CD Recorder
CDR631 387K855010 MIT
3120 785 22410
First Issue 2001.02
Service
Manual CDR631 /F1B, /N1M, /U1B
R
CDR631
Printed in Japan
Please use this service manual with referring to the user guide ( D.F.U. ) without fail.
CD RECORDER CDR631
POWER
IR
STANDBY
Recordable
ReWritable
HEADPHONE LEVEL
010
MENU
DELETE
CANCL
TR.INCR.
REPEATRANDOM
ERASE
TEXT
0
5
9
8
7
4
3
6
12
TIME
REC MODE
STORE
FINAL
REC LEVEL/SELECT
PUSH ENTER
PROG
INPUT
TABLE OF CONTENTS
SECTION PAGE
MAIN UNIT
1. Servicing the CDR631 ............................................................................................................................... 1
2. TECHNICAL SPECIFICATIONS ............................................................................................................... 3
3. WARNINGS .............................................................................................................................................. 4
4. SERVICE HINTS AND TOOLS ................................................................................................................. 5
5. DIAGNOSTIC SOFTWARE ....................................................................................................................... 6
6. FAULTFINDING TREES ......................................................................................................................... 10
7. FAULTFINDING GUIDE .......................................................................................................................... 14
8. WIRING DIAGRAM ................................................................................................................................. 29
9. BLOCK DIAGRAM ................................................................................................................................... 31
10. SCHEMATIC DIAGRAM AND PARTS LOCATION ................................................................................. 33
11. EXPLODED VIEW AND PARTS LIST ..................................................................................................... 43
12. ELECTRICAL PARTS LIST ..................................................................................................................... 46
REMARK : This service manual explains them by extracting specifications
designed for the model CDR631 only. The explanation for CD-R module
"MAR770" (Loader : CDL4009' + CD-R Main board) is not mentioned on this
service manual.
The CD-R module information is described in the service manual of CD-R
modules <MAR770/MAR775>.
MARANTZ DESIGN AND SERVICE
Using superior design and selected high grade components, MARANTZ company has created the ultimate in stereo sound.
Only original MARANTZ parts can insure that your MARANTZ product will continue to perform to the specifications for which
it is famous.
Parts for your MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent.
ORDERING PARTS :
Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specified.
The following information must be supplied to eliminate delays in processing your order :
1. Complete address
2. Complete part numbers and quantities required
3. Description of parts
4. Model number for which part is required
5. Way of shipment
6. Signature : any order form or Fax. must be signed, otherwise such part order will be considered as null and void.
SHOCK, FIRE HAZARD SERVICE TEST :
CAUTION : After servicing this appliance and prior to returning to customer, measure the resistance between either primary AC
cord connector pins ( with unit NOT connected to AC mains and its Power switch ON ), and the face or Front Panel of product and
controls and chassis bottom.
Any resistance measurement less than 1 Megohms should cause unit to be repaired or corrected before AC power is applied, and
verified before it is return to the user/customer.
Ref. UL Standard No. 813.
In case of difficulties, do not hesitate to contact the Technical
Department at above mentioned address.
001120MIT
USA
MARANTZ AMERICA, INC
MARANTZ AMERICA, INC.
440 MEDINAH ROAD
ROSELLE, ILLINOIS 60172
USA
PHONE : 630 - 307 - 3100
FAX : 630 - 307 - 2687
BRAZIL
PHILIPS DA AMAZONIA IND. ELET. ITDA
CENTRO DE INFORMACOES AO
CEP 04698-970
SAO PAULO, SP, BRAZIL
PHONE : 0800 - 123123
(Discagem Direta Gratuita)
FAX : +55 11 534. 8988
JAPAN
Technical
MARANTZ JAPAN, INC.
35- 1, 7- CHOME, SAGAMIONO
SAGAMIHARA - SHI, KANAGAWA
JAPAN 228-8505
PHONE : +81 42 748 1013
FAX : +81 42 741 9190
EUROPE / TRADING
MARANTZ EUROPE B.V.
P.O.BOX 80002, BUILDING SFF2
5600 JB EINDHOVEN
THE NETHERLANDS
PHONE : +31 - 40 - 2732241
FAX : +31 - 40 - 2735578
TECHNICAL AUDIO GROUP PTY, LTD
558 DARLING STREET,
BALMAIN, NSW 2041,
AUSTRALIA
PHONE : 61 - 2 - 9810 - 5300
FAX : 61 - 2 - 9810 - 5355
CANADA
LENBROOK INDUSTRIES LIMITED
633 GRANITE COURT,
PICKERING, ONTARIO L1W 3K1
CANADA
PHONE : 905 - 831 - 6333
FAX : 905 - 831 - 6936
AUSTRALIA
QualiFi Pty Ltd,
24 LIONEL ROAD,
MT. WAVERLEY VIC 3149
AUSTRALIA
PHONE : +61 - (0)3 - 9543 - 1522
FAX : +61 - (0)3 - 9543 - 3677
NEW ZEALAND
WILDASH AUDIO SYSTEMS NZ
14 MALVERN ROAD MT ALBERT
AUCKLAND NEW ZEALAND
PHONE : +64 - 9 - 8451958
FAX : +64 - 9 - 8463554
THAILAND
MRZ STANDARD CO.,LTD
746 - 754 MAHACHAI ROAD.,
WANGBURAPAPIROM, PHRANAKORN,
BANGKOK, 10200 THAILAND
PHONE : +66 - 2 - 222 9181
FAX : +66 - 2 - 224 6795
TAIWAN
PAI- YUING CO., LTD.
6 TH FL NO, 148 SUNG KIANG ROAD,
TAIPEI, 10429, TAIWAN R.O.C.
PHONE : +886 - 2 - 25221304
FAX : +886 - 2 - 25630415
MALAYSIA
WO KEE HONG ELECTRONICS SDN. BHD.
SUITE 8.1, LEVEL 8, MENARA GENESIS,
NO. 33, JALAN SULTAN ISMAIL,
50250 KUALA LUMPUR, MALAYSIA
PHONE : +60 3 - 2457677
FAX : +60 3 - 2458180
AMERICAS
SUPERSCOPE TECHNOLOGIES, INC.
MARANTZ PROFESSIONAL PRODUCTS
2640 WHITE OAK CIRCLE, SUITE A
AURORA, ILLINOIS 60504 USA
PHONE : 630 - 820 - 4800
FAX : 630 - 820 - 8103
AUSTRALIA
KOREA
MK ENTERPRISES LTD.
ROOM 604/605, ELECTRO-OFFICETEL, 16-58,
3GA, HANGANG-RO, YONGSAN-KU, SEOUL
KOREA
PHONE : +822 - 3232 - 155
FAX : +822 - 3232 - 154
SINGAPORE
WO KEE HONG DISTRIBUTION PTE LTD
130 JOO SENG ROAD
#03-02 OLIVINE BUILDING
SINGAPORE 368357
PHONE : +65 858 5535 / +65 381 8621
FAX : +65 858 6078
1
1.Servicing the CDR631
1.1 INTRODUCTION:
The CDR631is the professional version of a CD recorder, this means that the SCMS (Serial Copy Management System) is
not included. The CDR631can record on the Audio and CDRs PC.
The CDR631is suitable for recording and playback of CD-R W discs (CD-Re Writable disc).
1.2 OPENING THE PRODUCT:
The product can be opened by removing the top cover (8 screws). Once the product is opened one can have access to the
several PCB's and the main module. To have access to the Display PCB, the Headphone PCB first the front cover has to
be removed.
