Ferm SSM1001 Owner's manual

Page is loading ...

Ferm 43

EXPLODED VIEW

FFZ-400N SCROLL SAW MACHINE

The following warning symbols are used in this operating

manual:

Danger of fatal injury and possible damage to

the machine if the instructions in this manual are

not observed.

An electric current is present.

Carefully read this operating manual before commissio-

ning the machine. Acquaint yourself with its function and

operation. Maintain the machine in accordance with the

instructions so that it will always work faultlessly. This ma-

nual and the accompanying documentation must be sto-

red near the machine.

SPECIAL SAFETY REGULATIONS

When using an electric machine, always observe the

local safety regulations with regard to the risk of fire,

electric shock and injury. In addition to the following

instructions, read the safety regulations in the rele-

vant special section.

• Always wear safety glasses and a dust mask.

• Use this scroll saw machine only indoors.

• Ensure that the teeth of the saw point downwards be-

fore using the machine.

• If any of the saw blade's teeth are missing or damaged,

immediately replace the blade.

• Instal the scroll saw machine on a level, stable surface.

• To avoid breaking the saw blade, never exert lateral

pressure on it.

• Before cutting, check wooden work pieces for protru-

ding nails etc.; remove any found.

• Do not touch the surface area to be sawed.

• Do not allow the saw machine to run unattended.

•When the machine is operational, wood remnants etc.

near the saw blade must not be removed by hand. De-

activate the machine before removing remnants.

TECHNICAL DATA

Voltage 230 V~

Frequency 50 Hz

Power consumption 90 W

Speed count w/o load/min 1440

Max saw depth 90° 50 mm

Max saw depth 45° 15 mm

Weight 15 kg

L

pa

(sound pressure) w/load 62.6 dB(A)

L

pa

(sound pressure) w/o load 66.4 dB(A)

Electrical safety

Check that the mains voltage corresponds to the voltage

listed on the rating plate.

Mains connection

Only use earthed sockets with earthing wire connected

per the regulations.

Replacing the mains connection cable

The mains connection cable may only be replaced by a

special cable in a specialised workshop.

Replacing cables or plugs

Dispose of old cables or plugs immediately after replacing

them. It is dangerous to connect the plug of a loose cable to

a wall socket.

Using extension cables

Only use an approved extension cable, corresponding to

the machine power use. The wires must have a minimum

cross section of 1.5 mm

2

. If the cable is on a reel, it must be

fully paid out.

CONTENT OF THE PACKING

1 scroll saw

1 protective cover

1 screw for installing the protective cover

2 saw blades

2 adapters for universal saw blades

2Allen key

1 dust blow pipe

3 rubber feet

3 screws with nuts and rings for installing the rubber feet

1cross guide

1 operating manual

1 safety manual

1 warranty card

Check the machine, loose parts and acces-

sories for transport damage.

UK

English

2 Ferm

42 Ferm

SPARE PARTS

REF.NR. DESCRIPTION FERM NR.

015 - 020 BOLSTER THREADED COMPLETE 209860

023 PRESSING PLATE 209861

024 SPRING 209862

025 BUSHING 209863

026 UPPER ARM 209864

028 SAW BLADE HOLDER (UPPER) 209865

033 + 034 CONNECTION PLATE + BEARING 209866

039 LOWER ARM 209867

041 SAW BLADE HOLDER (LOWER) 209868

042 - 044 AIR HOSE + PLASTIC PLATE 209869

047 TRANSPARENT GUARD 209870

049 GAS BAG 209871

052 CAM 209872

055 TABLE INSERT 209873

056 MOTOR 209874

065 SUPPORT FRAME 209875

069 - 072 MITRE GUIDE COMPLETE 209876

SWITCH 209877

ERSATZTEILVERZEICHNIS

REF.NR. BEZEICHNUNG FERM NR.

015 - 020 STIFT KOMPLETT 209860

023 DRUCKPLATTE 209861

024 FEDER 209862

025 BÜCHSE 209863

026 OBEN ARM 209864

028 SÄGEANGEL (OBEN) 209865

033 + 034 ÜBERTRAGUNG INKLUSIVE LAGER 209866

039 UNTERARM 209867

041 SÄGEANGEL (UNTER) 209868

042 - 044 SCHLAUCHANSCHLUß + SCHLAUCH 209869

047 SCHUTZGEHAUSE 209870

049 STAUBBLASVORRICHTUNG 209871

052 EXZENTER 209872

055 TISCHEINSATZSTÜCK 209873

056 MOTOR 209874

065 TISCHHALTER 209875

069 - 072 GRADBOGEN KOMPLETT 209876

SCHALTER 209877

DESIGNATIONS

Fig. A.

