Asustor LOCKERSTOR 2 (AS6602T) Quick Installation Guide

Quick Installation Guide

Applicable Models

AS6602T/AS6604T

Ver.2.3.0903 (2015-3-2)

Ver. 3.5.0302(2021-3-2)

2

Table of Contents

Notices .................................................................................................................................... 3

Safety Precautions .................................................................................................................. 4

1. Package Contents .............................................................................................................. 5

2. Optional Accessories .......................................................................................................... 7

3. Hardware Installation Guide ............................................................................................... 8

Tools Needed for Hard Disk Installation .............................................................................. 8

Hard Disk Installation ........................................................................................................... 8

Securing the Power Cord................................................................................................... 10

Connecting and Powering on the NAS .............................................................................. 11

Upgrading System Memory ............................................................................................... 12

Installing M.2 SSD ............................................................................................................. 16

4. Software Installation Guide ............................................................................................... 20

Download Center Installation ............................................................................................. 20

Web Installation ................................................................................................................. 22

Installation Using a Mobile Device ..................................................................................... 23

Installation Using the LCD Display .................................................................................... 25

Installation Using a Direct Connection ............................................................................... 26

Shutting Down Your NAS .................................................................................................. 26

5. Appendix ........................................................................................................................... 28

LED Indicators ................................................................................................................... 28

Rear Panel ......................................................................................................................... 29

Operating the LCD Panel ................................................................................................... 29

Troubleshooting ................................................................................................................. 32

3

Notices

Federal Communications Commission Statement

This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part

15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

CE Mark Warning

CE marking for devices without wireless LAN/Bluetooth

The shipped version of this device complies with the requirements of the EEC directives 2004/108/EC

"Electromagnetic compatibility" and IEC60950-1:2005 (2nd Edition)+A1:2009 "Information technology

equipment-Safety ".”

4

Safety Precautions

The following safety precautions will increase the life of the NAS. Follow all precautions and instructions.

Electrical Safety

Unplug this product from the power source before cleaning.

Use only the bundled power adapter. Using other power adapters may damage your device.

Ensure that you plug the power adapter to the correct power input rating. Check the label on the power adapter

for the power rating.

Operation Safety

DO NOT place this product in a location where it may get wet.

Place this product on a flat and stable surface.

Use this product in environments with an ambient temperature between 0°C and 40°C.

DO NOT block the air vents on the case of this product. Always provide proper ventilation for this product.

DO NOT insert any object or spill liquid into the air vents. If you encounter technical problems with this

product, contact a qualified service technician or your retailer. DO NOT attempt to repair this product

yourself.

DO NOT throw this product in municipal waste.

This product has been designed to enable proper reuse of parts and recycling.

This symbol of the crossed out wheeled bin indicates that the product (electrical

and electronic equipment) should not be placed in municipal waste. Check local

regulations for disposal of electronic products.

5

1. Package Contents

Applicable Models : AS6602T, AS6604T

Model Name

AS6602T

AS6604T

Power Cord

x1

Adapter

x1

RJ45 Network Cable

x2

Power Cord Bracket

x1

Screws for use with

3.5” HDD

x8

x16

Screws for use with

2.5” HDD

x8

x16

6

Quick Installation Guide

x1

7

2. Optional Accessories

The items below may be purchased from the ASUSTOR Accessories Store http://shop.asustor.com.

8

3. Hardware Installation Guide

All data stored on the hard disk(s) will be erased and CANNOT be recovered. Please back up all

important data before initializing the system.

Tools Needed for Hard Disk Installation

 Phillips head screwdriver

 At least one 2.5 or 3.5 inch SATA hard disk. (For a list of compatible hard disks, please see

http://www.asustor.com/service/hd?id=hd)

Hard Disk Installation

1. Press the button on the lower portion of the hard disk tray to release the latch.

2. Using the latch, gently pull the disk tray out of the disk bay.

3. Mount the hard disk to the disk tray.

9

3.5-inch hard disks: Place the hard disk into the disk tray, making sure that the mounting holes on the

sides of the hard disk and disk tray are lined up. Secure the drive with four screws.

2.5-inch hard disks and SSD hard disks: Place the hard disk into the area of the disk tray outlined in

red (see picture below). Make sure that the mounting holes on the bottom of the hard disk and disk tray

are lined up. Secure the drive with four screws.

4. Slide the disk tray onto the rails of the disk bay. Using the latch, gently push the disk tray all the way into

the disk bay. Secure the disk tray in place by pushing down on the latch. The latch should close easily and

snap in with an audible ‘click’. Please make sure that the disk tray is pushed all the way into the disk bay

before attempting to secure the latch.

10

5. Once the latch is secure, you can lock it in place using the disk tray lock. Using a flathead screwdriver, turn

the lock counterclockwise to lock the latch mechanism. Turning the lock clockwise will unlock it.

Securing the Power Cord

Note: You can use the provided cord bracket to secure the power cord in place, if you are concerned

about the NAS power cord becoming detached when the NAS is moved.

1. Take the cord bracket out of the accessories box.

2. Attach the bracket to the power cord as shown in the graphic below.

3. Remove the fan screw by unscrewing it counter-clockwise.

AS6602T AS6604T

11

4. Position the bracket over the hole for the removed fan screw. Secure the bracket in place by replacing the

fan screw.

AS6602T

AS6604T

Connecting and Powering on the NAS

1. Connect the NAS to its power supply.

2. Connect the NAS to your router, switch or hub using an Ethernet cable.

AS6602T AS6604T

12

3. Press and hold down the power button for 1 – 2 seconds until the blue power LED indicator is lit. This

indicates that the NAS is now powered on. While the NAS is being powered on, the green system status

LED indicator will flash and the blue network LED indicator will be lit as well.

4. The NAS is ready for operation once the green system status LED indicator has stopped flashing and

remains steadily lit. At this time, you should also hear a ‘beep’ from the system buzzer. Hardware installation

is now complete. Please move on to the software installation guide to configure your system settings.

Upgrading System Memory

Notes and Precautions

All AS66 Series NAS devices support up to 8GB of memory. Before adding or removing memory modules,

please read the following precautions thoroughly.

 Your NAS and memory modules use high precision components and electronic connector technology. To

avoid invalidation of the warranty during your product warranty period, we recommend that:

 Memory for AS66 series devices may be purchased from local dealers or the online ASUSTOR

Accessories Store (http://shop.asustor.com).

 You should not install a memory module by yourself, if you are not familiar with upgrading memory on a

computer.

 You should not touch the connectors or open the memory module compartment cover.

 Addition or removal of memory modules by yourself may result in an accident or malfunction of your NAS

caused by breakage of the slot and module or a connection mistake. In this case, a repair fee will be charged.

 Be careful not to injure your hands or fingers with sharp edges of the memory module, inner components, or

circuit boards of your NAS.

 ASUSTOR does not guarantee that third party memory modules will work in your NAS.

13

 Be sure to turn off your NAS and peripherals and disconnect all attachments and connection cables before

adding or removing memory modules.

 To prevent damage from electrostatic discharge to memory modules, follow the instructions below:

 Do not work at a location that produces static electricity easily, such as on a carpet.

 Before adding or removing memory modules, touch an external metal object other than your NAS to

ground yourself and eliminate static electricity. Do not touch any metal parts inside the NAS.

 Do not insert a memory module into the slot facing in the wrong direction. It may cause damage to the

module or slot, or cause the circuit board to catch fire.

 Use a screwdriver that matches the size of the screws.

 Do not remove or loosen screws that are not specified to be removed.

Parts and Tools Needed

Phillips head screwdriver

Removing the Cover

1. Shutdown the NAS by selecting [Shut down] from the ADM User Menu.

2. Disconnect all cables and devices connected to the NAS including the power cord.

AS6602T AS6604T

14

3. Use a screwdriver to loosen the three screws found on the rear of the NAS as shown in the illustration.

AS6602T AS6604T

4. Grip the cover from both sides with two hands and then gently push it back to remove it from the chassis.

AS6602T AS6604T

Installing Memory

1. Upon opening the NAS, RAM slots can be found on the motherboard on the left hand side of the NAS.

Insert a DIMM into an empty slot at a 45° angle and align the notches of the RAM and the slot.

15

2. Gently push the DIMM down until both latches click into place. RAM should be flush with the motherboard.

Replacing the Cover

1. Replace the cover and tighten the three screws that were removed previously.

AS6602T AS6604T

2. Reconnect all cables including the power cord and then start up the NAS.

AS6602T AS6604T

16

Installing M.2 SSD

M.2 Installation Precautions

The AS6602T and AS6604T provide two M.2 SSD slots. For maximum compatibility, click here for a list of

compatible M.2 SSDs.

Parts and Tools Needed

Phillips head screwdriver

Removing the Cover

1. Shutdown the NAS by selecting [Shut down] from the ADM User Menu.

2. Disconnect all cables and devices connected to the NAS including the power cord.

AS6602T AS6604T

17

3. Use a screwdriver to loosen the three screws found on the rear of the NAS as shown in the illustration.

AS6602T AS6604T

4. Grip the cover from both sides with two hands and then gently push it back to remove it from the chassis.

AS6602T AS6604T

Installing M.2 Drives

1. Remove the two screws to free the SSD carrier board as shown in the figure below.

AS6602T AS6604T

2. Firmly grasp the SSD carrier board and gently pull it out of its slot.

AS6602T AS6604T

18

3. If installing one SSD, the first SSD should be installed into slot 2 underneath the SSD carrier board. Slot1 is

facing up when installed.

4. Remove screws from the M.2 standoffs

5. Insert the SSD into the slot at an angle and push into the slot gently. Once in, lower the SSD and screw it

into the standoff. Repeat the above steps to install a second M.2 SSD.

6. Insert the SSD carrier board into the SSD carrier board slot as shown below

AS6602T AS6604T

19

7. Fasten the SSD carrier board using two screws as shown below.

AS6602T AS6604T

Replacing the Cover

1. Replace the cover and tighten the three screws that were removed previously.

AS6602T AS6604T

2. Reconnect all cables including the power cord and then start up the NAS.

AS6602T AS6604T

20

4. Software Installation Guide

There are 4 different installation methods that you can choose from. You can go to the download section of the

ASUSTOR website (http://www.asustor.com/service/downloads) to download the latest software.

Download Center Installation

Windows Users

1. After ASUSTOR Control Center has been installed, it will automatically begin to scan your network for

ASUSTOR NAS devices.

2. Select your NAS from the list and follow the installation wizard’s instructions to complete the configuration

process.

Page is loading ...

Asustor LOCKERSTOR 2 (AS6602T), AS6602T, AS6604T, LOCKERSTOR 4 (AS6604T) Quick Installation Guide

Related papers

Other documents