Whirlpool WVES 23932 W Program Chart

Brand: Whirlpool

Model: WVES 23932 W

Type: Program Chart

This manual is also suitable for

ROPLLVLTHUEECZBGGB UARU SK

1. Control panel

2. Ice packs (inside - if proved for)

3. Rating plate (at side of drawer)

4. Freezing compartment

5. Zone for drawers and pull-out baskets

Storage zone

Freezing zone

Note: The design of drawers and

accessories may vary, depending

on the model.

PRODUCT SHEET

A. 6th Sense. “6th Sense” activation indicator

(see enclosed instructions).

B. On/Standby. Standby button. Press for at

least 3 seconds to activate it. Press the icon

once to reactivate the keypad.

C. Temperature. Set temperature indicator.

D. Temperature. Temperature setting button.

E. Key Lock. Key Lock activated indicator.

Press for 3 seconds to activate/deactivate

the Key Lock. When activated, pressing the

other icons activates an audible signal.

F. Stop alarm. Press in case of alarm.

G. Black-out alarm. Long Black-out Alarm

indicator.(See the section “alarm signaling”.)

H. Fast Freeze. Fast Freeze on indicator.

Press to activate/deactivate the Fast Freeze

function. The Fast Freeze function switches

off automatically after 48 hours.

CONTROL PANEL

ROPLLVLTHUEECZBGGB UARU SK

Freezer inside temperature adjustment

The appliance is normally factory-set for operation at the recommended temperature of -18°C.

C. The inside temperature setting can be adjusted between -16°C and -24°C, proceeding as

follows:

• PresstheinsidetemperatureadjustmentbuttonD.Thestoragetemperaturecanbechanged

by -1°C with each press of the button: the value flashes cyclically between -16°C and -24°C.

• The6thSensefunctionisactivatedautomaticallyincaseofopeningofdoorsandthe

introduction of small amounts of food to be frozen. Its duration is variable and depends on the

product load conditions and the outside temperature. It does not require any intervention by the

user and switches off automatically when normal operating conditions are restored.

This optional function can be used to save energy. To activate the Eco mode, press the buttons

E and H together for 3 seconds until an audible signal sounds. Two seconds after activation

of the Eco mode, the display goes off, except the “6th Sense” icon (and the audible signal is

deactivated, if on). To adjust the temperature or use other functions, it is necessary to activate the

display by pressing any button. After about 15 seconds without performing any action, the display

goes off again and only the “6th Sense” icon remains visible. To deactivate this function, press

the buttons E and H together for 3 seconds until an audible signal sounds. The normal display is

restored. The Eco mode is automatically disabled after a power failure or a fault alarm. Remember

that this function does not disconnect the appliance from the power supply.

ECO MODE

ROPLLVLTHUEECZBGGB UARU SK

5019 300 01151A Printed in Italy 03/12 - Whirlpool

DEFROST

Note:

The temperature alarm may even be activated following prolonged opening of the door or after

fresh food products have been placed in the freezing zone; the temporary increase in temperature

signaled does not affect the perfect preservation of already frozen food.

ALARM SIGNALING

Signal Cause Cure

Door open alarm The audible alarm is

activated.

The door has remained

open for more than

2 minutes

Close the door

Temperature alarm The audible alarm

is activated, the set

temperature flashes

and the red light F

remains on

The inside temperature

is not adequate

Press the button F;

the audible alarm

stops, the set

temperature flashes

and the red light F

remains on until a

temperature < -10°C

is reached.

Long black-out

alarm

The audible alarm is

activated, the light G

remains on, the light F

flashes and the display

shows the maximum

temperature reached.

Prolonged power

failure, able to cause

the inside temperature

to increase to 0°C

Press the button F;

the audible alarm

stops, the set

temperature flashes

and the red light F

remains on until a

temperature < -10°C

is reached.

Malfunction The message “FF”

flashes on the display C

Product malfunction Contact the After-sales

Service

1. Put the product in standby mode by pressing the button B for

at least 3 seconds.

2. Unplug the appliance or turn off the main switch.

3. Insert the chute (contained in the accessories bag) in the

special slot (see figure).

4. Follow the instructions given in the instruction booklet.

5. Reinsert the plug or turn on the main switch.

6. Reactivate the product by pressing the button B once.

Whirlpool WVES 23932 W Program Chart

Brand: Whirlpool

Model: WVES 23932 W

Type: Program Chart

This manual is also suitable for

Download PDF

report

Whirlpool WVES 23932 W Program Chart

This manual is also suitable for

Whirlpool WVES 23932 W Program Chart

Related papers

Other documents