none 9705F3BXS Installation guide

none
Brand
none
Model
9705F3BXS
Type
Installation guide

The none 9705F3BXS is a versatile fountain system that can be used to create a beautiful and relaxing water feature in your home or garden. It is easy to set up and maintain, and it comes with a variety of features that allow you to customize the look and feel of your fountain.

The 9705F3BXS includes a 6027H basin, a 4027A fountain top, a pump, a light, and a restrictor. The basin is made of durable concrete and is available in a variety of colors and finishes. The fountain top is made of lightweight plastic and features a built-in light ring. The pump is powerful enough to create a steady stream of water, and the restrictor allows you to adjust the flow rate.

The none 9705F3BXS is a versatile fountain system that can be used to create a beautiful and relaxing water feature in your home or garden. It is easy to set up and maintain, and it comes with a variety of features that allow you to customize the look and feel of your fountain.

The 9705F3BXS includes a 6027H basin, a 4027A fountain top, a pump, a light, and a restrictor. The basin is made of durable concrete and is available in a variety of colors and finishes. The fountain top is made of lightweight plastic and features a built-in light ring. The pump is powerful enough to create a steady stream of water, and the restrictor allows you to adjust the flow rate.

SETTING UP A 9705F3 FOUNTAIN
1) Set your 6027H Basin on your chosen area after ensuring the
location is firm and level. Rotate the Basin until the small opening
at the bottom edge is closest to your electrical supply.
2) Preassemble components of the 4027A fountain top. Attach the
tube to the barb under the AB870 Light. Then from the top, pass the
tube and the light power cord together down through the opening in
the top of the 4027A. Allow the light ring to sit snug in the recess
on top of the concrete piece.
3) Slip the Restrictor onto the tube, tightening it just enough to stay
in place just below the 4027A. Set the 4027A down for the moment.
4) Thread the barbed adapter into the pump. Push the pump with
its adapter into the other end of the tube.
5) Install the rubber stopper around the pump cord (use the larger
hole) about 10” below the pump. Place the cord (smaller hole) in
the stopper where the cord is about three feet from the light.
6) Rest the 4027A on the 6027H (with some padding, like a burlap
bag in between). The pump should settle in the lower, center part
of the basin and the two power cords should be slipped down
through the hole in the center of the basin. Reach under the basin
piece and pull the cords out the small opening at the bottom.
7) Reaching back into the lower, center part of the basin, push the stopper into the center hole until it is tight, leaving about 1/8” showing
above the hole.
8) Remove the padding and set the 4027A on the 6027H. Fill the basin with water, read your pump and light instructions, and plug
both units into a GFCI outlet. Attach the cattail / frog feature as shown and enjoy your new fountain.
csd – 8/8/11
IMPORTANT – WINTER CARE
Winter ice build-up can cause damage to concrete statuary. Follow these tips to reduce winter weathering to your fountain:
* Disconnect power to pumps and lights.
* Remove plugs / stopper in all fountain bowls to open drains and let all moisture out. Keep drains open throughout winter.
* Place an absorbant material like burlap, blankets, etc. inside vases/bowls and cover all with a Henri fountain cover.
* Do not allow snow or ice to build up on or against the concrete. Remove snow before it turns to ice. Do not use salt or chemical ice removers, as these
may damage concrete.
  • Page 1 1

none 9705F3BXS Installation guide

none
Brand
none
Model
9705F3BXS
Type
Installation guide

The none 9705F3BXS is a versatile fountain system that can be used to create a beautiful and relaxing water feature in your home or garden. It is easy to set up and maintain, and it comes with a variety of features that allow you to customize the look and feel of your fountain.

The 9705F3BXS includes a 6027H basin, a 4027A fountain top, a pump, a light, and a restrictor. The basin is made of durable concrete and is available in a variety of colors and finishes. The fountain top is made of lightweight plastic and features a built-in light ring. The pump is powerful enough to create a steady stream of water, and the restrictor allows you to adjust the flow rate.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents