Canopia by Palram 702517 Operating instructions

Category
Car kits
Type
Operating instructions
eStssembly Instructions
Snap&Grow
- Anchoring Kit
.0
sM
After Sale
Service
USA 877-627-8476 1 England 01302-380775
1
France 0169-791-094
Canada 1 800-866-5749 Germany 0180-522-8778 International +972 4-848-6942
www.palramapplications.com
Before you start
IRIt
is highly
recommended to be assisted by a second person in some steps.
IRSort
the parts and check
according to the contents parts list.
IRThe
product must be
positioned and fixed on a leveled surface.
IRMake
sure that screws
and anchors suit the surface type.
IRThis
product is suitable
for all Snap&Grow greenhouses up to 8 feet long.
Please be safe during
assembly.
You will
need
To assembly this product
(these items not supplied)
411
Safety
This product should be
mounted to the ground as shown in these instructions
LJ
in order to ensure
greenhouse's stability and appropriate wind resistance.
Some parts may have
sharp edges. Please be careful when handling
components.
Always wear gloves, eye
protection, and long sleeves when assembling or
performing any
maintenance on your product.
If using a stepladder or
power tools please ensure that you follow the
manufacturer's safety
advice.
IRDO
not lean the
stepladder against the greenhouse.
IRDo
not stand on the
greenhouse roof/panels
IRTo
prevent injuries, do
not allow children to play under the greenhouse
during assembly.
Please read these instructions
carefully before you start to
assemble this product.
Please carry out the steps in the
order set out in these instructions.
Keep these instructions in a safe
place for future reference.
Care and Maintenance
0
Periodically check the product to
assure that it remains stable.
0
Keep roof clean of snow.
During
Assembly
During assembly you will
encounter the information icon, please
refer to the relevant assembly step
for additional comments and
assistance.
Do not cut the steel cable unless a final
decision on the mounting location
has been made.
Step 3 : According to the ground surface
type, follow the appropriate
mounting procedure.
Option 1 : for hard surfaces (concrete or
wood)
Option 2 : soft/ground installation.
Step 5 : After the product has been
installed, fasten the steel cable by
turning part #7332
Tighten all screws when completing
assembly.
Contents
Item
Qty.
4010
4000
7409
7410
7333
7332
7331
4
(+1)
4
(+1)
Item
Qty.
414
433
7283
7327
7336
2
(+1)
6
(+1)
2
(+1)
2
4
1
7327
2
®+
®
7410
2
11.11111111111
2
7409 4
3
7331 4
4000
11)MMONNOWNW
4
4010
4
433
4 7336
4
- -
45-55 cm
1'513/462
Ay_
14-
1
N
4114414
i
4
4 '
41
4
4
,
,41 ,
4
411
4
4,14
'44
,
14
40
4,44,
,446_1
4
4,4
4,44
111111111Mil
44414 441
.
44
141
41
i
4
0
11KIV
4414
41141
4411::',,
141
6-
i
'
4'
\ WO%
411,4
1'1
14
1
1
4 .,
11
4
1
1
, 4,
\ VMS
40 ',4,
4414
,
O
4 1 41
4
4'
44'1441411
\
0
All
111
1
41'1141'14
1
41
4
4
11
11'
41
4
4
14
4
4'11
4
1
.7r
Co
N
N
N
Master_SNG_Anchoring_Kit_V1
-4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Canopia by Palram 702517 Operating instructions

Category
Car kits
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI