Grizzly C1651 Owner's manual

-1-

INSTRUCTIONS FOR

C1393-96, C1651

STILE AND RAIL SETS

• Failure to follow these guidelines will result in

seriouspersonalinjury.

• ALWAYSWEARANSIAPPROVEDEYEANDEAR

PROTECTIONwhenusingthisbit.

• Alwaysusearoutertablewhenusingthesebits,

NEVERattempttouseahand-heldrouter.

• Neverfeedlumberwiththerotationofthecutter.

• Follow the safety guidelines set forth by the

manufactureroftherouterandroutertable.

These router bits have sharp edges. Use care

whileremovingthewaxyprotectivecoating.Never

turnontherouterwiththeprotectivecoatingstill

onthebit.

• Unplug router before installing or adjusting

cutter.

• Keep all guards and anti-kickback devices in

place.

• Double check bit to insure it is tight and

secureinrouter.

• Alwaysinspectlumberandotherwoodmaterials

for cracks, knots, or other imperfections that

couldcauselumbertokickorshatterwhilemill-

ing.

Togetthemostfromthesecarbide-tippedstile

andrailbits:

1. For maximum efficiency, secure each bit in a

routerandplanallofyourcutstominimizebit

changes(or keep eachbitin aseparaterout-

er).

2. Adjusttherouterand

bit in your router

table, so the

bit offers a

fullprofilein

addition to

about

⁄8"of

indentation

on the front

edge of the

material. You will be milling your

material back side up, so the indentation

willbeattablelevel.(Seetheillustrationtothe

right.)

3. Oncethebitisproperlyadjustedandtightened

inplace,usealengthofsurplusmaterialthatis

the same thickness as your workpiece  for a

test cut. If you are satisfied with your results,

continuewithyourprojectmaterial.engagement

toensureanequaldepthofcut.

FENCE

StileandRailSet

Deluxecarbide-tippedStileandRailbitsinanum-

berofclassicandcontemporarystyles,offerexcel-

lent  performance for the serious woodworker or

cabinetmaker working with stile and rail materials,

rangingfrom

⁄4"to

⁄8"widths.Two-piecerouterbit

setsenableyoutoincreaseproductivitybykeeping

tworouterspre-adjusted.

INTRODUCTION

Although these bits can be used hand-held with

properjigsandfixtures,werecommendusingthem

inaroutertable,suchastheRebel

RouterTableby

WoodstockInternational.

-2-

The process for completing your rail end cuts is

roughly the same as those for your stile and rail

cuts.Themainconcernisensuringthattheamount

ofrevealatthefrontedgeofyourrailmatchesthe

cutsmadeinyourstiles.

Tocompleteyourendrailcuts:

1. Adjustyourrouterand

bit,asdescribed

earlier,

and

make

atest

cut

with

thesur-

plusmate-

rial.

2. Join the test cut with your  previous cuts and

checkthejointtodetermineflushness.

3. Re-adjustandre-testuntilyouaresatisfiedwith

yourresults.

4. Whensatisfiedwiththeresultstightentherouter

andcutyourprojectmaterial.

A ball bearing is supplied with these router bits

whichallowtheuseoftemplatesforcurvedwork

asseentotheright.

Usingatemplate:

1. Thetem-

plate

should

bethe

same

sizeas

the

expected

finished

panel.

2. The curved portion of the workpiece should

be rough cut so that no more than

⁄8" pro-

trudesbeyondthetemplate.

3. Thefenceandmitermustberemovedwhen

usingatemplate.Astartingpinorblockmust

beinstalledasshowninFigure2.

Always disconnect power to

themachinewhensettingup

or making adjustments.

Failure to do this may result

inseriouspersonalinjury.

FENCE

Figure2.Startblockfortemplatecutting.

Grizzly C1651 Owner's manual

Related papers

Other documents