Livoo DOP189N User manual

Category
Small kitchen appliances
Type
User manual

This manual is also suitable for

Instruction manual
WWW.LIVOO.COM
Reference: DOP189
Version: 1.4
Language: English
Stand mixer
Instruction manual
1
You have purchased a product LIVOO brand and we thank you. We take great care in design, ergonomics and ease of
use of our products. We hope that this product will give you complete satisfaction.
This instruction manual is available too on our website www.livoo.fr
General Instructions
PLEASE, TAKE TIME TO READ WELL THE INSTRUCTIONS FOR USE
PARTICULARLY BEFORE THE FIRST USE.
A misuse of the appliance can damage it or hurt the user. Assure that
you use the appliance for the use for which it is designed; we refuse
any responsibilities as for the damages by an incorrect use or a bad
manipulation.
1. Check that your mains voltage corresponds to that stated on
the appliance.
2. The safety instructions do not by themselves eliminate any
danger completely and proper accident prevention
measures must always be used.
3. This appliance shall not be used by children. Keep the
appliance and its cord out of reach of children.
4. Appliances can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and if they
understand the hazards involved.
5. Children shall not play with the appliance.
Instruction manual
2
6. Do not attempt to repair the appliance yourself, since you
will be exposed to hazardous live components or other
hazards by opening and removing the covers.
7. Do not use the appliance outdoor, place it in a dry
environment, and only use the appliance for domestic
purposes and in the way indicated in these instructions.
8. Never leave the appliance unsupervised when in use.
9. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard (*).
10. Place this appliance as close as possible to the power source
so that you can disconnect the plug quickly and easily.
11. Never immerse the base of your appliance in water or any
other liquid for any reason whatsoever. Never place it into
the dishwasher.
12. Always disconnect the appliance from the supply if it is left
unattended and before assembling, disassembling or
cleaning. Do not allow children to use the blender without
supervision.
13. Never move the appliance by pulling the cord. Make sure the
cord cannot get caught in any way. Do not wind the cord
around the appliance and do not bend it.
14. Unplug the appliance when not in use.
15. Avoid contacting with moving parts. Keep hands, clothing, as
well as spatulas and other utensils away from beaters during
Instruction manual
3
operating to reduce the risk of injury to people, and/or
damage to the mixer.
16. The appliance is not intended to be operated by means of
external timer or separate remote control system.
17. Keep this manual with the appliance. If the appliance is to be
used by a third party, this instruction manual must be
supplied with it.
18. To avoid electric shocks, do not use this device in the vicinity
of water. Do not immerse the mains lead in water or other
liquid.
19. Do not kink or clamp the mains lead. To avoid any risk of
stumbling, do not allow the mains lead to hang over the edge
of a table or a counter.
20. This appliance should not be set up in close proximity to a
naked flame, easily flammable materials (curtains, textiles,
etc.), a radiator, an oven or some other heat source.
21. Before use, place the appliance on a horizontal and flat
surface.
22. The appliance should only be used for its intended purpose.
23. During use, do not touch moving parts with your fingers.
24. No liability is accepted for damage due to improper use or
the failure to observe our operating instructions / safety
notes.
25. Be sure to turn the speed selector to 0 position after each
use
.
Instruction manual
4
26.
Switch off the appliance and disconnect from supply before
changing accessories or approaching parts which move in
use.
27.
Never pull out mixing beater/dough hook/egg whisk when
the appliance is in operation.
28.
Be careful if hot liquid is poured into the food processor or
blender as it can be ejected out of the appliance due to a
sudden steaming.
29.
Regarding the instruction for cleaning surfaces in contact
with food or oil thanks to refer to the below paragraph
“cleaning” in manual.
30.
It is absolutely necessary to keep this appliance clean at all
times as it comes into direct contact with food.
31.
There is potential injury from misuse
32.
Regarding the instructions for the use of accessories,
operation times and speed settings, thanks to refer to the
below paragraphs
33.
Accessories, other than those supplied with the appliance,
shall include instructions for their safe use.
34.
Care shall be taken when handling the sharp cutting blades,
emptying the bowl and during cleaning
35.
This appliance is intended to be used in household and
similar applications such as:
staff kitchen areas in shops, offices and other
working environments
Instruction manual
5
farm houses
by clients in hotels, motels and other
residential type environments
bed and breakfast type environments
(*)
Competent qualified electrician: after sales department of the producer or importer or any person who
is qualified, approved and competent to perform this kind of repairs in order to avoid all danger. In any
case you should return the appliance to this electrician.
