the front.
Mounting AWRON display
No tools required
Installation Instr. : E92DGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 22.02.2016
Seite: 10
Cable installation on passenger footwell side
1
2
3 4
5
6
For cable installation necessary flax as photos from 1-6 show.
Installation Instr. : E92DGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 22.02.2016
Seite: 11
Cable installation on passenger footwell side
Contact must be switched off or put the key in the ignition lock mandatory!
Screwdriver TORX T20
Remove the screws
marked in the picture of
the footwall cover. For
this operation use
Thorax T20
1
Power distribution
2
Junction box control unit
Blue
X14271
Black
X14272
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 12
1
Power distribution
2
Junction box control unit
Junction box installation point
Installation AWRON harness on the Junction-Box
Passenger side
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 13
Installation AWRON harness on the Junction-Box
Pin X14271 54-blue pinpolig Cable color
1 PT-CAN_HIGH BLUE/RED 0.35mm²
2 PT-CAN_LOW RED 0.35mm²
Pin X14272 54-black pin Cable color
1 Kl. 30G RED/YELLOW 0.35mm²
6 MASS BROWN 0.35mm²
ATTENTION:
The Blue connectors can be located on either the left or right
side of the junction box depending on the year.
Important! The blue plug is always the CAN, and the power
supply to the black.
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 14
No tools required
Installation AWRON harness on the Junction-Box
Contact must be switched off or put the key in the ignition lock mandatory!
No tools required
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 15
Insert two pins of the vehicle wiring harness into white connector housing. Orientate and pay attention on
the color of the AWRON wire and unplag pin 1 and pin 2 from AWRON harness into blue connector on
the position like picture showed.
Cable installation on passenger footwell side
Contact must be switched off or put the key in the ignition lock mandatory!
Connect white connector from vehicle harness to the white connector from AWRON harness
1
2
CONNECT
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 16
No tools required
Cable installation on passenger footwell side
Contact must be switched off or put the key in the ignition lock mandatory!
No tools required
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 17
Insert two pins of the vehicle wiring harness into black connector housing. Orientate and pay attention on
the color of the AWRON wire and unplug pin 1 (red/yellow) and pin 6 (brown) from AWRON harness into
black connector X14272 on the position like picture showing.
Cable installation on passenger footwell side
Contact must be switched off or put the key in the ignition lock mandatory!
Finall connection on booth connector
6
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 18
Return booth (black and blue connector) to the Junction box
Cable installation on passenger footwell side
Contact must be switched off or put the key in the ignition lock mandatory!
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 19
Installation and position of USB cable
At final step you need to install USB cable between passenger seat and hand brake.
Installation Instr. : E9xDGA
Autor:
AWRON GmbH
Version: V1.1
Datum: 28.04.2015
Seite: 20
Support & FAQ
For all enquiri es concerning your
AWRON display system, or if you
have problems with installation
guide the AWRON support team
at support@awron.de are at your
service.
Please also seen us and our
another AWRON products on
our website www.awron.de
/