Figure I
AUTO SAFETY SHUT-OTF WITH TIP-OVER
PROTEfiION:
This heqter is equipped with o
polented,
lechnologicolly-odvonted
sofef syslem
fiol requires fie user lo resel fie heoler if ftere
is
o
polenliol
overheol siluolion. When o
polentiol
overheol lem-
perolure
is reoched, fie sy$em will outomolicolly shd
fie heoter
off. lt ron only resume operolion
when lhe user resels lhe unil.
TO RISTT THt HEAIER:
l.
Unplug
fte heoler ond woit l0 minules for lhe unil lo cool
down.
2. Afler fie
l0 minules,
plug
fie unil in ogoin ond operole
normolly.
IIP-OVER PROTIfiION:
When fie heoler is oaidenlolly
knocked over, il will oulomolitolly
shul off.
Io reset, simply
plore
fte heoler in on upright
posilion.
Pres fie M0DE builon ond operole normolly.
PRE-OPERATING INSTRUCTIONS
l.
(orefully
remove
your
heoler from ile box.
(pleose
sove the
corlon for off-seoson $oroge).
2. Plore heoler on firm level surfoce.
3. Avoid overlooding
your
circuit by
nol using ofier high
wolloge opplionres
in lhe some ouilel. Al 1500 Wolls, fiis
unil drows I 2.5 Amps.
NOIt: Ihe
power
light
will remoin lil when
plugged
in.
AC(UTEMP PLUSTM DIGITA!. THERMOSTAT
Your heoter h equipped wilh on AauTemp PlusTM Digitol
Thermo$ol fiol ollows
you
l0 sel
your
heoler lo
your precise
comfort
level.
SETTING
THT A((UIEMP PI.USTM IHERMOSTAT:
I . Pres fte Mode Bufton for monuol Hl
power.
Ihe heoler will
run ronlinuoudy
ol I 500 Wolls.
2.
Press ile Mode Bullon ogoin for monuol L0
power.
The
heoler
will run ronlinuously ol 1000 Wolls.
3. Pres fie Mode Bullon for o third time for Aulo Mode
Hl
Power
(AH)
(l
500 Wolh) or
pres
ogoin for Aulo Mode L0
Power
(AL) (
I 000 Wotts). ln either of
these modes
you
moy
fien
pres
fte up,
ond down builons lo reoch
your
desired
lemperolure
4. 0nce
you
hove selecled
your
desired lemperolure, lhe
disploy will relurn lo exisling room lemperolure.
The heoler
will
groduolly
inrreose lhe room lemperolure until it hos
reoched
your pre-sel
lemperolure.
lf the unit will nol storl in fie AccuTemp Plus" mode,
pleose
moke sure lhe
"sel
lemperolure"
is higher thon lhe cunenl room
lemperolure.
NOIE: lt
is normol for ile heoler lo cyde 0N ond
()tF
os il
moinloins lhe
presel
temperoture. Io
prevenl
lhe unil from
cyding,
you
need lo roise fie ftermoslol selling. When the
presel
lemperolure is reorhed, fie
fon will run for 30 seconds
wilhoul
heol. Ihis cool down
process
ensures on occurole ond
(onsislenl
lemperolure reoding. lf
you
unplug fte heoler,
you
will hove lo resel lhe Aaulemp PlusTM lhermostol ogoin by
following the obove in$ructions.
N0IE: Io shul fie unil off d ony
lime,
pres
ond hold the mode
builon down
for two setonds.
N0IE: Acculemp PlusTM hos memory. The Acculemp PlusTM
fiermoslol will remember
lhe
previous
lemperolure selling ofter
fte unil
hos been lurned off. However, if fie unit is unplugged,
fie ArcuTemp PlusTM lhermoslol will be
resel ond wlll no longer
remember lhe
previous
lemperolure selling.
USING THE PROGRAMMABTT TIII|IIR
Arculgmp PlusTM lechnology ollows
the
user lo
progrom
lhe
heoler to rome on ol o
presel
lime, or lurn off ofler 0 sel omounl
of fime.
SEITING THE OTT TIMTR:
I . Seled
fte
Mode ond 0r lemperoture
you
wish
fte
heoter to
run in.
2. While the heoler is running,
pres
ond hold fie TIMP UP ond
TtMP D0WN huilons simuhoneously.
3.
By
presing
the
up ond
down builons,
progrom
lhe heoter lo
turn off up lo l6 hours loler in inoemenls of I hour.
4. After
selling fie fimer,
the IED
disploy
will
relurn lo show
lhe
currenl room lemperolure.
5. Afler $e
predelermined
length of time hos
posed,
fie
heoter will oulomolkolly shul off.
SETTING THT ON IIMER:
l.
While the heoler is off,
pres
ond hold the up ond down
bufions simultoneously.
2. By
presing
fie up ond down huflons,
progrom
lhe heoler lo
lurn on up lo I 6 hours in odvonce in inoements of I hour.
3.
Afier fie
presel
lengft
of
ilme hos
possed,
the heoter will
oulomolicolly lurn on ol lhe lo$ mode selling lhot wos
progrommed.
lf no
progrom
wos sel, lhe heoler will turn
on Aulo Mode Hl Power ol 75"F/24"(. for o
presel
lime of 2
hours.
NOT[: Anylime fte Mode button is
presed
while
fie
fimer
is
oclivoled, fie limer funclion will be concelled ond need lo be
reset.
Figure 2
TEI\,4P DISPLAY
TEN,4P & TII\IE
INCREASE
TEI\,4P & TIME
DECREASE