Rugged Ridge 11214.50 Installation guide

Category
Car kits
Type
Installation guide

Rugged Ridge 11214.50 is a dual battery tray designed for 1970-1986 CJ5, CJ7, and CJ8, as well as 1987-1990 YJ Wranglers. This tray allows for the installation of a second battery, providing additional power for accessories or backup in case of a main battery failure. The tray is made of durable materials and is designed to fit securely in the vehicle without drilling. It comes with all necessary hardware for installation, including a firewall support bracket, inner fender brace, and battery retainer bar. With the Rugged Ridge 11214.

Rugged Ridge 11214.50 is a dual battery tray designed for 1970-1986 CJ5, CJ7, and CJ8, as well as 1987-1990 YJ Wranglers. This tray allows for the installation of a second battery, providing additional power for accessories or backup in case of a main battery failure. The tray is made of durable materials and is designed to fit securely in the vehicle without drilling. It comes with all necessary hardware for installation, including a firewall support bracket, inner fender brace, and battery retainer bar. With the Rugged Ridge 11214.

Contents:
(1) Dual Battery Tray
(1) Firewall Support Bracket
(1) Inner Fender Brace (YJ)
(1) Diagnostic Plug Bracket
(YJ optional)
(1) Fender shield
(2) Phillips Head Screws 
Page 1 of 2
11214.50 Dual Battery Tray
Applications: 1970 - 86 CJ5, CJ7, and CJ8
1987 -90 YJ Wrangler
Dual Battery Tray Installation Instructions CJ/YJ 1970-1990 (No Drill Application)
Step 1: For CJ applications remove Jack
and tire tool. These items will need
to be relocated. If desired the handle
can be shortened by 4" and secured
back in the original location.
Step 2: Disconnect Battery by removing the
NEG (-) cable first and then the POS
(+) connector. Remove battery from
tray.
Step 3: For YJ applications remove relays
by releasing holding tabs. This can be
done using pliers. If the vehicle is
equipped with diagnostic plugs
disconnect at this time.
Step 4: Unbolt old tray and remove. Retain
all mounting bolts and any clips.
They will be reused.
For CJ applications remove lower
tray braces.
Step 5: For YJ applications (if equipped)
remove and relocate emission
vent sensor and vacuum 4WD
indicator assembly. Relocate to
stud located above and to the
right on firewall.
Step 6: For YJ applications install fender
brace to three studs on bottom of
Dual Battery Tray. Use 10mm hex
nuts (do not tighten).
Step 7: Install Fire Wall Support Bracket to
Dual Battery Tray with 14mm Hex
Nut (do not tighten). Install lower
fender shield using two 10mm Hex
Head Nuts. Plate attaches to the
bottom of Dual Battery Trays front
right corner. Secure nuts.
Step 8: Install Dual Battery Tray to vehicle.
Reuse mounting bolts removed in
step 4. Adjust tray as needed and
tighten all bolts and hex nuts at this
time.
Step 9: For YJ application install supplied
Diagnostic Plug Bracket if needed.
Harness should be pulled to the
right side of tray. Feed plug through
opening in bracket and attach with
supplied screws.
If equipped, snap relays into Diagnostic
Plug Bracket.
Step (2) Step (4)
Step (6) Step (8)
(3) Threaded "J" Hooks
(3) Nylon Flat Washers
(3) Wing Nuts
(1) Battery Retainer Bar
(7) Bracket 10mm Hex Nuts
(1) 14mm Support Bracket Hex Nut
Page 2 of 2
11214.50 Dual Battery Tray
Applications: 1970 - 86 CJ5, CJ7, and CJ8
1987 -90 YJ Wrangler
Dual Battery Tray Installation Instructions CJ/YJ 1970-1990 (No Drill Application) Page 2
Step 10: Place one "J" hook into the
center hole of the Dual Battery
Tray.
Step 11: Insert the other two "J" hooks into
the left and right holes of the Dual
Battery Tray. The hooks should be
facing outwards, away from the Tray.
Step 12: Place batteries onto Tray. Place
Battery Retainer Bar over batteries
and align holes with "J" Hook. Place
Nylon Flat Washer and Wing Nut
onto "J" Hooks and tighten Wing
Nuts evenly. Place Red protective
caps onto the ends of the "J" Hooks.
"J" Hooks can be trimmed if needed.
Some batteries may need to have
plastic lower lips notched to allow
proper fitment.
Step 12: Install battery cables starting with
POS (+) cables first. Refer to
instructions supplied with Dual Battery
Relay for further wiring for dual
battery setups. See drawing for
possible layout.
Omix-Ada Inc.
460 Horizon Dr. Suite 400
Suwanee, Georgia 30024
Relay Relay
Diagnostic
CJ/YJ
Stock (+) Cable to Starter
Stock (-) cable to Body
Frame Ground
Main Battery Auxillary Battery
Trim Battery here
if needed
  • Page 1 1
  • Page 2 2

Rugged Ridge 11214.50 Installation guide

Category
Car kits
Type
Installation guide

Rugged Ridge 11214.50 is a dual battery tray designed for 1970-1986 CJ5, CJ7, and CJ8, as well as 1987-1990 YJ Wranglers. This tray allows for the installation of a second battery, providing additional power for accessories or backup in case of a main battery failure. The tray is made of durable materials and is designed to fit securely in the vehicle without drilling. It comes with all necessary hardware for installation, including a firewall support bracket, inner fender brace, and battery retainer bar. With the Rugged Ridge 11214.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI