Palram 702517 Operating instructions

eStssembly Instructions

Snap&Grow

- Anchoring Kit

.0

sM

After Sale

Service

Email: [email protected]

USA 877-627-8476 1 England 01302-380775

1

France 0169-791-094

Canada 1 800-866-5749 Germany 0180-522-8778 International +972 4-848-6942

www.palramapplications.com

Before you start

IRIt

is highly

recommended to be assisted by a second person in some steps.

IRSort

the parts and check

according to the contents parts list.

IRThe

product must be

positioned and fixed on a leveled surface.

IRMake

sure that screws

and anchors suit the surface type.

IRThis

product is suitable

for all Snap&Grow greenhouses up to 8 feet long.

Please be safe during

assembly.

You will

need

To assembly this product

(these items not supplied)

411

Safety

This product should be

mounted to the ground as shown in these instructions

LJ

in order to ensure

greenhouse's stability and appropriate wind resistance.

Some parts may have

sharp edges. Please be careful when handling

components.

Always wear gloves, eye

protection, and long sleeves when assembling or

performing any

maintenance on your product.

If using a stepladder or

power tools please ensure that you follow the

manufacturer's safety

advice.

IRDO

not lean the

stepladder against the greenhouse.

IRDo

not stand on the

greenhouse roof/panels

IRTo

prevent injuries, do

not allow children to play under the greenhouse

during assembly.

Please read these instructions

carefully before you start to

assemble this product.

Please carry out the steps in the

order set out in these instructions.

Keep these instructions in a safe

place for future reference.

Care and Maintenance

0

Periodically check the product to

assure that it remains stable.

0

Keep roof clean of snow.

During

Assembly

During assembly you will

encounter the information icon, please

refer to the relevant assembly step

for additional comments and

assistance.

Do not cut the steel cable unless a final

decision on the mounting location

has been made.

Step 3 : According to the ground surface

type, follow the appropriate

mounting procedure.

Option 1 : for hard surfaces (concrete or

wood)

Option 2 : soft/ground installation.

Step 5 : After the product has been

installed, fasten the steel cable by

turning part #7332

Tighten all screws when completing

assembly.

Contents

Item

Qty.

4010

4000

7409

7410

7333

7332

7331

4

(+1)

4

(+1)

Item

Qty.

414

433

7283

7327

7336

2

(+1)

6

(+1)

2

(+1)

2

4

1

7327

2

®+

®

7410

2

11.11111111111

2

7409 4

3

7331 4

4000

11)MMONNOWNW

4

4010

4

433

4 7336

4

- -

45-55 cm

1'513/462

Ay_

14-

1

N

4114414

i

4

4 '

41

4

,

,41 ,

4

411

4

4,14

'44

,

14

40

4,44,

,446_1

4

4,4

4,44

111111111Mil

44414 441

.

44

141

41

i

4

0

11KIV

4414

41141

4411::',,

141

6-

i

'

4'

\ WO%

411,4

1'1

14

1

4 .,

11

4

1

, 4,

\ VMS

40 ',4,

4414

,

O

4 1 41

4

4'

44'1441411

\

0

All

111

1

41'1141'14

1

41

4

11

11'

41

4

14

4

4'11

4

1

.7r

Co

N

Master_SNG_Anchoring_Kit_V1

-4

Palram 702517 Operating instructions

Palram 702517 Operating instructions

Related papers

Other documents