INSTALLATION INSTRUCTIONS
AMERICAN REVOLUTION POST TOP 247 LED SERIES
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
DRAWING NO. A72881 REV A (FRONT)
©2013 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-72881
OPENING & CLOSING THE UNIT:
OPENING & CLOSING THE UNIT:
1.
TO OPEN THE FIXTURE, LOCATE THE CLOSURE SCREW.
TO OPEN THE FIXTURE, LOCATE THE CLOSURE SCREW.
IT IS LOCATED ON THE STREET SIDE OF THE FIXTURE.
IT IS LOCATED ON THE STREET SIDE OF THE FIXTURE.
(SEE FIGURE 1.)
(SEE FIGURE 1.)
2. UNSCREW THE IS CAPTIVE CLOSURE SCREW. YOU WILL
2. UNSCREW THE IS CAPTIVE CLOSURE SCREW. YOU WILL
KNOW
KNOW
T
T
HE SCREW
HE SCREW
IS
IS
COMPLETELY DISENGAGED FROM
COMPLETELY DISENGAGED FROM
THE HOOD
THE HOOD
WHEN
WHEN
THE SCREW CAN MOVE FREELY UP AND
THE SCREW CAN MOVE FREELY UP AND
DOWN.
DOWN.
3. OPEN THE HOOD.
3. OPEN THE HOOD.
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE
HOOD AND RE-
HOOD AND RE-
TIGHTEN THE CAPTIVE CLOSURE SCREW.
TIGHTEN THE CAPTIVE CLOSURE SCREW.
NOTE FOR OPTIONAL
NOTE FOR OPTIONAL
TRIGGER LATCH: TO OPEN THE UNIT
TRIGGER LATCH: TO OPEN THE UNIT
SIMPLY PULL
SIMPLY PULL
TRIGGER WITH YOU
TRIGGER WITH YOUR
INDEX FINGER WHILE
INDEX FINGER WHILE
PUSHING UP ON THE HOOD WITH YOUR
PUSHING UP ON THE HOOD WITH YOUR
THUMBS. CLOSE
THUMBS. CLOSE
THE UNIT BY
THE UNIT BY
CLOSING THE HOOD AND PRESSING
CLOSING THE HOOD AND PRESSING
DOWN
DOWN
UNTIL THE TRIGGER
UNTIL THE TRIGGER
LATCH
LATCH
ENGAGE.
ENGAGE.
CAUTION
!
LIFT UNIT OUT OF BOX BY BAG, NOT CUPOLA
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
WARNING
!
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
CONSULT LOCAL CODE AUTHORITY
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
WARNING
CAUTION
!
!
FIGURE 1
FIGURE 1
CLOSED HOOD - STREET SIDE VIEW
CLOSED HOOD - STREET SIDE VIEW
FIGURE 2
FIGURE 2
OPEN HOOD - TOP VIEW
OPEN HOOD - TOP VIEW
TM
CUPOLA CAP
CUPOLA CAP
CUPOLA BASE
CUPOLA BASE
SET SCREWS (3)
SET SCREWS (3)
LADDER REST (2)
LADDER REST (2)
-OPTIONAL-
-OPTIONAL-
NEMA
NEMA
LABEL HERE
LABEL HERE
-OPTIONAL-
-OPTIONAL-
LENS
LENS
PANELS (4)
PANELS (4)
TRIGGER
TRIGGER
LATCH
LATCH
-OPTIONAL-
-OPTIONAL-
CUPOLA LENS
CUPOLA LENS
ADJUST PHOTO-
ADJUST PHOTO-
CONTROL BY LIFTING
CONTROL BY LIFTING
& TURNING CUPOLA
& TURNING CUPOLA
SIMULTANEOUSLY
SIMULTANEOUSLY
HOOD
HOOD
CLOSURE
CLOSURE
SCREW
SCREW
BOSS
BOSS
SCREW NOT
SCREW NOT
SHOWN
SHOWN
LOWER HOUSING
LOWER HOUSING
MIN POLE OD 2.375”
MIN POLE OD 2.375”
MAX POLE OD 3”
MAX POLE OD 3”
LENS
LENS
PANELS (4)
PANELS (4)
LOWER
LOWER
HOUSING
HOUSING
WIRING:
WIRING:
1. OPEN THE UNIT AND REMOVE THE STREET SIDE LENS. (SEE
1. OPEN THE UNIT AND REMOVE THE STREET SIDE LENS. (SEE
FIGURE 2).
