2. ENFORCER
  3. SL-3301-BAQ
SL-3301-BAQ

ENFORCER SL-3301-BAQ Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the ENFORCER SL-3301-BAQ Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the operating voltage range of the SL-3301-BAQ?
    How many trigger input wires does the SL-3301-BAQ have?
    What is the maximum current draw of the SL-3301-BAQ?
    What is the adjustable strobe speed range of the SL-3301-BAQ?
    What is the operating life of the SL-3301-BAQ?
    What is the IP rating of the SL-3301-BAQ?
    How many colors can the SL-3301-BAQ display?
    How can the color and strobe settings be configured on the SL-3301-BAQ?
    What is the default DIP switch setting on the SL-3301-BAQ?
SL-3301-BAQ
Multi-Color LED Strobe Light
Manual
•
Utilizes high-intensity LEDs
• 5 Vertical LED strips (25 LEDs total)
increase visibility from various directions
• Adjustable strobe speed, 60~260 times/min
• High-impact resistant case
• High-impact and heat-resistant lens
• Reverse polarity protection
• Weather resistant – IP66
Features
:
• 7 Colors possible – Red, green, blue,
cyan, magenta, yellow, and white
• Operating life of over 50,000 hours
(over 5.7 years)
• Simple 2- to 5-wire installation
• Set color via DIP switches, or trigger
colors with an external device via 3
trigger input wires
ENFORCER Multi-Color LED Strobe Light
2 SECO-LARM U.S.A., Inc.
The
ENFORCER
Multi
-
LED Strobe Light
provide
s
all the functions of a re
gular strobe light, but with
more versatility. The Multi-Color LED Strobe Light can change between seven different colors which can be
set manually via DIP switches, or triggered by an external device via 3 trigger input wires. There are 5 vertical
LED strips, making the light more visible from various directions, and a variable resistor to adjust flashing
speed. The Multi-Color LED Strobe Light has an operating life of 50,000 hours — over 160 times that of a
regular strobe light. No more bulbs to replace!
Overview:
Parts List:
1x
LED Strobe Light
1x
Manual
2x
Mounting Screw
with “O” ring
Specifications
:
Vertical LED strips
5
Total number of LEDs
25
Possible colors
Red, green, blue, cyan, magenta,
yellow, white
Operating voltage
9~
24
VAC/VDC
Current draw @12VDC (max.)
Strobe
3
50mA
Steady ON
3
50mA
Adjustable strobe speed
Maximum setting
26
0
times/min
Minimum setting
6
0 times/min
Operating life
Over 50,000 hours (over 5.7 years)
Operating
temperature
-
4°~144
° F
(
-
20°~65
° C)
Electrical protection
Reverse polarity protected
IP rating
IP66
Base
High
-
impact
resistant
black ABS
Lens
High
-
impact
heat
-
resistant acrylic
Dimensions
3
15
/
16
"
x3
1
/
8
"
(100x79
mm)
Circuit board
Rubber “O” ring
Power wire (brown)
Ground wire
(black)
DIP Switches
(for Power ON mode)
Circuit board
LEDs
LED
Strobe or
steady ON jumper
(default, strobe)
Remove thinned
-
out slot for
surface wiring
Circuit board screw
Trigger wires
Vertical LED strips
SECO-LARM
®
SL
-
3301
-
BAQ
Strobe
Steady ON
+
+
-
170–226
B1
B2
G1
G2
R1
R2
Blue
Green
Red
Mounting screw with
rubber “O” ring
Green trigger wire
Red trigger wire
Blue trigger wire
Strobe speed control
Strobe Steady ON
Introduction
:
ENFORCER Multi-Color LED Strobe Light
SECO-LARM U.S.A., Inc. 3
Configuring
LED Color and Strobe
:
1.
Decide where the LED strobe light is to be mounted.
Use a pencil to mark the location of the two mounting
screws.
2. Drill a hole through the wall or surface where the LED
strobe light is to be mounted. Run the ground (black)
and power (brown) wires through the wall.
NOTE: For surface wiring applications, remove the
thinned-out slot with a pair of pliers.
3. Connect the wires to their respective locations on an
alarm control panel or other security panel.
4.