1. On/off switch

2. Locking arm

3. Cross guide

4. Dust blow pipe

5. Protective cover

6. Tensioner head

INSTALLING ACCESSORIES

Fig. B.

Always disconnect the machine from the mains

before carrying out any maintenance work

Installing the protective cover

• Before commissioning the machine, the protective co-

ver (5) must be installed.

5

A

1

2

6

4

3

5

Ferm 3

VEDLIGEHOLDELSE

Afbryd maskinen fra nettet, når du skal udføre

servicearbejde på de mekaniske dele.

Maskinen er udviklet til at kunne fungere problemfrit i lang

tid og med et minimum af vedligeholdelse. Du forlænger

maskinens levetid ved at rengøre den regelmæssigt og

behandle den fagligt korrekt.

Rengøring

Rengør regelmæssigt maskinens kabinet med en blød

klud, og helst hver gang du har brugt den. Hold blæseråb-

ningen fri for støv og snavs.

Fjern fastsiddende snavs med en blød klud fugtet med

sæbevand. Anvend ikke opløsningsmidler som benzin,

alkohol, ammoniak, osv. Sådanne midler beskadiger

kunststofdele.

Smøring

Maskinen behøver ikke nogen yderligere smøring.

Fejl

Hvis der opstår en fejl, f. eks. på grund af slitage på en

komponent, bedes du henvende dig på den serviceadres-

se, som er angivet på garantibeviset.

MILJØ

For at forhindre transportskader leveres maskinen i en so-

lid emballage. Emballagen består i vidt omfang af mate-

riale, som kan genbruges. Udnyt derfor muligheden for

indlevering af emballagen til en genbrugsstation.

GARANTI

Læs garantibetingelserne på det vedlagte garantibevis.

ClEl

■

OVERENSSTEMMELSESERKLÆRING

(

DK

)

Vi erklærer hermed, at

dette produkt er i overensstemmelse med

følgende standarder eller normative dokumenter:

EN61029-1, EN55014-1, EN55014-2,

EN61000-3-2, EN61000-3-3

i henhold til bestemmelserne i følgende direktiver:

98/37/EØF

73/23/EØF

89/336/EØF

Fra

01-12-2002

GENEMUIDEN NL

W. Kamphof

Quality department

Ferm 41

Installing the cross guide

Fig. C.

The cross guide (3) allows material to be bevelled, and can

be simultaneously used to support the material as it is fed

through the saw.

OPERATION

Fig. D.

Always observe the safety instructions and

obey the relevant regulations.

Tilting the table.

The scroll saw table can be tilted through 45°. To do so:

• Lock the locking arm underneath the table.

•Manually tilt the table until the desired angle has been

reached (see the graduated scale on the machine).

• Retighten the locking arm.

45°

3

4 Ferm

Montering af savklingen

Fig. E.

Afbryd maskinen fra elnettet, når du skal udføre

servicearbejde på de mekaniske dele.

Du kan få de anvendte savklinger som univer-

salsavklinger i ethvert velassorteret byggemar-

ked eller en maskinhandel.

•Ă Vælg den rigtige savklinge i henhold til trætypen.

• Løsn spændegrebet (6).

• Før savklingen gennem slidsen med tænderne ne-

dad. Sørg for, at bolten til savklingen (eller savklinge-

adapteren) glider ind i den nederste savklingeholder.

• Træk savklingen opad, så den øverste bolt (eller sav-

klingeadapter) glider ind i den øverste holder.

•Spænd spændegrebet, indtil savklingen har den nød-

vendige spænding.

• Fjern værktøj og andre genstande fra savbordet. Slå

strømmen til og lad savklingen rotere, før du begynder

at save. Kontrollér, om savklingen løber roligt.

Med de to medleverede savklingeadaptere kan

der også anvendes savklinger til løvsavsarbej-

de.

• Fastgør savklingeadapteren på savklingen (til løv-

sav). Sørg for, at unbrakoboltene er skruet lige meget

i, så savklingen ikke bliver sat skævt på og dermed ik-

ke saver præcist.

• Montér det hele i holderen i henhold til "Montering af

savklingen".

Udtagning af savklingen

Afbryd maskinen fra nettet, når du skal udføre

servicearbejde på de mekaniske dele.

• Løsn spændegrebet, indtil fjederen er slap.

• Tryk den øverste savklingeholder forsigtigt nedad, og

løft klingen lidt, så udtagningen bliver lettere.

• Lad klingen falde lidt ned, og skub den fremad, så den

kommer fri af den nederste holder.

Anvendelse

• Savklingen saver kun i den nedadgående bevægelse.

• Før langsomt og med et minimum af tryk emnet ind

mod savklingen.

• Hold emnet fast mod bordet med begge hænder, og

før det langsomt frem til savklingen, så det undgås, at

klingen knækker eller vrider sig.

