Pella Rolscreen 3525, 3550, 3570 Handle Set Instructions

Brand: Pella

Model: Rolscreen 3525, 3550, 3570

Type: Handle Set Instructions

Installation Instruction

Rev. 01/10/05

Surface Mount Hardware

Page 1 of 2

IMPORTANT! Read thoroughly before beginning. Failure to install as recommended will void any warranty, express or implied.

Part Number: 31356

Entry

Door

Deadbolt

Clearance

Interior Latch

Tools Required:

• Centerpunch

• Drill

• 3/32" Drill bit

• 5/16" Drill bit

• 7/8" Spade bit (provided)

• Phillips screwdriver

• Scissors

• 3/32" Hex key (provided)

• 1/8" Hex key (provided)

NOTE: The handle style shown in the illustrations may be different than the style of handle being installed. The steps for installing the handles will be

the same for all handle styles.

Supplies Needed:

• Handle Kit Package

1 TEMPLATE FOLDING AND POSITIONING

Continued on page two

A. Cut out the template located at the bottom of this page and fold on the two

lines as indicated.

B. Position the template on the latch side of the door. Align the upper large 7/8"

diameter hole, 39-1/2" up from the bottom of the door.

C. Make certain the template holes are aligned vertically and tape in place.

39½"

Template

Tape

2 INTERIOR LEVER POSITIONING

A. Hold the interior latch and deadbolt onto the template to test the clearance

with your entryway door handle. Move the template up or down enough to

eliminate any interference.

B. Centerpunch, remove the template and drill holes halfway through the door

from each side using the drill bits indicated.

FOLD ALONG THIS LINE - DO NOT CUT

39-1/2”

CHECK FOR

CLEARANCE WITH

PRIME DOOR LATCH

CENTERPUNC

H & DRILL ALL

HOLES

HALFWAY

THROUGH THE

DOOR

CHECK FOR

CLEARANCE WITH

PRIME DOOR LATCH

FOLD ALONG THIS LINE - DO NOT CUT

CENTERPUNCH

& DRILL ALL

HOLES

HALFWAY

THROUGH THE

DOOR

5/16”

7/8”

Spade

Bit

7/8”

Spade

Bit

7/8”

Spade

Bit

7/8”

Spade

Bit

1-5/16”

Strike

Screw

Bolt

Shims

If needed)

Deadbolt Strike

A. Close the door and position the angled latch strike behind the latch bolt.

B. Mark and drill the centers of the slotted holes using a 3/32" drill bit.

C. Install the two #6 x 1-1/4" strike screws. Adjust the strike for proper operation.

NOTE: Shims are included if it is necessary to build out the strike.

5 INSTALLING THE LATCH STRIKE

6 INSTALLING THE DEADBOLT STRIKE

A. Position the deadbolt strike behind the deadbolt.

B. Mark and drill the centers of the slotted holes using a 3/32" drill bit.

C. Install the two #6 x 1-1/4" strike screws. Adjust the strike for proper operation.

NOTE: Shims are included if it is necessary to build out the strike.

Latch Strike

Shims

(If needed)

Latch

Bolt

Strike Screw

A. Insert a key in the key cylinder, slide the cylinder into the exterior handle and

rotate 180 degrees (halfway), then remove the key, securing the cylinder in

place.

B. Insert the flat spindle into the back side of the key cylinder.

C. Set the exterior lever in place and rotate the lever to the proper position.

D. Insert the square spindle into the back of the interior latch.

E. From the inside, install the interior latch and secure using two #6-32 x 1-7/8"

latch screws.

F. Hold the exterior lever and interior latch together and tighten the set screw

on both levers with the hex keys provided. (1/8" for exterior and 3/32" for

interior.)

3 INSTALLING THE INTERIOR LATCH AND EXTERIOR LEVER

4 INSTALLING THE DEADBOLT

A. Position the deadbolt onto the flat spindle and secure using two #6-32 x 1-7/8"

deadbolt screws.

Exterior

Lever

Interior Latch

Latch Screw

Set Screw

Key Cylinder

Square

Spindle

Set Screw

Flat Spindle

Exterior

Lever

Deadbolt

Screw

Deadbolt

Interior Latch

Flat

Spindle

Pella Rolscreen 3525, 3550, 3570 Handle Set Instructions

Pella Rolscreen 3525, 3550, 3570 Handle Set Instructions

Pella Rolscreen 3525, 3550, 3570 Handle Set Instructions

Related papers

Other documents