INSTALLATION INSTRUCTIONS
VALIANT SERIES POST TOP LED VERSION
American Electric Lighting a division of Acuity Lighting Group, Inc. Granville, OH
DRAWING NO. A68128 REV A (FRONT)
©2011 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-71-68128
OPENING & CLOSING THE UNIT:
OPENING & CLOSING THE UNIT:
1. OPEN THE UNIT. (SEE “OPENING AND CLOSING THE UNIT”
1. OPEN THE UNIT. (SEE “OPENING AND CLOSING THE UNIT”
ABOVE.)
ABOVE.)
2. UNSCREW THE TWO SCREWS ATTACHING THE REFLECTOR
2. UNSCREW THE TWO SCREWS ATTACHING THE REFLECTOR
PLATE ASSEMBLY TO THE HOOD. (SEE FIGURE 2).
PLATE ASSEMBLY TO THE HOOD. (SEE FIGURE 2).
3. HOLD THE REFLECTOR PLATE AND MOVE BACKWARDS.
3. HOLD THE REFLECTOR PLATE AND MOVE BACKWARDS.
UNSCREW THE SCREW ATTACHING THE TETHER.
UNSCREW THE SCREW ATTACHING THE TETHER.
4. DISCONNECTING THE WIRING BY USE OF THE QUICK
4. DISCONNECTING THE WIRING BY USE OF THE QUICK
DISCONNECT.
DISCONNECT.
5. TO REINSTALL THE REFLECTOR PLATE ASSEMBLY REPEAT THE
5. TO REINSTALL THE REFLECTOR PLATE ASSEMBLY REPEAT THE
STEPS ABOVE IN REVERSE ORDER.
STEPS ABOVE IN REVERSE ORDER.
1. UNSCREW 2 SCREWS ATTACHING THE BASE COVER TO THE
1. UNSCREW 2 SCREWS ATTACHING THE BASE COVER TO THE
UNIT.
UNIT.
2. LIFT THE BASE COVER FREE.
2. LIFT THE BASE COVER FREE.
3. TO REINSTAL THE BASE COVER, REPEAT THE STEPS ABOVE IN
3. TO REINSTAL THE BASE COVER, REPEAT THE STEPS ABOVE IN
REVERSE ORDER.
REVERSE ORDER.
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
NOTE: CHECK TO INSURE THAT THE WIRES ARE NOT PINCHED
AGAINST THE CASTING OR HOOD DURING RE-INSTALLATION OF
AGAINST THE CASTING OR HOOD DURING RE-INSTALLATION OF
THE REFLECTOR PLATE ASSEMBLY OR UL COVER.
THE REFLECTOR PLATE ASSEMBLY OR UL COVER.
PLATE REMOVAL & INSTALLATION:
PLATE REMOVAL & INSTALLATION:
1.
TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
TO OPEN THE FIXTURE, LOCATE THE TWO CLOSURE SCREWS.
THESE ARE LOCATED ON THE TWO ROUND BOSSES ON THE
THESE ARE LOCATED ON THE TWO ROUND BOSSES ON THE
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
STREET SIDE OF THE FIXTURE. (SEE FIGURE 1.)
2. UNSCREW THE TWO
2. UNSCREW THE TWO
CAPTIVE
CAPTIVE
CLOSURE SCREWS. YOU WILL
CLOSURE SCREWS. YOU WILL
KNOW
KNOW
T
T
HE SCREWS ARE COMPLETELY DISENGAGED FROM
HE SCREWS ARE COMPLETELY DISENGAGED FROM
THE HOOD
THE HOOD
WHEN
WHEN
THE SCREWS CAN MOVE FREELY UP AND
THE SCREWS CAN MOVE FREELY UP AND
DOWN.
DOWN.
3. OPEN THE HOOD.
3. OPEN THE HOOD.
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE-
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE-
TIGHTEN
TIGHTEN
THE TWO CA
THE TWO CAP
TIVE CLOSURE SCREWS.
TIVE CLOSURE SCREWS.
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT
SIMPLY PULL
SIMPLY PULL
BOTH TRIGGERS SIMULTANEOUSLY WITH YOU
BOTH TRIGGERS SIMULTANEOUSLY WITH YOU
INDEX FINGER WHILE
INDEX FINGER WHILE
PUSHING UP ON THE HOOD WITH YOUR
PUSHING UP ON THE HOOD WITH YOUR
THUMBS. CLOSE THE UNIT BY
THUMBS. CLOSE THE UNIT BY
CLOSING THE HOOD AND PRESSING
CLOSING THE HOOD AND PRESSING
DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
DOWN UNTIL THE TRIGGER LATCHES ENGAGE.
CAUTION
!
LIFT UNIT OUT OF BOX BY BAG, NOT CUPOLA
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
WARNING
!
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
CONSULT LOCAL CODE AUTHORITY
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
WARNING
CAUTION
!
!
CUPOLA CAP
CUPOLA CAP
CUPOLA BASE
CUPOLA BASE
CLOSURE
CLOSURE
SCREW
SCREW
BOSS (2)
BOSS (2)
SCREW NOT
SCREW NOT
SHOWN
SHOWN
LOWER HOUSING
LOWER HOUSING
MIN POLE OD 2.375”
MIN POLE OD 2.375”
MAX POLE OD 3”
MAX POLE OD 3”
SET SCREWS (3)
SET SCREWS (3)
LADDER REST (2)
LADDER REST (2)
-OPTIONAL-
-OPTIONAL-
LENS
LENS
PANELS (4)
PANELS (4)
TRIGGER
TRIGGER
LATCH (2)
LATCH (2)
-OPTIONAL-
-OPTIONAL-
CUPOLA LENS
CUPOLA LENS
ADJUST PHOTOCONTROL
ADJUST PHOTOCONTROL
BY LIFTING & TURNING
BY LIFTING & TURNING
CUPOLA SIMULTANEOUSLY
CUPOLA SIMULTANEOUSLY
FIGURE 1
FIGURE 1
CLOSED HOOD - STREET SIDE VIEW
CLOSED HOOD - STREET SIDE VIEW
HOOD
HOOD
FIGURE 2
FIGURE 2
HOOD ASSEMBLY
HOOD ASSEMBLY
TM
HOOD
HOOD
REFLECTOR
REFLECTOR
PLATE
PLATE
SCREWS
SCREWS
TETHER
TETHER
SCREW
SCREW
(UL VERSION) COVER REMOVAL & INSTALLATION:
(UL VERSION) COVER REMOVAL & INSTALLATION:
American Electric Lighting a division of Acuity Lighting Group, Inc. Granville, OH
DRAWING NO. A68128 REV A (BACK)
©2011 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-71-68128
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
VALIANT SERIES POST TOP LED VERSION cont.
VALIANT SERIES POST TOP LED VERSION cont.
MOUNTING:
MOUNTING:
NOTE: THIS UNIT WILL ACCEPT POLE TOPS WITH AN
NOTE: THIS UNIT WILL ACCEPT POLE TOPS WITH AN
EXTERIOR DIAMETER BETWEEN 2.375” AND 3“
EXTERIOR DIAMETER BETWEEN 2.375” AND 3“
1. WHEN PLACING THE UNIT ON THE POLE, FEED THE
1. WHEN PLACING THE UNIT ON THE POLE, FEED THE
SUPPLY LEADS THROUGH THE BASE OF THE UNIT.
SUPPLY LEADS THROUGH THE BASE OF THE UNIT.
NOTE: IF UNIT IS PRE-WIRED, INSTEAD OF STEP 1, FEED
NOTE: IF UNIT IS PRE-WIRED, INSTEAD OF STEP 1, FEED
THE SUPPLIED PRE-WIRE THROUGH THE POST TOP AND
THE SUPPLIED PRE-WIRE THROUGH THE POST TOP AND
DOWN THE POLE.
DOWN THE POLE.
3. ORIENT THE UNIT SO THE CLOSURE SCREWS (OR
3. ORIENT THE UNIT SO THE CLOSURE SCREWS (OR
TRIGGER LATCHES IF EQUIPPED) ARE TO THE
TRIGGER LATCHES IF EQUIPPED) ARE TO THE
STREET SIDE.
STREET SIDE.
4. TIGHTEN THE THREE MOUNTING SET SCREWS.
4. TIGHTEN THE THREE MOUNTING SET SCREWS.
WIRING:
WIRING:
N
OTE: THIS PROCEDURE IS NOT NECESSARY IF UNIT IS
OTE: THIS PROCEDURE IS NOT NECESSARY IF UNIT IS
SUPPLIED WITH PRE-WIRE.
SUPPLIED WITH PRE-WIRE.
1. OPEN THE HOOD. (SEE “OPENING AND CLOSING THE
1. OPEN THE HOOD. (SEE “OPENING AND CLOSING THE
UNIT” SECTION.)
UNIT” SECTION.)
2. LOCATE THE WIRING DIAGRAM ATTACHED TO THE
2. LOCATE THE WIRING DIAGRAM ATTACHED TO THE
INSIDE OF THE BASE.
INSIDE OF THE BASE.
3. USING THE WIRING DIAGRAM AS A GUIDE, CONNECT
3. USING THE WIRING DIAGRAM AS A GUIDE, CONNECT
THE POWER SUPPLY LEADS TO THE TERMINAL BLOCK.
THE POWER SUPPLY LEADS TO THE TERMINAL BLOCK.
4. CONNECT THE GREEN OR BARE GROUND SUPPLY WIRE
4. CONNECT THE GREEN OR BARE GROUND SUPPLY WIRE
TO THE CASTING BY HOOKING IT AROUND THE HEAD OF
TO THE CASTING BY HOOKING IT AROUND THE HEAD OF
THE GREEN GROUNDING SCREW, LOCATED BESIDE THE
THE GREEN GROUNDING SCREW, LOCATED BESIDE THE
TERMINAL BLOCK, AND TIGHTENING THE SCREW
TERMINAL BLOCK, AND TIGHTENING THE SCREW
SECURELY.
SECURELY.
5. CLOSE THE UNIT.
5. CLOSE THE UNIT.
- IF NO PHOTOCONTROL OPTION WAS SELECTED, A CUSTOMER
- IF NO PHOTOCONTROL OPTION WAS SELECTED, A CUSTOMER
SUPPLIED PHOTOCONTROL WILL NEED TO BE INSTALLED. SEE
SUPPLIED PHOTOCONTROL WILL NEED TO BE INSTALLED. SEE
STEP 1 BELOW.
STEP 1 BELOW.
- IF “PC” WAS SPECIFIED WHEN ORDERING, THE UNIT WILL COME
- IF “PC” WAS SPECIFIED WHEN ORDERING, THE UNIT WILL COME
WITH THE PHOTOCONTROL INSTALLED. SEE STEP 4 BELOW.
WITH THE PHOTOCONTROL INSTALLED. SEE STEP 4 BELOW.
- IF “NR” WAS SPECIFIED, THE UNIT COMES STANDARD WITH A
- IF “NR” WAS SPECIFIED, THE UNIT COMES STANDARD WITH A
SHORTING CAP AND THE STEPS BELOW ARE NOT NECESSARY.
SHORTING CAP AND THE STEPS BELOW ARE NOT NECESSARY.
1. REMOVE THE CUPOLA CAP BY GRABBING ONE SIDE OF IT AND
1. REMOVE THE CUPOLA CAP BY GRABBING ONE SIDE OF IT AND
LIFTING UP. (SEE FIGURE 1) THE CUPOLA CAP IS VERY RIGID
LIFTING UP. (SEE FIGURE 1) THE CUPOLA CAP IS VERY RIGID
AND TIGHT, DESIGNED SO IT DOESN’T EASILY COME OFF.
AND TIGHT, DESIGNED SO IT DOESN’T EASILY COME OFF.
HOWEVER, IT MAY BE REMOVED BY HAND.
HOWEVER, IT MAY BE REMOVED BY HAND.
2. INSERT THE PHOTOCONTROL INTO THE RECEPTACLE.
2. INSERT THE PHOTOCONTROL INTO THE RECEPTACLE.
3. REATTACH THE CUPOLA CAP. IT SHOULD REATTACH WITH A
3. REATTACH THE CUPOLA CAP. IT SHOULD REATTACH WITH A
VERY AUDIBLE SNAP.
VERY AUDIBLE SNAP.
4. TURN THE PHOTOCONTROL WINDOW TOWARD NORTH BY
4. TURN THE PHOTOCONTROL WINDOW TOWARD NORTH BY
GRABBING THE CUPOLA BASE WITH BOTH HANDS, LIFTING AND
GRABBING THE CUPOLA BASE WITH BOTH HANDS, LIFTING AND
TURNING SIMULTANEOUSLY UNTIL THE CUPOLA WINDOW IS
TURNING SIMULTANEOUSLY UNTIL THE CUPOLA WINDOW IS
FACING NORTH. THE CUPOLA BASE AND THE PHOTOCONTROL
FACING NORTH. THE CUPOLA BASE AND THE PHOTOCONTROL
RECEPTACLE ARE KEYED SO THE PHOTOCONTROL TURNS AS
RECEPTACLE ARE KEYED SO THE PHOTOCONTROL TURNS AS
THE CUPOLA DOES.
THE CUPOLA DOES.
NOTE: FOR ELECTRICAL SAFETY PURPOSES, THE CUPOLA IS
NOTE: FOR ELECTRICAL SAFETY PURPOSES, THE CUPOLA IS
DESIGNED SO THAT IT WILL NOT TURN BEYOND 360 DEGREES.
DESIGNED SO THAT IT WILL NOT TURN BEYOND 360 DEGREES.
DEPENDING ON THE INITIAL ORIENTATION, IT MAY BE NECESS-
DEPENDING ON THE INITIAL ORIENTATION, IT MAY BE NECESS-
ARY TO TURN THE CUPOLA IN THE OTHER DIRECTION IF IT
ARY TO TURN THE CUPOLA IN THE OTHER DIRECTION IF IT
STOPS AND REFUSES TO TURN.
STOPS AND REFUSES TO TURN.
L
ADDER REST INSTALLATION:
ADDER REST INSTALLATION:
NOTE: IT IS DESIGNED TO BREAK-AWAY UNDER SIDE FORCE.
NOTE: IT IS DESIGNED TO BREAK-AWAY UNDER SIDE FORCE.
HOWEVER, IT CAN BE REATTACHED WITH A 1/4-20X3/4 BOLT
HOWEVER, IT CAN BE REATTACHED WITH A 1/4-20X3/4 BOLT
AND NUT AVAILABLE IN THE LADDER REST REPLACEMENT KIT
AND NUT AVAILABLE IN THE LADDER REST REPLACEMENT KIT
(THE KIT ALSO CONTAINS TWO ADDITIONAL LADDER RESTS.)
(THE KIT ALSO CONTAINS TWO ADDITIONAL LADDER RESTS.)
NOTE: THE LADDER REST IS A PRESS FIT DESIGN INTENDED
NOTE: THE LADDER REST IS A PRESS FIT DESIGN INTENDED
FOR INSTALLATION AFTER THE UNIT IS INSTALLED ONTO THE
FOR INSTALLATION AFTER THE UNIT IS INSTALLED ONTO THE
POST TOP.
POST TOP.
1. INSERT THE PIN FEATURE ON THE LADDER REST (SEE
1. INSERT THE PIN FEATURE ON THE LADDER REST (SEE
FIGURE 3) INTO THE LADDER REST HOLE LOCATED ON
FIGURE 3) INTO THE LADDER REST HOLE LOCATED ON
THE LEFT AND RIGHT SIDE OF THE LOWER HOUSING JUST
THE LEFT AND RIGHT SIDE OF THE LOWER HOUSING JUST
ABOVE THE MOUNT SET SCREWS.
ABOVE THE MOUNT SET SCREWS.
2. USING A RUBBER MALLET OR HAMMER, GENTLY KNOCK
2. USING A RUBBER MALLET OR HAMMER, GENTLY KNOCK
THE LADDER REST INTO THE HOLE. BE SURE TO KEEP
THE LADDER REST INTO THE HOLE. BE SURE TO KEEP
THE LADDER REST LINED UP WITH THE HOLE SO THAT
THE LADDER REST LINED UP WITH THE HOLE SO THAT
THERE SI NO DAMAGE TO THE PIN.
THERE SI NO DAMAGE TO THE PIN.
NOTES: IF THE PIN IS DAMAGED BEYOND REPAIR, REMOVE
NOTES: IF THE PIN IS DAMAGED BEYOND REPAIR, REMOVE
IT WITH PLIERS AND REATTACH USING A 1/4-20X3/4 BOLT
IT WITH PLIERS AND REATTACH USING A 1/4-20X3/4 BOLT
AND NUT.
AND NUT.
CAUTION
DO NOT TIGHTEN SET SCREWS
BEYOND 15 ft-lb. TORQUE.
!
CAUTION
THE LADDER REST IS FOR
COSMETIC PURPOSES ONLY. IT
IS NOT INTENDED FOR USE AS
AN ACTUAL REST FOR A LADDER.
!
PHOTOCONTROL:
PHOTOCONTROL:
NOTE: ON THE AVP, NO TOOLING IS NECESSARY FOR THE
NOTE: ON THE AVP, NO TOOLING IS NECESSARY FOR THE
PHOTOCONTROL INSTALLATION OR ADJUSTMENT.
PHOTOCONTROL INSTALLATION OR ADJUSTMENT.
FIGURE 3
FIGURE 3
LADDER REST INSTALLATION
LADDER REST INSTALLATION
PIN
PIN
GENTLY KNOCK HERE
GENTLY KNOCK HERE
FOR INSTALLATION.
FOR INSTALLATION.
TM
/
