Velleman K8018B Owner's manual

Type
Owner's manual

This manual is also suitable for

Connect to your computer and create
your own 3D LED effect.
K8018W (White LED)
K8018B (Blue LED)
R K8018W R K8018B
ILLUSTRATED ASSEMBLY MANUAL H8018IP’1
K8018
3D LED CUBE
5x5x5
Forum
Forum
Participate our Velleman Projects Forum
Subscribing our newsletter?, visit www.vellemanprojects.eu
Leds and how to use them
Features
LEDs: 5 x 5 x 5 = 125 LEDs• user programmable via USB • (creation of animation/scenes)
large amount of user programmable frames• frames are separately dimmable• 4 transition speeds• available frames: 3200• 5 levels LED dimming available• no coding skills required• regulated power supply: 9VDC•
Build your 3D led cube and created unlimited 3D effects. The unit
comes standard loaded with effects. Connect to your computer
(USB) and create your own!
It is advised to start with the
mini 3D LED cube MK193.
View the assembly movie of
MK193 as guideline for
assembly of the LEDs.
Expert soldering
skills required!
For software, visit www.vellemanprojects.eu
Supply voltage (V) - led voltage (V)
required current (A) = series resistance (ohms)
required current (A) = series resistance (ohms)
Required resistor power handling=
voltage over resistor x current passed trough resistor
9V - 1.7V
0.005A = 1460 ohm
9V - (3 x1.7V)
0.005A = 780 ohm
(9V - 1.7V) x 0.005A = 0.036W
closest value :
use a 1k5 resistor
use an
820 ohm resistor
a standard 1/4W resistor
will do the job
Supply voltage (V) - (number of leds x led voltage (V))
How to Calculate the series resistor:
Example: operate a red led (1.7V) on a 9Vdc source.
Required led current for full brightness: 5mA (this can be found in the datasheet of the led)
LEDs in series:
Example: 3 x red led (1.7V) on 9V battery
Required led current for full brightness: 5mA
(this can be found in the datasheet of the led)
Ledsfeatureaspecicvoltage
drop, depending on type and
colour. Check the datasheet for
exact voltage drop and rated
current !
Never connect leds in parallel
Leds and how to use them
An open collector output can be compared to a switch which switches to
ground when operated
Example: How to switch an LED by means of an open collector output
open collector outputs
Build your 3D led cube and created unlimited 3D effects. The unit
comes standard loaded with effects. Connect to your computer
(USB) and create your own!
assembly
hints
- 5 -
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
A good quality soldering iron (25-40W) with a small tip.• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and • will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
Thinraisin-coresolder.Donotuseanyuxorgrease.• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot •
ytowardstheeyes.
Needle nose pliers, for bending leads, or to hold components in place.•
SmallbladeandPhillipsscrewdrivers.Abasicrangeisne.•
For some projects, a basic multi-meter is required, or might be handy )
1.2 Assembly Hints :
Make sure the skill level matches your experience, to avoid disappointments.• Follow the instructions carefully. Read and understand the entire step before you perform each operation. • Perform the assembly in the correct order as stated in this manual• Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. • Values on the circuit diagram are subject to changes, the values in this assembly guide are correct*• Use the check-boxes to mark your progress.• Please read the included information on safety and customer service•
*Typographicalinaccuraciesexcluded.Alwayslookforpossiblelastminutemanualupdates,indicatedas‘NOTE’onaseparateleaet.
1.3 Soldering Hints :
Mount the component against the PCB surface and carefully solder the leads1.
Make sure the solder joints are cone-shaped and shiny2.
Trim excess leads as close as possible to the solder joint3.
0.000
- 6 -
- 5 -
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
A good quality soldering iron (25-40W) with a small tip.• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and • will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
Thinraisin-coresolder.Donotuseanyuxorgrease.• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot •
ytowardstheeyes.
Needle nose pliers, for bending leads, or to hold components in place.•
SmallbladeandPhillipsscrewdrivers.Abasicrangeisne.•
For some projects, a basic multi-meter is required, or might be handy )
1.2 Assembly Hints :
Make sure the skill level matches your experience, to avoid disappointments.• Follow the instructions carefully. Read and understand the entire step before you perform each operation. • Perform the assembly in the correct order as stated in this manual• Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. • Values on the circuit diagram are subject to changes, the values in this assembly guide are correct*• Use the check-boxes to mark your progress.• Please read the included information on safety and customer service•
*Typographicalinaccuraciesexcluded.Alwayslookforpossiblelastminutemanualupdates,indicatedas‘NOTE’onaseparateleaet.
1.3 Soldering Hints :
Mount the component against the PCB surface and carefully solder the leads1.
Make sure the solder joints are cone-shaped and shiny2.
Trim excess leads as close as possible to the solder joint3.
- 6 -
DO NOT BLINDLY FOLLOW THE ORDER OF THE
COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR
VALUE ON THE PARTS LIST!
- 7 -
- 8 -
Construction
R...
R1, R2 : 2K2 (2 - 2 - 2 - B) R3 : 10 (1 - 0 - 0 - B) R4 ... R8 : 390 (3 - 9 - 1 - B) R9 : 4K7 (4 - 7 - 2 - B) R10 : 470 (4 - 7 - 0 - 0 - 1) R11 : 1K1 (1 - 1 - 0 - 1 - 1)
Resistors
Ceramic Capacitors
C2..C6, C8 : 100nF (104)
Diodes (Check polarity!)
CATHODE
D...
D1...D3: 1N4007
4
2
1
SMD IC
3
Quartz crystal
5
X1 : 12MHz
X1
IC2, IC3: STP16CP05
Watch the position of the notch!
IC socket
6
IC1: 28p
LD1 : 3mm RED
Watch the
polarity!
LED
7
SW...
SW1 : Mode SW2 : SPEED
Push buttons
8
Ceramic Capacitors
9
c...
C7 : 470nF (474) C10 : 10nF (103) C11, C12 : 22pF (22)
1
ICSP SERVICE
ONLY
USB
SK4
WWW.VELLEMAN.EU
P8018'1 3D LED CUBE
5x5x5 = 125 LEDS
MODESPEED
9V DC
USB
CONTROLLER-PCB
5x5x5 = 125 LEDS
P8018'1 3D LED CUBE
WWW.VELLEMAN.EU
this side faces down!
On final assembly
OK!
NOT OK!
A
C
SK5
C
A
C
A
C
A
C
A
C
A
LED-PCB
PLANE-1
PLANE-2
PLANE-3
PLANE-4
PLANE-5
R11
R3
C14
IC1
C1 C2
C3
C4C5
C6
C7
C8
C9
C10
C11
C12
C13
COL1.1
COL1.2
COL1.3
COL1.4
COL1.5
COL2.1
COL2.2
COL2.3
COL2.4
COL2.5
COL3.1
COL3.2
COL3.3
COL3.4
COL3.5
COL4.1
COL4.2
COL4.3
COL4.4
COL4.5
COL5.1
COL5.2
COL5.3
COL5.4
COL5.5
D1
D2
D3
IC3
PLANE1
PLANE2
PLANE3
PLANE4
PLANE5
R1
R2
R4
R5
R6
R7
R8
R9
SK1
SK2
SK3
SW1SW2
T1
T2
T3
T4
T5
X1
IC2
LD1
R10
VR1
1x3mm
P8018 - TOP
!Watch the position of
the notch!
10
J ...
J ...
11
12
13
- 7 -
- 8 -
Construction
IC socket
6
IC1: 28p
LD1 : 3mm RED
LED
7
SW1 : Mode SW2 : SPEED
Push buttons
8
Ceramic Capacitors
9
C7 : 470nF (474) C10 : 10nF (103) C11, C12 : 22pF (22)
C...
Female Header
10
Watch the
polarity!
C9 : 4,7µF C13 : 100µF C14 : 10µF C1 : 470µF
J ...
J ...
SK4 : 30pins
Transistors
11
T1 ... T5 : BC640
DC-Jack
12
SK3 : 9VDC
USB connector
13
SK2
Electrolytic capacitors
14
IC
13
Watch the position
of the notch!
IC1: VK8018
(programmed PIC18F27J53ISP)
!
