Vmar V STICK 40 User manual

Brand: Vmar

Model: V STICK 40

Category: Remote controlled toys

Type: User manual

VSTICK 40

Before beginning assembly,please read these intructions thoroughly.

Photograph is nitro version

INSTRUCTION MANUAL

UNDER SAFETY PRECAUTIONS

This radio control model is not a toy!

It is highly recommended that first-time builders seek advice of experienced modelers before beginning assembly.

Assemble this kit only in places out of children’s reach!

Take enough safety precautions prior to operating this model. You are responsible for ths model’s assembly and safe operation!

Always keep this instruction manual ready at hand for quick reference, even after completing the assemble.

Taking out liability insurance is recommended.

*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

The pre-covered film on ARF kits may wrinkle due to variations

of temprature. Smooth out as explained at right.

Use an iron covered with a cloth!

Start at low setting. Increase the

setting if necessary. If it is too high,

you may damage the film.

with cover (cloth)

low setting

ALMOST-READY-TO-RLY

ARTF

DANGER

Assemble in the

specified order.

Assemble left and right

sides the same way.

Drill holes with the

specified diametre.

Must be purchased

separately!

Apply threadlocker

(screw cement).

Pay attention here!

Ensure smooth, non-binding

movement when assembling.

Cut off excess.

Do not overlook

This symbol!

Warning!

Symbols used throughout this instruction manual, comprise:

Check all parts. If you find any defective or missing past, contact your local dealer or our VMARSHOP.

Read through the manual before you begin, so you will have an overall idea of what to do.

accepts no responsibility for accidents, damage or breakage if other manufacturers parts are used.

Drill,Bits (2,3,4,6mm)

Cutters Pliers

Long Nose Pliers

Shap Hobby Knife

File

Scissors

Hex Wrench (2, 2.5, 3mm)

Phillips screwdrivers (size: L, M, S)

Threat locker Cement

SCREW

CEMENT

BEFORE YOU BEGIN

TOOLS REQUIRED (Purchase separately!)

CAUTION : For detalls concerning the equlpment Ilsted below (size, make, etc.) check with your hobby shop.

ITEM REQUIRED FOR OPERATION (Not included in kit!)

A minimum 4 channel radio for alrplanes (with 5 standard servos),

and nicad or alkaline batteries are required.

4-channel (minimum) radio system for aircraft 4 servos (standard servos).

Please be sure to sure to use servos with enough torque (3.0 - cm minimum).

Y-Harness 2pcs

2-stroke .46~.55

4-stroke .70~.90

Suitable Outer Rotor Motor.

Use outer rotor motor power

between 800~1200w

Motor : KV / 600~650

ESC More than 70A

Muffler

Glow Plug

Radio Set

Engine,

Motor, ESC

Installing Servo

to the wing

< Top view of left wing >

< Bottom view of left wing >

Aileon servo location

Cut off shaded portion.

Must be purchased

separately!

2mm

Drill holes with the

specified diameter.

Assemble as many

time as specified.

Assemble left and right

sides the same way.

Pay close attention here!

TP Screw

2 x 10mm

approx. 16mm

2mm

Aileron servo arm

position

Connecting control

rod to aileron

Set all screws securely. If they come off during flight

you will lose control of your aicraft!

Waning!

Typical control horn

installations

Installing the wing

to the fuselage

NO GLUE NEDED FOR THIS ASSEMBLY

Aluminum wing joiner tube sizie 16mm diameter and 570mm long

1. Insert the wing joiner tube

to the fuselage

SURFACE CONTROL

EZ CONNECTOR

CLEVIS

3 x 15mm

Attach wing

to the fuselage

Main gear

Nose landing gear

1. Insert the wing tube onto right wing panel

the tighten with the butterfly nut to secure

to the fuselage

2 . same procedure the secure the left wing

panel to the fuselage

4x20xhex bolt

1 wooden washer

1 butterfly nut

Main wing

Horizontal tail

Set all screws securely. If they come off during flight

you will lose control of your aicraft!

Waning!

washer

3mm

security nut

3mm

security nut

3mm

washer

Linkage rod

Rudder rod

2mm

approx.2mm

Elevator rod

SUFACE CONTROL

< Bottom view.>

Servo

Supplied with

the radio.

Supplied with

the radio.

1.5mm

Front

Rudder Control Servo

Elevator Control Servo

Rudder Control Servo

Elevator Control Servo

Supplied with the Servo.

Linkage

Supplied with the Servo.

approx. 16mm

4x5mm

Linkage Stopper

2x10mm

Engine Mount

4x20mm

Hex bolt

Engine Mount

4x20mm

To Muffler

To Carburetor

Connect the fuel line to the engine

Install the fuel tank to the fuselage

Install the engine

washer

3mm

Security nut

Hex cap bolt

3 x 30mm

3x30mm

Throttle rod

Engine

3x30mm

3mm

Linkage

Supplied with the Servo.

approx. 16mm

4x5mm

2x10mm

Linkage stopper

2mm

Elevator servo

Linkage

Throttle servo

Rudder /steering servo

< Throttle Idling >

Throttle position of TX

approx. 1mm

Throttle servoCarburetor

< Throttle Hi >

< Throttle Stop >

Adjust the throttle input (transmitter throttle stick),

throttle trim movement and the carburetor opening

to the suitable position and screw in the 4x5mm set screw.

2mm

Install propeller,

spinner and muffler

Securely tighten the nut holding the propeller

for it not come off when the motor is spinning.

If coming off, there is a high risk of injury!

Warning!

Propeller

Motor Mount

version

Brushless motor

Motor mount

POWER MODULE WITH FOUR MOUNTING BOLTS

POWER

MODULE

67mm

WASHER

4mm NUT

APPLY THREAT LOCKER HERE

WASHER

APPLY THREAT LOCKER HERE

ELEVATOR

RUDDER

ALERON

High rate Low rate

75~85mm

Battery

C of G position

GP/EP

version

In order to obtain the CG specified, reposition

the receiver and other equipment

Warning!

Do not fly before confirming the correct location of the CG.

If the CG is incorrect, you lose control of your airplane which leads to accidents!

SURFACE CONTROL MOUVEMENT

Aileron movement

1/5"

6mm

1/3"

10mm

1/3"

10mm

1/5"

6mm

5/8"

16mm

5/8"

16mm

1/3"( 10mm ) up

1/5"( 8mm ) down

1 "( 25mm ) right

1 "( 25mm ) left

1/2"( 16mm ) up

1/2"( 16mm )down

1/5"( 8mm ) up

5/8" ( 16mm ) right

1/3"( 10mm ) up

1/3"( 10mm )down

1/3"( 10mm ) down

Aileron movement

Rudder movement

Fuel Tank

Typical Battery setup for electric version

Typica Fuel Tank setup for nitro version

Vmar V STICK 40 User manual

Brand: Vmar

Model: V STICK 40

Category: Remote controlled toys

Type: User manual

Download PDF

report

Vmar V STICK 40 User manual

Vmar V STICK 40 User manual

Related papers

Other documents