SPECIFICATIONS
Voltage:
220-240V~ 50-60Hz
Power:
1000W
KB: 15min for mincer and beater function 1cycle/ 10 min for kneader function 1 cycle / 4 min on 1 min off
for blender function 10 cycles
DESCRIPTION
1. Measuring cup
2. Blender lid
3. Blender jar
4. Mixing bowl
5. Bowl cover
6. Head
7. Lever knob
8. Control button
9. Base
10. Kneading hook
11. Mixing blade
12. Egg whisk
13. Cover of blender
Place
14. Grinder place
Instruction manual
6
1.
Sausage funnel
5.
Tagliatelle
disc
9. Medium disc
13
.
Funnel
2.
6.
Thin Spaghetti disc
10. Fine disc
14.
H
opper
plate
3. Sausage adapter
7. Wide Spaghetti disc 11. Blade 15. Pusher
4. Macaroni disc
8. Disc (coarse) 12. Feed screw 16. Cover of grinder place
Instruction manual
7
USING YOUR APPLIANCE
Before first use:
Before assembling or disassembling the appliance, be sure it is unplug and speed selector on OFF position
and put it on stable surface. Clean all accessories, lids, bowl, meat grinder, upper plate, blender with soapy
water, rinse and dry thoroughly, wipe the main unit and base with damp soft cloth.
Setting up and assembling of the bowl and accessories:
Before assembling bowl and accessories, make sure the power cord is disconnected.
1. Turn the level knob (7) in anti-clockwise direction to lift the head of appliance.
2. Assemble the mixing bowl filled with ingredients, then lock it clockwise.
3. Insert the kneading hook or the egg whisk or the mixing blade into the drive shaft and lock it
clockwise
4. Press the swiveling arm downwards by turning the level knob in clockwise direction.
Instruction manual
8
Setting up and assembling of the blender:
1.
Before placing the blender make sure the power cord is disconnected.
2.
Put the blender jar on the drive shaft vertically without rotating it. Do the same by removing the
mixer.
Setting up and assembling of the meat grinder:
1.
Before assembling the meat grinder, make sure the power cord is disconnected and blender
cover well fitted.
2.
Turn the level knob so as to move the head of mixer downwards.
3.
Remove the safety cover of meat grinder (16) clockwise.
4.
To assemble the funnel (13):
Introduce the feed screw (12) into the funnel, long end first
Push the cutting blade (11) on the feed screw with the blade facing the front. If not fitted properly,
meat will not ground.
Add the disc (8/9/10) you want to use after the cutting blade, fitting protrusions in the slots.
Support or press the center of the cutting plate with one finger then screw the lock ring (2) until
tight with another hand. Do not over tighten.
Instruction manual
9
5.
Put the funnel into the housing hole by turning it right side first, push the locking button and in the
same time lock it by turning it anti clockwise.
6.
Place the hopper plate (14) on the funnel (13) and fix into position above the motor block.
Setting up and assembling for sausage making:
1. Place sausage adapter (3) on the feed screw.
2. Insert the sausage funnel (1) in the lock ring (2).
3. Turn the lock ring with the sausage attachment clockwise onto the feed screw.
Commenté [RH1]: Pour le sortir ? pour le monter à ce
stade
si oui, il faut préciser que c’est pour le sortir
Instruction manual
10
Then proceed as above point 5 and 6 meat grinder description
Note: Assemble first a blade and a perforated disc as described under “Meat Grinder Assembly” if you want
to grind meat and produce sausages in a single operation. Turn the lock ring with the sausage attachment.
Setting up and assembling for pasta making:
1. Do the same as preparation for meat grinder but by selecting a pasta attachment (4 or 5 or 6 or 7).
2. Place the attachment on the feed screw.
Turn the lock ring clockwise onto the feed screw.
Then proceed as above point 5 and 6 meat grinder description
USE OF APPLIANCE
Use of kneading function
1. To mix or knead dough:
Our suggestion of quantity to knead: flour 1000g and water 720g.
When filling the mixing bowl, please ensure that the maximum quantity 1500g is not exceeded.
Instruction manual
11
The kneading hook or flat beater should be used.
Adjust firstly Speed 1 to mix 10 seconds, then speed 2 to mix 10 seconds, afterwards Speed 3 for
about 3 minutes.
Use the tool no longer than 10 minutes continuously at a time and keep it 20 minutes to cool down
Max flour amount on mixing bowl: 1.5kg
2.
Whipping egg whites or cream
The egg whisk should be used
Switch on speed 4 to speed 6, whip the egg whites without stopping for about 5 minutes, according to
the size of the eggs, until stiff.
Maximum quantity is 24 eggs.
For whipped cream, whip 250ml fresh cream at speed 4 to 6 for about 5 Minutes.
When filling the mixing bowl with fresh milk, cream or other ingredients, please ensure that the
maximum quality is not exceeded.
Use egg whisk no more than 15 minutes continuously at a time and let it cool down for 15 minutes
To mix with the blender:
Place vegetables, fruits and water or ice into the glass blender.
Note: Prepare vegetables and fruits for processing by slicing roughly into cubes. Remove fruits pips or
peel.
For best results, do not place too many solid into the glass jar.
Be careful for blending hot liquid. Avoid hot or boiling liquids.
When blend liquid and solid food, put first a little bit of liquid inside the jar, then add the food to mix.
You can then insert more liquid from the hole.
Proceed as above description to assemble the appliance parts.
Use speed 5 -6 to blend, when crushing ice, use pulse mode.
After use switch the unit off and unplug it from the power supply.
Continuous blending time should be 4 min max.
Max liquid amount on blender: 1.5L
To mince or realize noodles with the meat grinder
Proceed as above description to assemble the appliance parts.
Cut your meat in small pieces so that they fit easily into the hopper opening.
Put your meat (or your dough for noodles) on the hopper plate.
You can use the pusher to facilitate the passage of the meat on the grinder.
Use only speed 6.
Then, you can also use the adequate accessories if you want to realize sausages or
noodles (see assembly indications above).
Instruction manual
12
After use switch the unit off and unplug it from the power supply
Continuous mincing time should be 15 min max.
Note about sausage:
Never prepare very thick sausages in order to avoid any pressure on casing
Soak the casings for around 10-15 minutes in warm water to make them flexible
Push the ingredients into the food container and slowly take off the casing from the container
Note about noodles:
The dough should be evenly kneaded, slightly moist and granular. The dough should have the
consistency of pea-sized little lumps of dough which are not too dry or too moist.
The dough is too dry if it has a powdery consistency. Add more liquid (water or vegetable juice) by
the teaspoon until the dough has assumed a granular consistency of pea-sized little lumps of dough.
The dough is too moist if large lumps of dough remain stuck to the kneading spiral. Add flour by the
teaspoon until the dough has assumed a granular consistency of pea-sized little lumps of dough.
If you add a little bit of olive oil to the pasta dough, it will slide better through the outlet openings of
the pasta attachments.
Sprinkle flour on your pasta directly as it emerges from the outlet opening and place it down
separated on a smooth floured surface to dry. This will prevent the pasta from sticking together.
Fresh pasta can be kept for approx. 1-2 days in the fridge and frozen in the freezer for as long as six
months. To stop the pasta from sticking, you should lay the pasta out to dry for approx. 1-2 hours
before you store it in the fridge or freeze it.
Continuous grinding time should be 15 min max.
Continuous making noodles time should be 10 min max.
CLEANING AND STORAGE
Before cleaning place the speed control knob at the position of “0” and disconnect the appliance from
mains power supply.
After use keep the appliance to cool down before you start to clean it.
Do not immerse the appliance into water.
Do not use a wire brush or other abrasive utensils for cleaning and do not use aggressive or abrasive
cleaning agents.
Cleaning of motor housing only with a damp cloth and a squirt of washing-up liquid. Dry with a cloth
Cleaning of accessories: kneading hook, mixing blade, eggs whisk, funnel sausage, hopper plate, feed
screw, disc, blade and lock ring can be cleaned with warm water, they are not suitable for dishwasher.
Instruction manual
13
Correct disposal of the unit
(Electrical and Electronic Equipment)
(Applicable in the European Union and the rest of Europe that have adopted separate collection systems
countries)
The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed of in the normal household waste stream.
Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain and
reduce the impact on human health and the environment.
The symbol of the crossed out dustbin is marked on all products to remind the obligations of separate collection.
Consumers should contact their local authority or retailer for information concerning the correct disposal of their product.
Photo no contractual
Worried about the quality of his products the manufacturer reserves the right to make modifications without advance
notice
LIVOO
BP 61071
67452 Mundolsheim-FRANCE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Livoo DOP189N User manual

Category
Small kitchen appliances
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI