natural NATSG100 Installation guide

Type
Installation guide

This manual is also suitable for

Natural NATSG100 is an underlayment designed to enhance the performance of laminate, hardwood, and engineered flooring. It offers excellent acoustical properties, reducing noise and improving soundproofing. With a thickness of 2 mm, it provides a smooth and even base for flooring installation. Its water vapor transmission rate of 0.31 lbs/24hrs/1000sq.ft helps protect against moisture damage, making it suitable for use in basements or areas requiring a moisture barrier. Easy to install, Natural NATSG100 comes with an attached tape for sealing seams and ensuring a secure, vapor-tight seal.

Natural NATSG100 is an underlayment designed to enhance the performance of laminate, hardwood, and engineered flooring. It offers excellent acoustical properties, reducing noise and improving soundproofing. With a thickness of 2 mm, it provides a smooth and even base for flooring installation. Its water vapor transmission rate of 0.31 lbs/24hrs/1000sq.ft helps protect against moisture damage, making it suitable for use in basements or areas requiring a moisture barrier. Easy to install, Natural NATSG100 comes with an attached tape for sealing seams and ensuring a secure, vapor-tight seal.

FOR LAMINATES, HARDWOOD AND ENGINEERED
Installation instructions
1. Check for nails.
2. Sweep or mop.
3. Roll out 1 width of membrane.
4. Cut roll at wall.
5. Install flooring planks.
6. Roll out next width.
7. Seal seams using the attached tape by removing paper strip and pressing the tape down to
adhere to membrane.
Repeat steps 3 to 7 until floor is completed.
NOTE: When installing Natural SG in basement or where a moisture barrier is required, extend the underlayment 1” - 2” up the
sides of all walls. To ensure the vapor barrier qualities of Natural SG are maintained, a vapor tape is required to seal all seams
that are not sealed by the Seal Guard system. New concrete should cure for 60-90 days minimum, before installing flooring
products. Check for excessive moisture in various areas before installation referring to flooring manufacturer’s recommendations.
Consult with your flooring specialist for additional instructions.
Technical Data
Properties
Method
Performance
Acoustical
ASTM E 2179-03
Delta 21
ASTM E 492-4 / 989-89
IIC 73
ASTM E 90-04 / 413-04
STC 72
Thickness
ASTM-D3575
2 mm
Water Vapor
Transmission Rate
ASTM E 96
0.31 lbs/24hrs/1000sq.ft
Impact Resistance
ISO/DIS 24335
NALFA LF01 -2003
Large Ball Test
1100 mm
Commercial
Compression Resistance
ASTM D3575Suffix D
8 lbs/in2
Compression Set
ASTM D3575Suffix B
30%
Compressive Creep
EN 1606 / EN 13163
10% (12 kPa)
Tensile Strength
ASTM-D-3575
95 lbs/in2
Thermal Resistance
ASTM-C-518
3.8
Maximum Temperature
95ºC (203ºF)
IMPORTANT NOTICE:
The above specifications were collected in a controlled environment. This information relates only to
Natural SG and does not take into consideration the floor system and environment into which it will be
used. Individual floor systems may affect the performance of Natural SG. Proper sub-floor preparations
and following the finished floor manufacturer’s instructions is crucial to a successful installation.
Further information and about these tests are available.
  • Page 1 1
  • Page 2 2

natural NATSG100 Installation guide

Type
Installation guide
This manual is also suitable for

Natural NATSG100 is an underlayment designed to enhance the performance of laminate, hardwood, and engineered flooring. It offers excellent acoustical properties, reducing noise and improving soundproofing. With a thickness of 2 mm, it provides a smooth and even base for flooring installation. Its water vapor transmission rate of 0.31 lbs/24hrs/1000sq.ft helps protect against moisture damage, making it suitable for use in basements or areas requiring a moisture barrier. Easy to install, Natural NATSG100 comes with an attached tape for sealing seams and ensuring a secure, vapor-tight seal.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI