AE T4.2 Factory Team Kit Assembly Manual

Brand: AE

Model: T4.2 Factory Team Kit

Category: Remote controlled toys

Type: Assembly Manual

This manual is also suitable for

RC10 T4.2

3/13

:: Introduction

:: KIT Features

:: Additional

:: Other Helpful Items

Associated Electrics, Inc.

26021 Commercentre Dr.

Lake Forest, CA 92630

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

Customer Service

Tel: 949.544.7500

Fax: 949.544.7501

Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and

maintaining your new RC10 T4.2. Please take a moment to read through this manual to help familiarize yourself with these steps.

We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the

illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these

sheets before you start to build.

Features in the T4.2 Factory Team:

• Factory Team 12mm “Big Bore” hard anodized, threaded aluminum shocks with TiN “Gold” 3mm shock shafts

• VTS slipper (variable torque, multi-plate slipper with 3 drive surfaces) and high-resolution spring

• Factory Team blue aluminum steering bellcrank set

• Factory Team 12mm blue aluminum front and rear clamping hexes with hex drive wheels

• “Gull-wing” front suspension arms and updated front and rear shock towers optimized for12mm big bore shocks

• Factory Team 7075-T6 blue aluminum 0° rear hubs with oversized outer bearing

• Pro-Line Bulldog body

• CVA joints with pin retainer clips

• Ball differential with light-weight outdrives

• Factory Team carbon fiber battery strap and blue aluminum thumb screws

• Complete set of precision ball bearings

• Factory Team blue titanium turnbuckles, blue aluminum hinge pin brace, milled motor plate, servo mounts, rear ballast weight

and much more!

Your new T4.2 FT kit comes unassembled

and requires the following items for completion

(refer to catalog section for suggestions):

• R/C two channel surface frequency radio system

• AA-size batteries for transmitter

(#302 alkaline, #303 rechargealble)

• Electronic Speed Control, ESC (#29140, #29143)

• Steering servo (#29166, #29167) • R/C electric motor

• Pinion gear, size determined by type/wind of motor

• Battery charger (a peak detection charger, or LiPo compatible charger)

• 6 cell NiMH battery pack (#700) or a 2 cell LiPo battery pack (#714)

• Calipers or a precision ruler • Needle nose pliers

• Lexan specific spray paint

• Reamer / hole punch

• Cyanacrylate glue (#1597)

• Thread locking compound (#1596)

• Tires and Inserts, Fronts and Rears

Tools included:

• Allen wrenches #6950 (.050”, 1/16”, 3/32”, 5/64”)

• Molded tools #6956

• Camber gauge #1719

• Silicone Shock Fluid (Refer to catalog for complete listings)

• Body Scissors (AE Part # 1737) • Reamer / Hole Punch • Wire Cutters • Hobby Knife

• FT Hex Wrenches (AE Part # 1655) • Needle Nose Pliers • Multi Tool (AE Part #7494)

• Soldering Iron • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)

:: Table of Contents

:: Notes

This symbols indicates a

special note or instruction

in the manual.

There is a 1:1 hardware foldout page in the back

of the manual. To check the size of a part, line

up your hardare with the correct drawing until

you find the exact size. Each part in the foldout

has a number assigned to it for ordering

replacement parts.

1................... Cover

2................... Introduction

3................... Table of Contents

4................... Steering Build

(Bag A-AA)

4 - 5............. Front End, Outer Build

(Bag B-BB)

5 - 6............. Front End, Inner Build

(Bag C)

6 - 9............. Transmission Build

(Bag D-DD)

9 - 11........... Rear End Build

(Bag E-EE)

11 - 12........ CVA and Turnbuckle Build

(Bag F-FF)

12 - 14........ Shocks Build

(Bag G-GG)

14 - 16........ Electronics Build

(Bag H-HH)

16 - 17........ Wheels, Tires and Body Install

(Bag I)

17................. Servo Chart

18 - 19....... Tuning Tips

20 - 29....... Catalog

30................ Notes

31................ Setup Sheet “Kit Setup”

32................ 1:1 Hardware “Fold Out”

33................ Setup Sheet “Blank”

34................ Back Cover

Associated Electrics, Inc.

26021 Commercentre Dr.

Lake Forest, CA 92630

http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook

Customer Service

Tel: 949.544.7500

Fax: 949.544.7501

:: Steering Build - Bag A-AA - Step 2

:: Front End, Outer Build - Bag B-BB - Step 1

:: Steering Build - Bag A-AA - Step 1

Install the C Clip

into the groove

shown below.

Do not overtighten steering bolts. Make sure

there is free movement in the steering rack.

Build 2 (1 left, 1 right) Build 2!

9659

Steering

brace

9640

Steering

bolt

(left)

6272

Dust cover

foam

9647

Block carrier

bushing

3981

Ballstud, .20

black, short

6276

Ballstud, .20

silver, short

6917

4-40x3/8

bhcs

6272

Dust cover

foam

9679

FT Aluminum

Bellcrank Set

3971

Steering rack

bearing

9566

Top plate

9640

Steering

bolt

(right)

9659

Steering

rack

Be careful to not get

thread lock on steering

rack bushings!

6272

Dust cover

foam

31286

FT ballstud

washer,

aluminum

(2mm)

9880

Steering

block, hex

6277

Ballstud, .30

silver, long

4449

4-40x3/16

aluminum

locknut

#1596

thread lock

6922

4-40x1/2

fhcs

6915

4-40x5/8

fhcs

7440

T4 chassis

89229

Blue

countersunk

washer

9563

Front

bulkhead

7854

T4 front

axle, hex

3977

3/16x3/8

bearing

9882

C-clip, 3/16

:: Front End, Outer Build - Bag B-BB - Step 2

:: Front End, Outer Build - Bag B-BB - Step 3

:: Front End, Inner Build - Bag C - Step 1

6272

Dust cover

foam

Align the C-clip on

the front axles

with the D-shape

inside the

steering blocks.

7922

Caster block,

30°

(1 left, 1 right)

3983

Ballstud, .30

black, short

4449

4-40x3/16

aluminum

locknut

foam

with the D-shape

steering blocks.

3977

3/16x3/8

bearing

9898

2-56x3/16

shcs

9892

12mm aluminum

clamping wheel

hex, rear

7369

1/16

universal

roll pin

9645

2-56x1/8

bhcs

9645

2-56x1/8

bhcs

7922

Spacer

9622

Hinge pin,

front outer

9622

Hinge pin,

front outer

91201

SC10B

a-arms,

front

9665

FT front

hinge pin

brace

9621

Hinge pin,

front inner

9562

Front

bumper

6915

4-40x5/8

fhcs

4334

2-56x5/16

bhcs

:: Front End, Inner Build - Bag C - Step 2

:: Front End, Inner Build - Bag C - Step 3

:: Transmission Build - Bag D-DD - Step 1

7666

Drive

rings

9852

Ball diff

outdrives

9852

Ball diff

outdrives

7666

Drive

rings

6581

3/32 carbide

diff balls

7664

Diff gear

52T

x12

Ball diff

outdrives

rings

#6591

diff lube

#6591

diff lube

#6591

diff lube

7413

4-40x3/4

bhcs

91202

SC10B

front shock

tower

1780

FT aluminum

shock bushings,

standard

6924

4-40x3/8

shcs

6925

4-40x1/2

shcs

6277

Ballstud .30

silver, long

31286

FT ballstud washer,

aluminum (2mm)

6272

Dust cover

foam

7439

Front body

mount

#1596

thread lock

Orient the notch

to the left

throughout the

car. It indicates

which end has the

left hand threads!