• For at få et optimalt resultat skal savklingen være

skarp.

• Anvend den rigtige savklinge. Valget af savklinge af-

hænger af træets tykkelse og det ønskede snit. Gene-

relt gælder følgende: Jo tyndere og jo hårdere træet er,

desto finere skal savklingens tænder være. Anvend

en smal klinge, når du skal save skarpe rundinger.

+

—

6

40 Ferm

Installing the saw blade

Fig. E.

Always disconnect the machine from the mains

before carrying out any maintenance work.

Use universal saw blades from any better DIY

shop or machine shop.

• Select the correct blade for the kind of wood to be cut.

• Loosen the tensioner button (6).

• Push the saw blade through the slot, with the teeth

pointing downwards. Make sure that the bolt of the saw

blade (or saw-blade adapter) slides into the lower saw-

blade holder.

• Pull the saw blade up, so that the upper bolt (or saw-

blade adapter) slides into the upper holder.

• Tighten the tensioner button until the saw blade has

the required tension.

• Remove all tools and other objects from the saw table.

Activate the current and allow the saw blade to run be-

fore starting to saw. The saw blade should run quietly.

Use the saw-blade adapters included in the deli-

very to install saw blades for the compass saw.

• Fasten the saw-blade adapter (for compass saws) to

the saw blade. Make sure that the Allen bolts have

been sufficiently tightened to prevent the saw blade fr-

om being fastened obliquely and thus sawing inaccu-

rately.

• Install the assembly in the holder in accordance with

the instruction 'Installing the saw blade'.

Removing the saw blade

Always disconnect the machine from the mains

before carrying out any maintenance work.

• Loosen the tensioner head until the spring is slack.

•Carefully push down the upper saw-blade holder and

slightly lift the blade in order to facilitate its removal.

• Allow the blade to drop down slightly and push it for-

ward, in order to loosen it from the lower holder.

Using the scroll saw machine

• The saw blade saws only during the downward stroke.

• Using both hands, slowly and with minimum pressure

push the workpiece across the table towards the saw

blade. This will prevent the blade from breaking or

twisting.

• For optimal results, the saw blade must be sharp.

• Use the correct saw blade. The selection of the saw

blade depends on the thickness of the wood and the

desired cut. Generally speaking, the thinner and har-

der the wood, the finer the teeth of the saw blade must

be. Use a narrow blade to saw tight bends.

+

—

6

Ferm 5

Montering af tværføringen

Fig. C.

Tværføringen (3) bruges til at save materiale i gering, idet

tværføringen (3) samtidig kan anvendes til at støtte mate-

rialet, når du fører det gennem saven.

BETJENING

Fig. D.

Følg altid sikkerhedsanvisningerne, og hold dig

til de relevante forskrifter.

Vipning af bordet

Bordet på denne dekupørsav kan vippes 45°. Det gøres

på flg. måde:

• Løsn låsehåndtaget under bordet

• Vip bordet med hånden, indtil den ønskede vinkel er

nået.

•Vinklen kan aflæses på gradskalaen på maskinen.

• Spænd låsehåndtaget fast igen.

45°

3

Ferm 39

MAINTENANCE

Always disconnect the machine from the mains

before carrying out any maintenance work.

The machine is designed to function faultlessly for a long

period and with a minimum of maintenance. Extend its life-

span by regularly cleaning the machine and treating it cor-

rectly.

Cleaning

Regularly clean the machine with a soft cloth, preferably

after each use. Keep the ventilator slot free of dust and

other deposits.

Remove any tenacious deposits with a soft cloth moiste-

ned with soap. Do not use solvents (petrol, alcohol, ammo-

nia, etc.) as they will damage the plastic parts.

Lubrication

The machine does not need lubricating.

Faults

If a fault arises (due to e.g. element wear), contact the ser-

vice address listed on the warranty card.

ENVIRONMENT

We deliver the machine in sturdy packing in order to pre-

vent transport damage. Although the packing is mostly

made of reusable materials, please recycle it.

WARRANTY

Read the warranty stipulations on the enclosed warranty

card.

ClEl

■

CONFORMITY STATEMENT

(

GB

)

As sole responsible party, we declare that this product

corresponds to the following norms or normative

documents:

EN61029-1, EN55014-1, EN55014-2,

EN61000-3-2, EN61000-3-3

in accordance with the stipulations of the guidelines:

98/37/EEC

73/23/EEC

89/336/EEC

as from

01-12-2002

GENEMUIDEN NL

W. Kamphof

Quality department

6 Ferm

Page is loading ...

Ferm SSM1001 Owner's manual

This manual is also suitable for

Ferm SSM1001 Owner's manual

in other languages

Related papers

Other documents