Dorel Home Furnishings DE65757 Owner's manual

DO NOT RETURN TO THE STORE !

Visit www.dhpfurniture.com/eng/support-home

or call Toll-Free 1-800-267-1739

4029029

B34402902900 - 10125-M

Date of Purchase

Rose Upholstered Bed

N.C. - 12/16/2016

If parts are missing or damaged, we will gladly ship your

replacement parts free of charge.

Lot Number

Thank you for purchasing from DHP!

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

1

Full

Black Linen

Weight Limit: 450 Lb / 204 Kg

TM

Contact Us!

[email protected]

Read Before Beginning Assembly

1-800-267-1739

Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)

DHP Consumer Services

12345 Albert Hudon, Suite 100.

Montreal, Quebec, Canada H1G 3L1

Warranty Information

2

B34402902900

Caution

DHP warrants this product to be free from defects in material and workmanship and

agrees to remedy any such defect. This warranty covers one year from the date of

original purchase. This is solely limited to the repair or replacement of defective

parts and assembly labor is not included.

This warranty does not apply to any product which has been improperly assembled,

subjected to misuse or abuse or which has been altered or repaired in any way.

Liability for consequential damages is excluded to the extent exclusion is permitted

by law. This warranty gives you specific legal rights and you may also have other

rights which vary from state to state.

To obtain warranty service, purchaser must present original bill of sale. Components

repaired or replaced are warranted through the remainder of the original warranty

period only. The defective components will be repaired or replaced without charge,

subject to the terms and conditions described above.

Visit www.dhpfurniture.com

to view the limited warranty valid in the U.S. and

Canada.

●

Ca

ll our toll free number if you need assistance.

●

W

ork in a spacious area and near where the unit will be used, preferably on a

carpet, or use a piece of the cardboard packaging to protect your floor and prod

uct.

● Re

commended # of people needed for assembly: 2 (however it is always better

to have an extra hand). Estimated assembly time is 2 hours.

●

Ma

ke sure all parts are included. Most parts are labeled or stamped on the ra

w

ed

ge.

●

Re

ad each step carefully. It is very important that each step of the instructio

ns is

p

erformed in the correct order. If these steps are not followed in sequence

,

assembly difficulties will occur.

●

This pro

duct is designed for home use and not intended for commercial use.

●

Thi

s product contains small components. Please ensure that they are kept away

from small children

.

● Do

not use power tools to assemble your furniture. Power tools may strip or

damage the parts.

For help with assembly, identifying parts, product information or to order parts,

please contact us:

Page is loading ...

4

Parts

B34402902900

All in 1 big box!

Before you throw the package, please use the

Check Box to identify the parts and ensure that

you have all the parts needed for the assembly.

There are inner box(es) that include components

required to complete this assembly.

Replacement Parts, Visit www.dhpfurniture.com/eng/support-home

A

B

A1

C

D

J

I

H

G

F

P

N

M

L

K

Side Panel

T944030

X 2

Side Panel

T944040

X 2

Headboard

T944010

X 1

Back Panel

T927010

X 1

Footboard

T944020

X 1

Center Rail

T926710

X 1

Center Rail

T926700

X 2

Side Rail

T926680

X 4

Side Rail

T926670

X 2

Side Rail

T926690

X 2

Wooden Slats

T926770

X 24

Corner Bracket

T393110

X 4

Support Leg

T926660

X 2

Support Leg

T926730

X 2

Cross Brace

T927040

X 1

S

T

X

Y

Z

Left Bracket

T393080

X 2

Right Bracket

T393090

X 2

Single Slat Cap

T926370

X 24

Double Slat Cap

T926380

X 12

Leg

T

941620

X 4

A

B

C

D

C

D

F

G

H

Z

L

I

J

M

K

I

T

S

N

X

Y

P

5

Hardware Pack

B34402902900

Hardware Pack #: T4107119-00

Hardware Note:

Please do not completely tighten all the hardware,

until the entire assembly is complete, unless

otherwise indicated in the step-by-step

instructions.

The screw(s), bolt(s) to be used at each step are

shown in actual size in the lower right corner of

the page.

6

7

8

4 5

3

2

1

1/4" X 3/4"

X 40

1/4" X 1 3/8"

X 6

1/4" X 1 9/16"

X 28 1/4" X 1 3/4"

X 3

5/16" X 2 1/4"

X 4

4mm

X 1

Wrench

X 1

1/4"

X 3

6

B34402902900

Step

1

The slat holes on part F

should be facing upward.

Attach F and H to C and D with .

Repeat the same step for remaining parts

C, D, F and H.

X 16

3

C

F

3

D

H

C

F

3

7

B34402902900

Step

2

The slat holes on part G

should be facing upward.

X 12

3

Attach G x 2 to previous subassembly C

and D with .

Repeat the same step for remaining parts

G.

C

D

G

D

G

3

8

B34402902900

Step

3

X 12

1

Attach S to D and T to C with .

Repeat the same step for the other

subassembly C and D.

C

D

S

T

C

1

G

D

S

T

G

1

9

B34402902900

Step

4

Stick A1 to the back of A with Velcro as

illustrated.

A1

A

10

B34402902900

Step

5

1

B

A

B

X 4

Screw into A and into B, leave

half of the bolts exposed.

Do not completely tighten

the BOLTS, leave half of

the length exposed.

2

1

2

X 4

1

11

B34402902900

Step

6

Hang C and D on A and B as illustrated,

don't completely tighten the BOLTS until

STEP 10 is complete.

A

C

D

C

B

T

C

A

2

12

B34402902900

Step

7

Attach N to Z with .

Repeat this step for all remaining legs Z.

X 4

5

Z

N

5

13

B34402902900

Step

8

8.1 Attach N x 4 to A ,B, C AND D with ;

8.2 Attach L x 2 to H with .

X 2

2

X 16

1

8.1

8.2

1

Z

N

A

C

2

H

L

D

C

D

L

H

A

N

Z

L

1

2

14

B34402902900

Step

9

Holes on part I and J should be facing upward.

1

X 4

Insert I x 2 and J into M x 2, then fix them

with .

I

M

J

I

J

I

M

1

15

B34402902900

Step

10

Attach subassembly from previous STEP to

A and B with , then properly

tighten all the Bolts.

1

X 4

A

I

A

I

J

1

16

B34402902900

Step

11

Attach K to F x 2 and J with and .

X 3

4

X 3

4

F

K

F

7

8

J

46

6

17

B34402902900

12.1

12.2

12.3

X

P

F

G

X

P

Y

A

G

I

A

X

Y

P

I

Step

12

12.1 Insert P into X;

12.2 Press

X into F and G, repeat the

same procedure for the opposite side.

12.3 Insert ends of both slats P into Y,

then press Y into I and J as illustrated.

Repeat the same procedures going

backwards for every row of slats.

J

I

G

18

Helpful Hints

B34402902900

● Move your new furniture carefully, with two

pe

ople lifting and carrying the unit to its ne

w

lo

cation

.

● Y

our DHP furniture can be disassembled an

d

reassembled to move.

● S

ome parts have been pre-assembled for this

item. They are illustrated on this page and availabl

e

for re

placement.

WARNINGS:

For safety reasons and to prevent injuries:

●

Thi

s bed is not intended for use by children under 4

years old.

●

P

rohibit jumping and horseplay on this bed.

●

Onl

y use a mattress which is 74" - 75" long and 53"

- 54"

wide.

●

D

o not use risers under this bed.

Helpful Hints

Weight Limit: 450 Lb / 204 Kg

END CAP

T393120

X 2

END CAP

T392520

X 2

Page is loading ...

Dorel Home Furnishings DE65757 Owner's manual

Dorel Home Furnishings DE65757 Owner's manual

in other languages

Related papers

Other documents