Front Camber Turnbuckle

1.92” (48.75mm)

2.07” (52.75mm)

Steering Turnbuckle

7230

ball cup

(large)

7230

ball cup

(large)

1417

2.80”

turnbuckle

1408

2.65”

turnbuckle

:: Transmission Build - Bag D-DD - Step 2

:: Transmission Build - Bag D-DD - Step 3

:: Transmission Build - Bag D-DD - Step 4

As you tighten the diff bolt, you will notice the T-nut ears moving

closer to the bottom of the outdrive slot. This compresses the

spring behind the T-nut. The spring should be completely com-

pressed at the same time the T-nut reaches the end of the slot.

Caution! Pay close attention to the feeling when the spring is

completely compressed. Do not overtighten the bolt. When you

feel the spring completely compressed, loosen the diff bolt 1/8”

of a turn. Your diff should now operate smoothly with resistance

as the outdrives move in opposite directions. After you have

driven the car once, re-check the diff setting.

9601

Top shaft

9602

Top shaft

spacer

9826

Transmission case

(1 left, 1 right)

3977

Ball bearing

3/16x3/8

9361

Idler gear

shaft

9360

Idler gear

3977

Ball bearing

3/16x3/8

9832

Ball bearing

10x16mm

6575

Diff

cover

6575

Locking

t-nut

6582

Diff

thrust

spring

#6588

black grease

6573

Diff thrust

washer

6589

5/32 x 5/16,

unflanged

bearing

6574

5/64 diff

thrust

balls

6573

Diff thrust

bolt

:: Transmission Build - Bag D-DD - Step 5

:: Transmission Build - Bag D-DD - Step 6

:: Transmission Build - Bag D-DD - Step 7

7485

FT V2

slipper hub

91177

VTS

slipper

pads

9603

Slipper

pad

9653

84T 48P

spur gear

91176

VTS slipper

housing

91178

VTS slipper

plate

91179

VTS slipper

hub, outer

#1596

thread lock

#1596

thread lock

6919

4-40x5/16

bhcs

6925

4-40x1/2

shcs

6913

4-40x1 1/4

shcs

1770

FT milled

motor plate

(blue)

6928

4-40x1

shcs

9587

Wing mounts

(1 left, 1 right)

9819

Motor

guard

9630

.030 ballstud

washer

There’s also a 75T

48P Spur Gear

(#9650)

included for stock

motors use!

Install the Diff with

the head of the

Diff Thrust Bolt

(#6573) facing the

right side of the

transmission case!

:: Transmission Build - Bag D-DD - Step 8

:: Rear End Build - Bag E-EE - Step 1

:: Rear End Build - Bag E-EE - Step 2

Set nut

flush with

top shaft.

See page 18 for gear

mesh, and slipper clutch

setting instructions!

6629

5-40

locknut

9739

Slipper

spring

7486

V2 slipper

washer

Compress

spring first.

7487

Anti-squat shim

(2 degrees)

9621

Hinge pin,

rear inner

7448

Rear T4 a-arms

(1 left, 1 right)

9645

2-56x1/8

bhcs

9818

Rear chassis

plate

7487

Rear arm

mount

(3.0 degree)

9269

5-40x1/2

fhcs

9269

5-40x1/2

fhcs

:: Rear End Build - Bag E-EE - Step 3

:: Rear End Build - Bag E-EE - Step 4

:: Rear End Build - Bag E-EE - Step 5

6277

Ballstud .30

silver, long

9564

Rear chassis

brace

31286

FT ballstud

washer,

aluminum

(1mm)

6272

Dust cover

foam

Use inside hole in

chassis brace!

9643

5-40x7/16

shcs

7488

Rear ballast

weight

9644

5-40x9/16

shcs

7413

4-40x3/4

bhcs

9643

5-40x7/16

shcs

1781

FT aluminum

shock bushing,

short

9824

T4 rear shock

tower

#1596

thread lock

6922

4-40x1/2

fhcs

:: Rear End Build - Bag E-EE - Step 6

:: CVA and Turnbuckles Build - Bag F-FF - Step 1

:: CVA and Turnbuckles Build - Bag F-FF - Step 2

Build x2 (right and left side)

1 drop!

CA glue not

included

Align the gap in

the pin retainer

to be opposite of

the CVA pin.

#1597

ca glue

Build x2

9864

FT aluminum

hub ( 0˚)

4449

4-40x3/16

aluminum

locknut

6272

Dust cover

foam

3981

Ballstud, .20

black, short

9917

Aluminum

hub A,

carbon

Left Side

6288

4-40x1/4

bhcs

6924

4-40x3/8

shcs

6915

4-40x5/8

fhcs

3977

3/16x3/8

bearing

7933

Crush tube

7935

.187x.196

bearing

7368

3/16 axle

shim

7381

CVA coupler

7996

CVA pin

retainer

9755

CVA axle

rear

9596

FT CVA bone

(T4)

7381

CVA cross

#6588

black grease

:: CVA and Turnbuckles Build - Bag F-FF - Step 3

:: CVA and Turnbuckles Build - Bag F-FF - Step 4

:: Shocks Build - Bag G-GG - Step 1

Build x2 (right and left side)

Build x2

(right and left side)

Build x2 (right and left side)

Orient the notch

to the left

throughout the

car. It indicates

which end has the

left hand threads!

91308

12mm shock

piston

(1.6 front)

(1.7 rear)

91306

27.5x3 TiN

shock shaft

(front)

91307

35x3 TiN

shock shaft

(rear)

6299

1/8 E-clip

6299

1/8 E-clip

4187

Nylon spacer,

(.030)

Racers Tip:

Use a marker over the

numbers on the pistons to

make them easily visible!

Front:

4 spacers

Rear:

2 spacers

Build x2

(right and left side)

Orient the notch

which end has the

left hand threads!

2.10” (53.5mm)

Steering Turnbuckle

7230

ball cup

(large)

1417

2.80”

turnbuckle

7369

1/16

roll pins

9892

12mm aluminum

clamping wheel

hex, rear

9898

2-56x3/16

shcs

9645

2-56x1/8

bhcs

31286

FT ballstud

washer,

aluminum

(1mm)

9622

Hinge pin,

rear outer

9630

.030 ballstud

washer

:: Shocks Build - Bag G-GG - Step 2

:: Shocks Build - Bag G-GG - Step 3

:: Shocks Build - Bag G-GG - Step 4

1777

FT shock

pivot ball

1777

Shock

eyelet

#1105

green slime

91300

12x27.5mm

shock bodies

(front)

91302

12x36mm

shock bodies

(rear)

91309

Shock hat

bushing

91309

Shock

spacer

5407

O-ring

31327

VCS3 shock

bottom cap

31327

VCS3 shock

bottom cap

o-ring

91309

12mm shock

cap o-ring

#1105

green slime

Racers Tip:

Lightly rub shock oil on the

o-ring before installation!

Racers Tip:

Coating the o-rings

with green slime

(#1105) helps seal

& reduce o-ring

swell! Green slime

not included in kit!

91303

12mm

shock cap

Step 9-10Step 8Step 6-7Step 4-5

Front Shock: 35 wt

Rear Shock: 35 wt

Step 2-3

31510

M2x4mm

bhcs

91309

Shock cap

o-ring

Shock Bleeding Steps:

1. Before assembly, get each bleed

screw and thread it 1-2 turns into the

shock cap. This will make installation

easier when you are bleeding your

shocks.

2. Pull shock shaft down.

3. Fill shock body 3/4 full with silicone

shock fluid.

4. Slowly move the shock shaft up and

down to remove air from under the

piston.

5. Wait for bubbles to come to surface.

6. Fill shock body to top with silicone

shock fluid.

7. Place a drop of oil in the cap and on

cap threads.

8. Install cap (without bleed screw) and

tighten completely.

9. Slowly compress shaft all the way to

bleed excess silicone shock fluid out

the hole in the cap (use rag around-

shock to catch excess fluid).

10. Install M2x4mm button head screw

until snug while shaft is fully com-

pressed.

Shock oil

#5429

Shock oil

#5429

91310

12mm shock

spring cup

(9mm offset)

91329

12mm front

spring, Gray

(3.45lb)

91336

12mm rear

spring, Green

(2.00lb)

91304

12mm

threaded

collar

91304

12mm

threaded

collar

o-ring

Front:

8mm

Rear:

8.5mm

Build x2 front and x2 rear shocks

Racers Tip:

Use your finger to rub

shock oil on the o-ring for

smoother adjustment!

:: Shocks Build - Bag G-GG - Step 5

:: Electronics Build - Bag H-HH - Step 1

:: Electronics Build - Bag H-HH - Step 2

Offset the servo horn by

5-10 degrees

(approximately one notch)

Offset the servo horn by

5-10 degrees

(approximately one notch)

9170

Servo link

7337

Gold

washer

89007

Servo horn

ring

3981

Ballstud, .20

black, short

6272

Dust cover

foam

9180

Servo

horn

1779

FT Servo

mount

7336

Servo

spacers

6917

4-40x3/8

bhcs

Servo not

included!

Servo screw

not included!

Leave a

2mm gap!

See page 17 for correct

servo spacing on the

servo chart!

6292

4-40x3/8

fhcs

Use outside

hole in

front arm!

6472

Shock

mount nut

6925

4-40x1/2

shcs

Use inside

hole in

rear arm!

6927

4-40x3/4

shcs

6472

Shock

mount nut

:: Electronics Build - Bag H-HH - Step 3

:: Electronics Build - Bag H-HH - Step 4

:: Electronics Build - Bag H-HH - Step 5

Receiver / Servo tape

not included!

6338

Antenna

tube & cap

3862

5-40x1/8

set screw

ESC/ Servo tape

not included!

See page 18 for

gear mesh setting

instructions!

7461

Gear cover

(clear)

7461

Gear cover

button

6285

4-40x1/4

shcs

7461

Gear cover

(clear)

Pinion / Setscrew

not included!

Motor not included!

6936

Washer #4

aluminum

31532

M3x8mm

bhcs

:: Electronics Build - Bag H-HH - Step 6

:: Wheels / Tires and Body - Bag I - Step 1

Tires / Inserts

not included!

7852

Truck wheel

hex, white

Carefully apply ca

glue to the tire bead.

Do one side at a

time, allow it to dry

before gluing the

other side!

7452

Battery strap,

carbon

1787

4-40x1/2

set screw

1787

FT battery

strap thumb

screws

9238

Foam

battery

spacer

x2x2

Battery

not included!

#1597

ca glue

#1597

ca glue

6953

8-32

LP steel

locknut

:: Wheels / Tires and Body - Bag I - Step 2

:: Wheels / Tires and Body - Bag I - Step 3

:: Servo Chart

Painting Tips:

Body :

Your vehicle comes with a clear polycarbonate body.

You will need to prep the body before you can paint

it. Wash the inside thoroughly with warm water and

liquid detergent. Dry the body using a clean, soft,

lint-free cloth. Use the supplied window masks to

cover the windows from the INSIDE of the body

(RC cars get painted from the inside).

Using high quality masking tape, apply tape to the

inside of the body to create a design. Spray (either

rattle can or airbrush) the paint to the inside of the

body (prefferably dark colors first, lighter colors last).

NOTE: use ONLY paint that is recommended for use

with (polycarbonate) plastics. If you don’t, you can

destroy the plastic body!!!!).

After painting, cut the body along the trim lines. Make

sure to drill or use a body reamer to make the holes

for the body mounts and antenna!

Steering Servo Chart

Associated

* Not all servo’s are listed

* Make sure servo linkage clears the servo through full travel in both directions.