P8018 - BOTTOM
1
ICSP SERVICE
ONLY
USB
SK4
WWW.VELLEMAN.EU
P8018'1 3D LED CUBE
5x5x5 = 125 LEDS
MODESPEED
9V DC
USB
CONTROLLER-PCB
5x5x5 = 125 LEDS
P8018'1 3D LED CUBE
WWW.VELLEMAN.EU
this side faces down!
On final assembly
OK!
NOT OK!
A
C
SK5
C
A
C
A
C
A
C
A
C
A
LED-PCB
PLANE-1
PLANE-2
PLANE-3
PLANE-4
PLANE-5
R11
R3
C14
IC1
C1 C2
C3
C4C5
C6
C7
C8
C9
C10
C11
C12
C13
COL1.1
COL1.2
COL1.3
COL1.4
COL1.5
COL2.1
COL2.2
COL2.3
COL2.4
COL2.5
COL3.1
COL3.2
COL3.3
COL3.4
COL3.5
COL4.1
COL4.2
COL4.3
COL4.4
COL4.5
COL5.1
COL5.2
COL5.3
COL5.4
COL5.5
D1
D2
D3
IC3
PLANE1
PLANE2
PLANE3
PLANE4
PLANE5
R1
R2
R4
R5
R6
R7
R8
R9
SK1
SK2
SK3
SW1SW2
T1
T2
T3
T4
T5
X1
IC2
LD1
R10
VR1
1x3mm
J ...
MOUNT ON TOP-
OVERLAY SIDE
VR1 : LM317
Voltage regulator
15
- 9 -
- 10 -
Construction
ASSEMBLY OF THE LEDS
Step 1 x 100
Bend
a
+
2mm
C
+ 2mm
C
Step 2 x 20
Solder !Bend
Step 3 x 4
Solder
CUT
Step 4
View the assembly movie of MK193 as
guideline for assembly of the LEDs.
COLOR= 2...5
LD...
CATHODE
- 9 -
- 10 -
Construction
ASSEMBLY OF THE LEDS
Solder
Bend
Solder
Step 4 Step 5
Step 6
x 1 x 25
x 5
A
Bend
a
+
2mm
C
Solder !Bend
- 11 -
- 12 -
Construction
Solder
CUT
Step 7 Step 8
x 1 x 1
Solder
C
!
C
Step 9
- 11 -
- 12 -
Construction
Step 9 Step 10
Solder
Step 11
- 13 - - 14 -
Software PCB
Donwload the LEDcube software on our website www.velleman.eu
Create, edit or remove your own
animation
Help instructions
Choose 5x5 to send or read the
animations of your 5x5x5 LED
cube.
For software, visit www.vellemanprojects.eu
- 13 - - 14 -
PCB
- 15 -
VPP
1VDD
2GND
3PGD
4PGC
5
ICSP CONNECTORSK1
GND
1N4007
D1
GNDGND
470µ-25V
C1
SDO
22 SDI
2CLK
3
LE/DM1
4
VDD 24
OUT0 5
OUT1 6
OUT2 7
OUT3 8
OUT4 9
OUT5 10
OUT6 11
OUT7 12
OUT8 13
OUT9 14
OUT1015
OUT1116
OUT1217
OUT1318
OUT1419
OUT1520
GND
1
R-EXT
23
OE/DM2
21
STP16CP05MTR
IC2
GND
+5Vpic
+5Vpic
GND
PLANE1
PLANE2
PLANE3
PLANE4
PLANE5 COL5.5
COL5.4
COL5.3
COL5.2
COL5.1
COL4.5
COL4.4
COL4.3
COL4.2
COL4.1
COL3.5
COL3.4
COL3.3
COL3.2
COL3.1
COL2.5
COL2.4
COL2.3
COL2.2
COL2.1
COL1.5
COL1.4
COL1.3
COL1.2
COL1.1
SDO
22 SDI
2CLK
3
LE/DM1
4
VDD 24
OUT0 5
OUT1 6
OUT2 7
OUT3 8
OUT4 9
OUT5 10
OUT6 11
OUT7 12
OUT8 13
OUT9 14
OUT1015
OUT1116
OUT1217
OUT1318
OUT1419
OUT1520
GND
1
R-EXT
23
OE/DM2
21
STP16CP05MTR
IC3
COL1.1
COL1.2
COL1.3
COL1.4
COL1.5
COL1.1
COL1.2
COL1.3
COL1.4
COL1.5
COL2.1
COL2.2
COL2.3
COL2.4
COL2.5
COL3.1
COL3.2
COL3.3
COL3.4
COL3.5
COL4.1
COL4.2
COL4.3
COL4.4
COL4.5
COL5.1
COL5.2
COL5.3
COL5.4
COL5.5
COL2.1
COL2.2
COL2.3
COL2.4
COL2.5
COL3.1
COL3.2
COL3.3
COL3.4
COL3.5
COL4.1
COL4.2
COL4.3
COL4.4
COL4.5
COL5.1
COL5.2
COL5.3
COL5.4
COL5.5
PLANE1
PLANE2
PLANE3
PLANE4
PLANE5
PLANE1
PLANE2
PLANE3
PLANE4
PLANE5
GND
GND
+5Vpic
+5Vpic
GND
GND
2K2
R1
2K2
R2
GND
GND
GND
VUSB
1USB_D-
2USB_D+
3GND
4
6
5
USB CON MINISK2
D-
D+
D-
D+
GND
100n
C6
100n
C5
100n
C4
100n
C3
100n
C2
470N
C7
GND
100n
C8
4µ7
C9
GND
3R01
OE
BUTTON 2
10n
C10
+5Vpic
GND
4K7R9
+5V
GND
22P
C12
22 P
C11
BC640
T1
4R 093
+5V
GND
BC640
T2
5R093
+5V
BC640
T3
6R093
+5V
BC640
T4
7R093
+5V
BC640
T5
8R093
+5V
SW
-
+
DC JACK
SK3
KRS0611SW1
KRS0611SW2
GNDGND
1N4007
D3
+5V
1N4007
D2
100µ/16-25V
C13
12MH z
X1
RA0/AN0/C1INA/ULPWU/RP0
2RA1/AN1/C2INA/VBG/RP1
3RA2/AN2/C2INB/C1 IND/C3INB/ VREF-/CVREF
4RA3/AN3/C1INB/VREF+
5
VDDCORE/VCAP
6
RA5/AN4/C1INC/SS1/HLVDIN /RCV/RP2
7RB0/AN12/C3IND/INT0/RP321
RB4/CCP4/K BI 0/SC K1 /SCL1/RP725
RB2/AN8/C2 INC/CTED1/VMO/REFO/RP5 23
RB3/AN9/C3 INA/ CTED2/VPO/RP624
RB1/AN10/C3INC/RTCC/RP4 22
RB5/CCP5/K BI 1/S D A1/RP8 26
RB6/CCP6/K BI 2/PG C/ RP927
RB7/CCP7/K BI 3/P G D/RP10 28
RC0/T1OSO/T1 CKI/RP11 11
RC1/CCP8/T1OSI/UOE/RP1212
RC2/AN11/C2IND/C TPLS/RP1 313
VUSB 14
RC4/D-/VM15
RC5/D+/VP16
RC6/CCP9/TX1/CK1/RP1717
RC7/CCP10/RX1/DT1/ SDO1 /RP1818
VSS1
8VSS2
19
MCLR
1
RA7/OSC1/CLKI
9RA6/OSC2/CLKO
10
VDD 20
PIC1 8F27J53-I/ SP
IC1
BUTT ON 2BUTTON 1
BUTTON 2
BUTTON 1
SDI
CLK
LATCH
OE
LATCH
OE
CLK
OE
CLK
LATCH
SDI
ELCO RA D 10µ
C14
IO
ADJ
LM317VR1
470
R10
1K1
R11
GND
LED3RL
LD1
GNDGND
Diagram
The new Velleman Projects catalogue is
now available. Download your copy here:
www.vellemanprojects.eu
Modicationsandtypographicalerrorsreserved-©Vellemannv.H8018’IP
Velleman NV, Legen Heirweg 33 - 9890 Gavere.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Velleman K8018B Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI