Dell W-7200 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Dell W-7200 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the purpose of this document?
    Is it safe to insert or remove a power supply while the power cord is connected?
    Can a power supply be replaced without powering down the device?
    What steps do I need to take to install a power supply module?
    How do I remove a power supply module?
Dell PowerConnect W-7200 Series PSU-350-AC
Installation Guide
0511261-01 | January 2013 1
This document describes how to install a 350W AC Power Supply (PSU-350-AC) into a Dell PowerConnect W-
7200 Series Controller. In this document, the W-7200 controller is referred to as the “device.”
Installing a Power Supply
The power supply modules are hot-swappable. Hot swapping allows you to replace a failed power supply without
powering down the device during the replacement process. This makes it unnecessary to shut down the device
during the replacement procedure.
1. With a Phillips Head screwdriver, turn the hinged captive screw counter-clockwise until it is loose (they
cannot be completely removed).
2. Firmly grasp both of the hinged captive screws and pull the spring loaded hinge down until you are sure the
hinges are disengaged.
3. Grasp the power supply blanking plate by the hinged captive screw and slide the plate out.
4. Align the new power supply module with opening in the device, as shown in Figure 1.
5. Pull down the hinged captive screw on the power supply module and align its tab with the slot on the left side
of the opening.
6. Slide the power supply module into the device.
7. Lift the hinged captive screw and secure the power supply module by tightening the screw with a Phillips
Head screwdriver. Take care not to over-tighten the screw.
CAUTION: Never insert or remove a power supply while the power cord is connected. Verify that cord has been disconnected
from the power supply before installation or removal.
NOTE: Use standard ESD precautions when installing or removing a power supply module.
NOTE: If you are adding an additional power supply module, removing the pre-installed power supply module blanking plate. If you
are replacing a failed power supply, see “Removing a Power Supply” on page2 before you continue.
2 Dell PowerConnect W-7200 Series PSU-350-AC | Installation Guide
Figure 1
Installing a Power Supply
8. Insert the power cord and secure it by lowering the power cord retaining clip over the power cord.
Removing a Power Supply
1. Lift the power cord retaining clip from the power cord.
2. Remove the power cable connected to the power supply module.
3. Using a Phillips head screwdriver, loosen the hinged captive screw on the front of the power supply module.
4. Lower the hinged captive screw as far as it can go.
5. Using the power supply module’s handle, pull the module out.
6. If you are not replacing the removed power supply module, install a blanking plate that was include with your
device by following the installation procedure under “Installing a Power Supply” on page1.
Dell PowerConnect W-7200 Series PSU-350-AC | Installation Guide 3
This page is intentionally left blank.
Copyright
© 2013 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks
®
, Aruba Wireless Networks
®
, the
registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System
®
. Dell™, the DELL™ logo, and PowerConnect™ are
trademarks of Dell Inc.
All rights reserved. Specifications in this manual are subject to change without notice.
Originated in the USA. All other trademarks are the property of their respective owners.
Open Source Code
Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General
Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The Open Source code used can be found at
this site:
http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors’ VPN client
devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc.
from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors.
4 Dell PowerConnect W-7200 Series PSU-350-AC | Installation Guide
Contacting Support
Website Supportain Website
Main Site dell.com
Support Site dell.com/support
Documentation Site dell.com/support/manuals
/