Use #7336 servo spacers to adjust the servos position

(to make the steering link as straight as possible)

XP-1015, XP-1313

# 9180

servo arm

94102

HS-5625MG, HS-5645MG, HS645MG

Z4750, Z2750

Z250, Z550

S9204, S9250, S9450

S9404

94257, 94258, 94357,

94358, 94452, 94453, 94755

HS-965, HS-985MG,

HS-5965, HS-5985MG

PS-401, PS-2001, PS-2004, PS-2015, PS-2173,

PS-2174, PS-2123, PS-2143, PS-2144

Airtronics

Hitec

Futaba

6332

Body

clips

Front

6952

8-32

locknut,

steel

Front

9587

Wing

shims

:: Tuning Tips

Tips for Beginners:

Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes

to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps.

Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing

it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup

sheet (make adddtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to

the previous setup and try another change.

When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this as a guide for future

track days or conditions.

Peridicaly check all moving suspension parts. Suspension components must be kept clean and move freely without

binding to prevent poor and/or inconsistent handling.

Motor Maintenance:

Brushed motors require frequent maintenance to keep performance levels at their maximum. Between runs and after

letting the motor cool completely, inspect the brushes to ensure that they are moving freely in their holders.

Remove the springs and slide the brushes in and out of their holders checking for any resistance or rough spots.

If found, remove the brush and carefully wipe it clean. Removing buildup will allow the brush to slide freely and create

maximum contact with the commutator resulting in maximum power output.

After every 3-5 runs, remove the brushes from their holders and inspect the tips for wear or burning. If there is

noticeable wear (less than 75% of the brush remaining), it is best to cut the commutator and replace the brushes with

a new pair. If the tips become a burned blue color, the lubricant in the brush has been burned away and new brushes

should be installed.

Occasionally, the motor should be cleaned with a soft brush to prevent dirt build up around the brush hood area and ball

bearings. At this time, it is a good idea to add one drop of bushing / bearing oil to each bushing or ball bearing.

If using a brushless motor, please refer to the motor manufacturer’s guidelines for proper maintenance.

Slipper Clutch:

The assembly instructions give you a base setting for your clutch. Turn the nut on the shaft so that the end of the top

shaft is even with the outside of the nut. At the track, tighten or loosen the nut in 1/8 turn increments until you hear

a faint slipping sound for 1-2 feet on takeoffs. Another popular way to set the clutch is to hold both rear tires firmly in

place and apply short bursts of throttle. If the clutch is properly set, the front tires should lift slightly up off the surface.

Motor Gearing:

Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and

premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used motor

types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your motor and

electronic speed control manufacturers for more information. Team Associated is not responsible for motor damage

due to improper gearing. * These gearings are for use with advanced timing speed control settings!

Set The Gear Mesh:

You should be able to rock the spur gear back and forth in the teeth of the pinion gear without making the pinion gear

move. If the spur gear mesh is tight, then loosen the #31532 screws and move the motor away, then try again.

A gear mesh that is too tight or too loose will reduce power and damage the gear teeth.

27T Reedy Stock

19T Reedy Super Stock

17.5 Reedy Sonic Brushless *

17.5 Reedy Sonic Brushless

13.5 Reedy Sonic Brushless *

13.5 Reedy Sonic Brushless

10.5 Reedy Sonic Brushless

9.5 Reedy Sonic Brushless

8.5 Reedy Sonic Brushless

7.5 Reedy Sonic Brushless

6.5 Reedy Sonic Brushless

3300kV Brushless

3900kV Brushless

4900kV Brushless

6100kV Brushless

10.92:1

11.49:1

10.40:1

7.501

11.49:1

8 .111

10.40:1

10.921

11.49:1

12.13:1

12.85:1

Motor Pinion Spur FDR

T4.2 Gear Ratio Chart (Internal Gear Ratio 2.60:1)

:: Tuning Tips (cont.)

Front Camber Links:

Changing the length of the camber link is considered a bigger step than

adjusting the ball end height on the tower. Shortening the camber link

(or lowering the ball end) will give the front end less roll and quicken steering

response. Lengthening the camber link (or raising the ball end) will give the

front more roll and slower steering response. Longer camber links are

typically used on high grip tracks and shorter links tend to work better on

medium-grip loose tracks.

*Raise or lower the

ball end by adding

or subtracting

washers here

Caster:

Caster describes the angle of the kingpin as it leans toward the rear of the vehicle. Positive caster means the kingpin

leans rearward at the top. The supplied 30° caster blocks (#7922) are recommended in most cases.

For less corner entry steering and more exit steering, try the optional 25° blocks (#7919).

Rear Camber Link:

Changing the length of the camber link is considered a bigger step than adjusting

the ball end height on the rear chassis brace. Shortening the camber link

(or lowering the ball end) will give the rear end less roll and the car will tend to

accelerate or “square up” better. Lengthening the camber link (or raising the ball

end) will give the rear more roll and more cornering grip. Longer camber links are

typically used on high grip tracks, while shorter links tend to work better on

medium grip loose tracks. The kit setting is the best compromise of cornering grip

and acceleration.

Wheelbase Adjustment:

You have three options for rear hub spacing, Forward, Middle, & Back.

The kit setting provides the most rear traction, and will be used most often.

For improved handling in bumps or rhythm sections, try moving the hubs to the

Middle or Back position. This can also make the car handle better in 180° turns.

Rear Camber:

Camber describes the angle at which the tire and wheel rides when looked at from the back. Negative camber means

that the tire leans inward at the top. A good starting camber setting is -1°. Use the included #1719 camber gauge to

set your camber. Adding a small amount of positive camber, where the top of the tire is leaning out, will tend to improve

straight-line acceleration on loose tracks.

Anti-Roll Bars:

The optional #9635 rear anti-roll bar kit (also called the “swaybar”) allows you to add roll resistance to the rear end with

minimal effect on handling over bumps and jumps. It is an especially helpful tuning item on high-grip tracks

(try the gold bar). The silver and black anti-roll bars are typically used on medium-grip loose tracks.

Ride Height:

Ride height is the distance from the ground to the bottom of the

chassis. The standard front ride height setting is with the inner

and outer hinge pins of the front arms level on the same imaginary

horizontal line, or 30mm as measured from the bottom of the

chassis directly behind the front bumper.

The rear ride height setting you should use most often is with the

outdrive, driveshaft, and axles all on the same imaginary horizontal

line (reffered to as “bones level”) or 28mm.

Check the ride height by lifting up the entire car about 8-12 inches

off the bench and drop it. After the suspension “settles” into place,

measure ride height (Ride Height Gauge #1449). Raise or lower

the shock collars as necessary.

Front Camber:

Camber describes the angle at which the tire and wheel rides when

looked at from the front. Negative camber means that the tire leans

inward at the top. A good starting camber setting is -1°. Use the

included #1719 camber gauge to set your camber. Positive camber,

where the top of the tire is leaning out, is not recommended.

*Testing camber

with camber gauge

*Raise or lower

the ball end by

adding or

subtracting

washers here

*Spacers to the rear

will place hubs for-

ward, shortening

the wheelbase

*Front arms

inner and outer

hinge pins should

be in a imaginary

horizontal line

when ride height

is set

*CVA bones should

be in a straight line

when ride height is

set at “CVA bones

level”

*Spacers to the rear

:: Shocks

:: Shock Springs

:: Ball Differential

:: Shock Oil

1777

4187

5407

6299

31327

31510

91300

91302

91303

91304

91306

91307

91308

91309

91310

91315

91317

4 ea.

2 ea.

4 ea.

91325

91326

91327

91328

91329

91330

91331

91332

91333

91334

91335

91336

91337

91338

91339

91340

91341

91342

91343

91344

91345

Pr.

5420

5421

5422

5423

5424

5425

5426

5427

5428

5429

5430

5431

5432

5433

5434

5435

5436

5437

5438

2oz.

6573

6574

6575

6581

6582

6589

7664

7666

7677

9852

9853

FT Blue Aluminum Shock Pivot Ball with Eyelet

.030 Nylon Washer

Red O-Rings

E-Clip

VCS3 Shock Bottom Cap and O-Ring

M2 x 4mm BHCS

12X27.5mm FT Shock Bodies (front)

12X36mm FT Shock Bodies (rear)

12MM Shock Cap

12MM Threaded Collar and O-Ring

27.5X3mm TiN Shock Shaft (front)

35X3mm TiN Shock Shaft (rear)

12MM Shock Pistons, (1.5, 1.6, 1.7)

12MM Shock Rebuild Kit

12MM Shock Spring Cups (+0mm, +5mm, +9mm)

12MM Shock (T4/SC10 Front)

12MM Shock (T4/SC10 Rear)

12MM Front SPRING BRN 2.85

12MM Front SPRING BLK 3.00

12MM Front SPRING GRN 3.15

12MM Front SPRING WHT 3.30

12MM Front SPRING GRY 3.45 - Kit

12MM Front SPRING BLU 3.60

12MM Front SPRING YLW 3.75

12MM Front SPRING RED 3.90

12MM Front SPRING ORN 4.05

12MM Front SPRING PRL 4.20

12MM Rear SPRING BLK 1.90

12MM Rear SPRING GRN 2.00 - Kit

12MM Rear SPRING WHT 2.10

12MM Rear SPRING GRY 2.20

12MM Rear SPRING BLU 2.30

12MM Rear SPRING YLW 2.40

12mm Big Bore Front Soft Spring Kit

12mm Big Bore Front Medium Spring Kit

12mm Big Bore Front Hard Spring Kit

12mm Big Bore Rear Soft Spring Kit

12mm Big Bore Rear Medium Spring Kit

10 Weight Silicone Shock Oil

20 Weight Silicone Shock Oil

30 Weight Silicone Shock Oil

40 Weight Silicone Shock Oil

22.5 Weight Silicone Shock Oil

80 Weight Silicone Shock Oil

27.5 Weight Silicone Shock Oil

15 Weight Silicone Shock Oil

25 Weight Silicone Shock Oil

35 Weight Silicone Shock Oil

45 Weight Silicone Shock Oil

55 Weight Silicone Shock Oil

32.5 Weight Silicone Shock Oil

37.5 Weight Silicone Shock Oil

42.5 Weight Silicone Shock Oil

50 Weight Silicone Shock Oil

60 Weight Silicone Shock Oil

70 Weight Silicone Shock Oil

47.5 Weight Silicone Shock Oil

Diff Thrust Washer & Bolt

Precision Diff Thrust Balls, 5/64”

Locking T-Nut, Diff Thrust Bolt, & Cover

3/32” Carbide Diff Balls

Diff Thrust Spring

Ball Bearing, 5/32 x 5/16” unflanged

Diff Gear 52T

Diff Drive Rings, 2.60:1

B4 / T4 / GT Diff Rebuild Kit

SC10 Ball Diff Outdrives

SC10 Complete Ball Differential

6299

91304

91310

31327

5407

91303

91309

31510

91306

91307

91300

91302

4187

1777

91308

6575

9853

6582

9852

7666

6589

6581

7664

6589

7666

9852

6573

6574

6575

Page is loading ...

AE T4.2 Factory Team Kit Assembly Manual

Brand: AE

Model: T4.2 Factory Team Kit

Category: Remote controlled toys

Type: Assembly Manual

This manual is also suitable for

RC10 T4.2

Download PDF

report

AE T4.2 Factory Team Kit Assembly Manual

This manual is also suitable for

AE T4.2 Factory Team Kit Assembly Manual

Related papers

Other documents