Remove the lens and mount the LED strobe light to
the surface using the two included mounting screws
with rubber “O” rings. If screws are fastened too
tightly, the “O” rings will be damaged.
5. Select the color and strobe setting using the DIP
Switches (see chart below for details) and adjust
the speed using the strobe speed control
(clockwise
to increase, counterclockwise to decrease).
6. Replace lens. If lens is fastened too tightly, the
“O” ring will be damaged.
Installation
:
IMPORTANT: Disconnect power before adjusting DIP switches.
B1
B2
G
1
G2
R
1
R2
Trigger Mode
•
Before starting, please read this manual carefully and keep it for future reference.
• Be sure to use the LED strobe light within the given electrical limits.
Power ON Mode
1.
Decide where the LED strobe light is to be mounted.
Use a pencil to mark the location of the two mounting
screws.
2. Drill a hole through the wall or surface where the LED
strobe light is to be mounted. Run the ground (black)
and trigger (blue, green, red) wires through the wall.
NOTE: For surface wiring applications, remove the
thinned-out slot with a pair of pliers.
3. Connect the wires to their respective locations on an
alarm control panel, other security panel, or trigger
device according to the color desired (see chart below).
4.
Remove the lens and mount the LED strobe light to
the surface using the two included mounting screws
with rubber “O” rings. If screws are fastened too
tightly, the “O” rings will be damaged.
5. Set the LEDs to "strobe" or "steady ON" via the
jumper, and adjust the strobe speed using the
strobe speed control (clockwise to increase,
counterclockwise to decrease).
6. Replace lens. If lens is fastened too tightly, the
“O” ring will be damaged.
Default DIP Switch Setting: Red strobe
Color Strobe Setting
LED
Jumper
DIP Switch
Configuration
Trigger Wire
Connections
Red
LEDs strobe continuously
Strobe R2 ON only (default)
Connect red wire to GND
LEDs are steady ON Steady ON R1 ON only
Green
LEDs strobe continuously
Strobe G2 ON only
Connect green wire to GND
LEDs are steady ON Steady ON G1 ON only
Blue
LEDs strobe continuously
Strobe B2 ON only
Connect blue wire to GND
LEDs are steady ON Steady ON B1 ON only
Cyan
LEDs strobe continuously
Strobe G2 and B2 ON
Connect green and blue
wires to GND
LEDs are steady ON Steady ON G2 and B2 ON
Magenta
LEDs strobe continuously
Strobe R2 and B2 ON
Connect red and blue wires
to GND
LEDs are steady ON Steady ON R2 and B2 ON
Yellow
LEDs strobe continuously
Strobe R2 and G2 ON
Connect red and green
wires to GND
LEDs are steady ON Steady ON R2 and G2 ON
White
LEDs strobe continuously
Strobe R2, G2, and B2 ON
Connect all three trigger
wires to GND
LEDs are steady ON Steady ON All ON
NOTE:
For Trigger Mode,
LED
strobe and steady on setting is set
with jumper, see Overview (pg. 2).
ENFORCER Multi-Color LED Strobe Light
4 SECO-LARM U.S.A., Inc.
Dimensions:
NOTICE
:
The SECO
-
LARM policy is one of continual development and improvement. For that reason, SECO
-
LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2019 SECO-LARM U.S.A., Inc. All
rights reserved.
SECO
-
LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
PITSW1
Order Part#: 762-514%
MI_SL-3301-BAQ_190619.docx
Replacement
White Diffuser Lens
Conduit Drop Conduit Box
LED
Strobe Lights
SL
-
126
L
Q/WD
SL
-
1901
-
DAQ
SL
-
1901
-
JAQ
SL
-
1301
-
SAQ Series
Conduit Application Photos
Conduit Drop
Conduit Box
Both
Also Available from
SECO
-
LAR
M
®
:
The LED strobe light does not turn on
•
Check the LED strobe light’s power source
The LED strobe light does not flash correctly
•
Disconnect power, reconfigure LED color and strobe
settings, and reconnect power
WARRANTY:
This SECO
-
LARM product is warranted against defects in
material and workmanship while used in normal
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
Troubleshooting
:
Top View
Front View
Bottom View
3
15
/
16
"
(100mm)
2
13
/
16
"
(71mm)
2
1
/
8
"
(54mm)
3
1
/
8
"
(79mm)
/