FIGURE 2).
2. LOCATE THE WIRING DIAGRAM ATTACHED TO THE
2. LOCATE THE WIRING DIAGRAM ATTACHED TO THE
INSIDE OF THE HOOD.
INSIDE OF THE HOOD.
3. PULL UP THE TERMINAL BLOCK COVER.
3. PULL UP THE TERMINAL BLOCK COVER.
4. USING THE WIRING DIAGRAM AS A GUIDE, CONNECT
4. USING THE WIRING DIAGRAM AS A GUIDE, CONNECT
THE POWER SUPPLY LEADS TO TEH TERMINAL BLOCK. (SEE
THE POWER SUPPLY LEADS TO TEH TERMINAL BLOCK. (SEE
FIGURE 2).
FIGURE 2).
5. CONNECT THE GREEN OR BARE GROUND SUPPLY WIRE
5. CONNECT THE GREEN OR BARE GROUND SUPPLY WIRE
TO THE CASTING BY HOOKING IT AROUND THE HEAD OF
TO THE CASTING BY HOOKING IT AROUND THE HEAD OF
THE GREEN GROUNDING SCREW, LOCATED BESIDE THE
THE GREEN GROUNDING SCREW, LOCATED BESIDE THE
TERMINAL BLOCK, AND TIGHTENING THE SCREW
TERMINAL BLOCK, AND TIGHTENING THE SCREW
SECURELY.
SECURELY.
6. PUSH DOWN THE TERMINAL BLOCK COVER.
6. PUSH DOWN THE TERMINAL BLOCK COVER.
5. REINSTALL THE STREET SIDE LENS.
5. REINSTALL THE STREET SIDE LENS.
6. CLOSE THE UNIT.
6. CLOSE THE UNIT.
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
DRAWING NO. A72881 REV A (BACK)
©2013 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-72881
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
AMERICAN REVOLUTION POST TOP 247 LED SERIES
AMERICAN REVOLUTION POST TOP 247 LED SERIES
cont.
cont.
MOUNTING:
MOUNTING:
NOTE: THIS UNIT WILL ACCEPT POLE TOPS WITH AN
NOTE: THIS UNIT WILL ACCEPT POLE TOPS WITH AN
EXTERIOR DIAMETER BETWEEN 2.375” AND 3“
EXTERIOR DIAMETER BETWEEN 2.375” AND 3“
1. WHEN PLACING THE UNIT ON THE POLE, FEED THE
1. WHEN PLACING THE UNIT ON THE POLE, FEED THE
SUPPLY LEADS THROUGH THE BASE OF THE UNIT.
SUPPLY LEADS THROUGH THE BASE OF THE UNIT.
2. ORIENT THE UNIT SO THAT THE CLOSURE SCREW
2. ORIENT THE UNIT SO THAT THE CLOSURE SCREW
(OR TRIGGER LATCH IF EQUIPPED) ARE TO THE
(OR TRIGGER LATCH IF EQUIPPED) ARE TO THE
STREET SIDE.
STREET SIDE.
3. TIGHTEN THE THREE MOUNTING SET SCREWS.
3. TIGHTEN THE THREE MOUNTING SET SCREWS.
NOTE: FOR ELECTRICAL SAFETY PURPOSES, THE CUPOLA IS
NOTE: FOR ELECTRICAL SAFETY PURPOSES, THE CUPOLA IS
DESIGNED SO THAT IT WILL NOT TURN BEYOND 360 DEGREES.
DESIGNED SO THAT IT WILL NOT TURN BEYOND 360 DEGREES.
DEPENDING ON THE INITIAL ORIENTATION, IT MAY BE NECESS-
DEPENDING ON THE INITIAL ORIENTATION, IT MAY BE NECESS-
ARY TO TURN THE CUPOLA IN THE OTHER DIRECTION IF IT
ARY TO TURN THE CUPOLA IN THE OTHER DIRECTION IF IT
STOPS AND REFUSES TO TURN.
STOPS AND REFUSES TO TURN.
L
ADDER REST INSTALLATION CONT:
ADDER REST INSTALLATION CONT:
CAUTION
DO NOT TIGHTEN SET SCREWS
BEYOND 15 ft-lb. TORQUE.
!
PHOTOCONTROL:
PHOTOCONTROL:
NOTE: NO TOOLING IS NECESSARY FOR THE PHOTO-
NOTE: NO TOOLING IS NECESSARY FOR THE PHOTO-
CONTROL INSTALLATION OR ADJUSTMENT.
CONTROL INSTALLATION OR ADJUSTMENT.
- IF NO PHOTOCONTROL OPTION WAS SELECTED, A
- IF NO PHOTOCONTROL OPTION WAS SELECTED, A
CUSTOMER SUPPLIED PHOTOCONTROL WILL NEED
CUSTOMER SUPPLIED PHOTOCONTROL WILL NEED
TO BE INSTALLED. SEE STEP 1 BELOW.
TO BE INSTALLED. SEE STEP 1 BELOW.
- IF “NR” WAS SPECIFIED, THE STEPS BELOW ARE NOT
- IF “NR” WAS SPECIFIED, THE STEPS BELOW ARE NOT
NECESSARY.
NECESSARY.
1. REMOVE THE CUPOLA CAP BY GRABBING ONE SIDE OF
1. REMOVE THE CUPOLA CAP BY GRABBING ONE SIDE OF
IT AND LIFTING UP. (SEE FIGURE 1) THE CUPOLA CAP IS
IT AND LIFTING UP. (SEE FIGURE 1) THE CUPOLA CAP IS
VERY RIGID AND TIGHT, DESIGNED SO IT DOESN’T EASILY
VERY RIGID AND TIGHT, DESIGNED SO IT DOESN’T EASILY
COME OFF. HOWEVER, IT MAY BE REMOVED BY HAND.
COME OFF. HOWEVER, IT MAY BE REMOVED BY HAND.
2. INSERT THE PHOTOCONTROL INTO THE RECEPTACLE.
2. INSERT THE PHOTOCONTROL INTO THE RECEPTACLE.
3. REATTACH THE CUPOLA CAP. IT SHOULD REATTACH WITH
3. REATTACH THE CUPOLA CAP. IT SHOULD REATTACH WITH
A VERY AUDIBLE SNAP.
A VERY AUDIBLE SNAP.
4. TURN THE PHOTOCONTROL WINDOW TOWARD NORTH BY
4. TURN THE PHOTOCONTROL WINDOW TOWARD NORTH BY
GRABBING THE CUPOLA BASE WITH BOTH HANDS, LIFTING
GRABBING THE CUPOLA BASE WITH BOTH HANDS, LIFTING
AND TURNING SIMULTANEOUSLY UNTIL THE CUPOLA
AND TURNING SIMULTANEOUSLY UNTIL THE CUPOLA
WINDOW IS FACING NORTH. THE CUPOLA BASE AND THE
WINDOW IS FACING NORTH. THE CUPOLA BASE AND THE
PHOTOCONTROL RECEPTACLE ARE KEYED SO THE
PHOTOCONTROL RECEPTACLE ARE KEYED SO THE
PHOTOCONTROL TURNS AS THE CUPOLA DOES.
PHOTOCONTROL TURNS AS THE CUPOLA DOES.
FIGURE 3
FIGURE 3
LADDER REST INSTALLATION
LADDER REST INSTALLATION
PIN
PIN
GENTLY KNOCK HERE
GENTLY KNOCK HERE
FOR INSTALLATION.
FOR INSTALLATION.
TM
THIS DEVICE COMPLIES WITH PART 18 THE FCC RULES BUT MAY
THIS DEVICE COMPLIES WITH PART 18 THE FCC RULES BUT MAY
CAUSE INTERFERENCE WITH CORDLESS AND CELL PHONE,
CAUSE INTERFERENCE WITH CORDLESS AND CELL PHONE,
RADIOS, TELEVISIONS AND OTHER ELECTRICAL DEVICES.
RADIOS, TELEVISIONS AND OTHER ELECTRICAL DEVICES.
TO CORRECT THE PROBLEM MOVE THE DEVICE AWAT FROM THE
TO CORRECT THE PROBLEM MOVE THE DEVICE AWAT FROM THE
LUMINARY OR PLUG INTO A DIFFERENT OUTLET.
LUMINARY OR PLUG INTO A DIFFERENT OUTLET.
THIS PRODUCT MAY CAUSE INTERFERENCE TO RADIO EQUIPMENT
THIS PRODUCT MAY CAUSE INTERFERENCE TO RADIO EQUIPMENT
AND SHOULD NOT BE INSTALLED NEAR MARITIME SAFETY
AND SHOULD NOT BE INSTALLED NEAR MARITIME SAFETY
COMMUNICATIONS EQUIPMENT OR OTHER CRITICAL NAVIGATION
COMMUNICATIONS EQUIPMENT OR OTHER CRITICAL NAVIGATION
OR COMMUNICATION EQUIPMENT OPERATING BETWEEN
OR COMMUNICATION EQUIPMENT OPERATING BETWEEN
0.45-30 MHz.
0.45-30 MHz.
NOTE:
NOTE:
1. INSERT THE ROAM NODE INTO THE RECEPTACLE. (ROAM
1. INSERT THE ROAM NODE INTO THE RECEPTACLE. (ROAM
NODE ORDERED SEPARATELY).
NODE ORDERED SEPARATELY).
2. INSERT THE CUPOLA LENS (SEE FIGURE 4) (CUPOLA
2. INSERT THE CUPOLA LENS (SEE FIGURE 4) (CUPOLA
LENS CAME INSIDE THE FIXTURE).
LENS CAME INSIDE THE FIXTURE).
3. ATTACH THE CUPOLA CAP (SEE FIGURE 4). IT SHOULD
3. ATTACH THE CUPOLA CAP (SEE FIGURE 4). IT SHOULD
ATTACH WITH A VERY AUDIBLE SNAP. (CUPOLA CAP CAME
ATTACH WITH A VERY AUDIBLE SNAP. (CUPOLA CAP CAME
INSIDE THE FIXTURE).
INSIDE THE FIXTURE).
4. TURN THE ROAM NODE WINDOW TOWARD NORTH BY
4. TURN THE ROAM NODE WINDOW TOWARD NORTH BY
GRABBING THE CUPOLA BASE WITH BOTH HANDS, LIFTING
GRABBING THE CUPOLA BASE WITH BOTH HANDS, LIFTING
AND TURNING SIMULTANEOUSLY UNTIL THE CUPOLA
AND TURNING SIMULTANEOUSLY UNTIL THE CUPOLA
WINDOW IS FACING NORTH. THE CUPOLA BASE AND
WINDOW IS FACING NORTH. THE CUPOLA BASE AND
THE PHOTOCONTROL RECEPTACLE ARE KEYED SO THE
THE PHOTOCONTROL RECEPTACLE ARE KEYED SO THE
ROAM NODE TURNS AS THE CUPOLA DOES.
ROAM NODE TURNS AS THE CUPOLA DOES.
NOTE: FOR ELECTRICAL SAFETY PURPOSES, THE CUPOLA IS
NOTE: FOR ELECTRICAL SAFETY PURPOSES, THE CUPOLA IS
DESIGNED SO THAT IT WILL NOT TURN BEYOND 360 DEGREES.
DESIGNED SO THAT IT WILL NOT TURN BEYOND 360 DEGREES.
DEPENDING ON THE INITIAL ORIENTATION, IT MAY BE NECESS-
DEPENDING ON THE INITIAL ORIENTATION, IT MAY BE NECESS-
ARY TO TURN THE CUPOLA IN THE OTHER DIRECTION IF IT
ARY TO TURN THE CUPOLA IN THE OTHER DIRECTION IF IT
STOPS AND REFUSES TO TURN.
STOPS AND REFUSES TO TURN.
ROAM CONCIERGE/VIEW (DE OR VE OPTIONS):
ROAM CONCIERGE/VIEW (DE OR VE OPTIONS):
L
ADDER REST INSTALLATION:
ADDER REST INSTALLATION:
NOTE: IT IS DESIGNED TO BREAK-AWAY UNDER SIDE FORCE.
NOTE: IT IS DESIGNED TO BREAK-AWAY UNDER SIDE FORCE.
HOWEVER, IT CAN BE REATTACHED WITH A 1/4-20X3/4 BOLT
HOWEVER, IT CAN BE REATTACHED WITH A 1/4-20X3/4 BOLT
AND NUT AVAILABLE IN THE LADDER REST REPLACEMENT KIT
AND NUT AVAILABLE IN THE LADDER REST REPLACEMENT KIT
(THE KIT ALSO CONTAINS TWO ADDITIONAL LADDER RESTS.)
(THE KIT ALSO CONTAINS TWO ADDITIONAL LADDER RESTS.)
NOTE: THE LADDER REST IS A PRESS FIT DESIGN INTENDED
NOTE: THE LADDER REST IS A PRESS FIT DESIGN INTENDED
FOR INSTALLATION AFTER THE UNIT IS INSTALLED ONTO THE
FOR INSTALLATION AFTER THE UNIT IS INSTALLED ONTO THE
POST TOP.
POST TOP.
1. INSERT THE PIN FEATURE ON THE LADDER REST (SEE
1. INSERT THE PIN FEATURE ON THE LADDER REST (SEE
FIGURE 3) INTO THE LADDER REST HOLE LOCATED ON THE
FIGURE 3) INTO THE LADDER REST HOLE LOCATED ON THE
LEFT AND RIGHT SIDE OF THE LOWER HOUSING JUST ABOVE
LEFT AND RIGHT SIDE OF THE LOWER HOUSING JUST ABOVE
THE MOUNT SET SCREWS.
THE MOUNT SET SCREWS.
2. USING A RUBBER MALLET OR HAMMER, GENTLY KNOCK THE
2. USING A RUBBER MALLET OR HAMMER, GENTLY KNOCK THE
LADDER REST INTO THE HOLE. BE SURE TO KEEP THE
LADDER REST INTO THE HOLE. BE SURE TO KEEP THE
LADDER REST LINED UP WITH THE HOLE SO THAT THERE IS
LADDER REST LINED UP WITH THE HOLE SO THAT THERE IS
NO DAMAGE TO THE PIN.
NO DAMAGE TO THE PIN.
NOTES: IF THE PIN IS DAMAGED BEYOND REPAIR, REMOVE
NOTES: IF THE PIN IS DAMAGED BEYOND REPAIR, REMOVE
IT WITH PLIERS AND REATTACH USING A 1/4-20X3/4 BOLT
IT WITH PLIERS AND REATTACH USING A 1/4-20X3/4 BOLT
AND NUT.
AND NUT.
FIGURE 4
FIGURE 4
CUPOLA WINDOW AND CAP INSTALLATION
CUPOLA WINDOW AND CAP INSTALLATION
CUPOLA CAP
CUPOLA CAP
CUPOLA WINDOW
CUPOLA WINDOW
CUPOLA
CUPOLA
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
INSTALLATION INSTRUCTIONS
AMERICAN REVOLUTION
TM
POST TOP 247 LED SERIES cont.
Field Adjustable Output Module
THE FIELD ADJUSTABLE OUTPUT (AO) MODULE IS AN ONBOARD
DEVICE THAT ADJUSTS THE LIGHT OUTPUT AND INPUT WATTAGE
TO MEET SITE SPECIFIC REQUIREMENTS, ALLOWING A SINGLE FIXTURE
CONFIGURATION TO BE FLEXIBLY APPLIED IN MANY DIFFERENT
APPLICATION.THE AO OPTION IS AVAILABLE ON THE 247 SERIES
THE FOLLOWONG DATA IS FOR AS VOLTAGE OPTIONS
DRAWING NO. A72881 REV B (BACK)
©2013 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-72881
P10, P15, P20 - AS ONLY
AO Position
%
Lumens
% Wattage
8
100%
100%
7
90%
90%
6
80%
80%
5
65%
65%
4
50%
50%
3
35%
35%
2
20%
20%
1
10%
10%
P35, P40, P45 - AS ONLY
AO Position
%
Lumens
% Wattage
8
100%
100%
7
90%
90%
6
80%
80%
5
65%
65%
4
55%
55%
3
40%
40%
2
30%
30%
1
15%
15%
P25, P30 - AS ONLY
AO Position
%
Lumens
% Wattage
8
100%
100%
7
90%
95%
6
80%
80%
5
65%
65%
4
50%
55%
3
35%
40%
2
20%
30%
1
10%
15%
P50, P55 - AS ONLY
AO Position
%
Lumens
% Wattage
8
100%
100%
7
90%
95%
6
80%
80%
5
65%
65%
4
50%
50%
3
35%
40%
2
20%
30%
1
10%
15%
REV
DATE
DESCRIPTION
ECN
BY
APP
--
06-JUN-2013
NEW RELEASE
017-3249
ALG
MEJ
A
15-NOV-2013
WARRANTY NOTE WAS REMOVED. ROAM NODE OPTION WAS ADDED.
017-3393
ALG
MEJ
B
09-MAY-2019
ADDED FAO TABLE.
017-7380
AXM
CTB
PART NUMBER.
057-70-72881
DESCRIPTION
INSTALLATION INSTRUCTIONS
AMERICAN REVOLUTION
TM
POST TOP
247 LED SERIES
DWG NUMBER
A72881
SHT 4 OF 4
/