Below the several PCB's and it function and service policy will be discussed:
Consumer : For Digital Audio
Professional : For General use (Including PC)
P : Playback
R : Recording
Playback & Recording and Disc
Disc
Player/Recorder
CD
CDR CD-RW
SCMS
Consumer Disc Consumer Disc
Professional Disc Professional Disc
Finalized Finalized
non
Finalized
non
Finalized
non
Finalized
non
Finalized
Finalized Finalized
Audio CD Player
Current products Ex:CD-17
Audio CD Player
CD-RW playback Ex:CD-17MK II
CD-RW Recorder
For Professional Ex:CDR630/631/640
CD-RW Recorder
For Consumer Ex:DR6000/6050
PP no P no no no no no -
PP no P no P no P no -
P P P/R P P/R P/R P/R P/R P/R no
P P P/R PPPP P/R P/R YES
CDR LOADER
SWITCHING POWER
SUPPLY BOARD
AUDIO
BOARD
DISPLAY BOARD
HEAD
PHONE
BOARD
MOTER
BOARD
2
1.2.1 CDR loader (CDR main module CDL4009 or MAR770):
This complete CDR loader is considered as not repairable in the field. therefore this module will be repaired centrally. A
module exchange procedure will be set up for this purpose. The module can be removed from the product by removing 4
screws and the transformer (see demounting the CDR module on page 1-7), and loosing the connectors.
This module is the complete CD recorder, it contains the following parts:
CD Mechanism (CDM4009'). Underneath this mechanism a PCB is mounted which is adjusted to the mechanism (laser
current settings are stored in EEPROM).
Loader Assy. This mechanical assy takes care for the tray control.
Main PCB. This PCB takes care that the (analog or digital) signal to be recorded is converted into a suitable signal which
can be recorded on the disc.
Digital signals with an other sampling frequency then 44.1kHz will be converted in the sample rate converter (DASP) to
44.1kHz.
Analog signals will be first converted into a digital converter by the AD converter.
This PCB also takes care that the signal from the CD (playback) is converted into a suitable digital signal (or analog via
the DA converter).
The main microprocessor controls the several functions of this PCB.
1.2.2 Switching Power Supply Board.
This PCB contains the Power Supply, which delivers the sevelal volteges for the each PCB in the CDR631. On this Power
Supply a fuse (Primaly side) are mounted on this PCB. The power SW is jointed the Power bottom on the front panel.
All parts are available as spare parts.
1.2.3 Audio Board.
This PCB contains the audio part,witch takes care that the signal from CDR main module is converted into an analog signal
via DA converter and outputs the analog signal. This PCB contains the output and input connectors also. All parts are available
as spare parts.
1.2.4 Display Board.
This PCB contains the Display, which informs the user about the status of the recording/playback process and it also takes
care for scanning the keys on the front panel. The information from the keys is fed via a I C connection to the main
microprocessor on the CDR loader module. Information which needs to be displayed is also fed via this I C line from the
main microprocessor on the CDR loader module to the display controller.
The parts for this PCB are available as service parts so this PCB can be repairable up to component level.
1.2.5 Headphone Board.
This PCB contains the headphone socket and potentiometer which controls the headphone volume. All parts are available
as spare parts.
2
2
IMPORTANT
In case of replace the CD-R module "MAR770", the initialization is necessary.
Please initialize the CD-R module with following orders.
1. Press the POWER button (POWER ON) while depressing FINALIZE button and REC
MODE button together.
2. FL Display shows;
WAIT PGM PROTOCOL PGM PORT END
3. Press the POWER button (POWER OFF).
Then the CD-R module set up to CDR631 own status.
3
2 TECHNICAL SPECIFICATIONS
GENERAL
System .................................................................................................... Compact disc digital audio
Number of channels ................................................................................ 2 (stereo)
Applicable discs ...................................................................................... CD, CD-R , CD-RW
Power Requirement
F version ........................................................................................... AC 100 V 50 / 60 Hz
N version ........................................................................................... AC 100 - 240 V 50 /60 Hz
U version. .......................................................................................... AC 120 V 60 Hz
Power Consumption ................................................................................ 19 W
Operating Temperature . ......................................................................... 5 °C - 35 °C
Dimension (MAX)
Width ................................................................................................. 483 mm
Height ................................................................................................ 100 mm
Depth ................................................................................................ 340 mm
Weight ................................................................................................ 4.7 kg
AUDIO
Frequency Response ............................................................................. 20 Hz - 20 kHz
Playback S/N .......................................................................................... 108 dB
Playback Dynamic Range ....................................................................... 95 dB
Playback Total Harmonic Distortion ........................................................ 92 dB
Recording S/N (analog) .......................................................................... 96 dB
Recording Dynamic Range (analog) ....................................................... 92 dB
Recording Total Harmonic Distortion (analog) ........................................ 88 dB
Analog Output Voltage ............................................................................. 2 Vrms
Digital Coaxial Output ............................................................................. 0.5 V (p-p) / 75 ohms
Digital Optical Output .............................................................................. - 20 dB
Headphones ............................................................................................ 0 - 5 Vrms / 8 - 2000 ohms
Recording values for line input
Digital Coaxial Input (automatic sample rate conversion) ....................... 11 - 56 kHz
Digital Optical Input (automatic sample rate conversion) ........................ 11 - 56 kHz
Digital XLR Input (automatic sample rate conversion) ............................ 11 - 56 kHz
Analog Input Sensitivity (Unbalanced) .................................................... 500 mVrms / 50 kohms
Analog Input Sensitivity (Balanced) ........................................................ 0 dBu to +22 dBu / 50 kohms
(default setting : +16 dBu / 50 kohms)
Specifications subject to change without prior notice.
4
WARNING
All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD). Careless handling during
repair can reduce life drastically.
When repairing, make sure that you are connected with the
same potential as the mass of the set via a wristband with
resistance. Keep components and tools at this potential.
ATTENTION
Tous les IC et beaucoup d´autres semi-conducteurs sont
sensibles aux décharges statiques (ESD). Leur longévite
pourrait être considérablement écourtée par le fait qu´aucune
précaution nést prise à leur manipulation.
Lors de réparations, s´assurer de bien être relié au même
potentiel que la masse de l´appareil et enfileer le bracelet
serti d´une résistance de sécurité.
Veiller à ce que les composants ainsi que les outils que l´on
utilise soient également à ce potentiel.
WARNUNG
Alle ICs und viele andere Halbleiter sind empfindlich
gegenüber elektrostatischen Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kann die
Lebensdauer drastisch reduzieren.
Sorgen Sie dafür, daß sie im Reparaturfall über ein Puls-
armband mit Widerstand mit dem Massepotential des
Gerätes verbunden sind.
Halten Sie Bauteile und Hilfsmittel ebenfalls auf diesem
Potential.
WAARSCHUWING
Alle IC´s en vele andere halfgeleiders zijn gevoelig voor
electrostatische ontladingen (ESD).
Onzorgvuldig behandelen tijdens reparatie kan de levensduur
drastisch doen vermindern. Zorg ervoor dat u tijdens reparatie
via een polsband met weerstand verbonden bent met hetzelfde
potentiaal als de massa van het apparaat.
Houd componenten en hulpmiddelen ook op ditzelfde potentiaal.
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono sensibili alle scariche
statiche (ESD).
La loro longevità potrebbe essere fortemente ridatta in caso di
non osservazione della più grande cauzione alla loro
manipolazione. Durante le riparationi occorre quindi essere
collegato allo stesso potenziale che quello della massa
delápparecchio tramite un braccialetto a resistenza.
Assicurarsi che i componenti e anche gli utensili con quali si
lavora siano anche a questo potenziale.
Safety regulations require that the set be restored to its
original condition and that parts which are identical with
those specified be used.
Safety components are marked by the symbol
Le norme di sicurezza estigono che l´apparecchio venga
rimesso nelle condizioni originali e che siano utilizzati i
pezzi di ricambiago identici a quelli specificati.
Componenty di sicurezza sono marcati con
Veiligheidsbepalingen vereisen, dat het apparaat in zijn
oorspronkeliijke toestand wordt teruggebracht en dat
onderdelen, identiek aan de gespecificeerde, worden toegepast.
De Veiligheidsonderdelen zijn aangeduid met het symbool
Varning !
Osynlig laserstrålning när apparaten är öppnad och
spärren är urkopplad. Betrakta ej strålen.
Advarsel !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere
er ude af funktion. Undgå udsaettelse for stråling.
Varoitus !
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen !
ESD
SAFETY
Bei jeder Reparatur sind die geltenden Sicherheitsvor-
schriften zu beachten. Der Originalzustand des Gerätes
darf nicht verändert werden. Für Reparaturen sind Original-
ersatzteile zu verwenden.
Sicherheitsbauteile sind durch das Symbol markiert.
Les normes de sécurité exigent que l`appareil soit remis
à l`état d`origine et que soient utilisées les pièces de
rechange identiques à celles spécifiées.
Les composants de sécurité sont marqués
DANGER: Invisible laser radiation when open.
"Pour votre sécurite, ces documents doivent être utilisés par
des spécialistes agréés, seuls habilités à réparer votre
appareil en panne".
After servicing and before returning the set to customer
perform a leakage current measurement test from all
exposed metal parts to earth ground, to assure no
shock hazard exists.
The leakage current must not exceed 0.5mA.
AVOID DIRECT EXPOSURE TO BEAM.
AVAILABLE ESD PROTECTION EQUIPMENT :
anti-static table mat large 1200x650x1.25mm 4822 466 10953
small 600x650x1.25mm 4822 466 10958
anti-static wristband 4822 395 10223
connection box (3 press stud connections, 1M ) 4822 320 11307
extendible cable (2m, 2M , to connect wristband to connection box) 4822 320 11305
connecting cable (3m, 2M , to connect table mat to connection box) 4822 320 11306
earth cable (1M , to connect any product to mat or to connection box) 4822 320 11308
KIT ESD3 (combining all 6 prior products - small table mat) 4822 310 10671
wristband tester 4822 344 13999
LASER PRODUCT CLASS 3B
U : VERSION N : VERSION
LASER PRODUCT
CLASS III b
3. WARNINGS
5
SERVICE TOOLS
“The tools listed below are standard test tools that can be used for repairing and testing Marantz
CD Players & Recorders. Unless otherwise stated in the text, these tools are not mandatory for
servicing Marantz CD Players & Recorders”
Audio signals disc 4822 397 30184
Disc without errors (SBC444)+
Disc with DO errors, black spots and fingerprints (SBC444A) 4822 397 30245
Disc (65 min 1kHz) without no pause 4822 397 30155
Max. diameter disc (58.0 mm) 4822 397 60141
Torx screwdrivers
Set (straight) 4822 395 50145
Set (square) 4822 395 50132
13th order filter 4822 395 30204
Hexagon socket screw button (No. 1.5)
4. SERVICE HINTS AND TOOLS
6
CDR MAIN
BOARD TEST
ELECTRICAL SERVICE DIAGNOSTICS
(software versions, test for defective components)
PLAYER
INFORMATION
YES
NO
Tests OK?
If power ON,
switch power OFF
Load CD-DA disc (SBC444A)
Press <PLAY> + <F FWD>
simultaneously and switch ON unit
Display :
"PLAYER ID"
"SW VERSION BACK END"
"SW VERSION CDR LOADER"
(DR6050
"SW VERSION CD LOADER"
)
Display :
"DTST1"
DRAM test (7702)
Display :
"DTST2"
FLASH CHECKSUM test (7702)
Display :
"DTST3"
FLASH ERASE test (7702)
Display :
"DTST4" *
CODEC test (7702)
Display :
"DTST5"
CDR LOADER
COMMUNICATION test
Display :
"DTST5"
*
CD LOADER
COMMUNICATION test
PASS OR FAIL
PASS OR FAIL
PASS OR FAIL
PASS OR FAIL
PASS OR FAIL
PASS OR FAIL
Display :
"DERRn"
n = failed test
Display next
failed test
ABORT TEST
Press <F FWD>
ABORT TEST
Press <F FWD>
ABORT TEST
Press <F FWD>
ABORT TEST
Press <F FWD>
ABORT TEST
Press <F FWD>
LOADER TESTS
Display shows current disc time
CDR LOADER TEST
CD-DA disc must be loaded
ABORT TEST
Press <F FWD>
YES
NO
Test OK? Display :
"BERR1"
or
"NO CDDA"
or
"NO DISC"
Display shows current disc time
CD LOADER TEST *
CD-DA disc must be loaded
YES
NO
Test OK? Display :
"BERR2"
or
"NO CDDA"
or
"NO DISC"
* FOR CDR500 ONLY
ABORT TEST
Press <F FWD>
Press <F FWD>
Display segments blink at f=1Hz
DISPLAY TEST
Press <F FWD>
DISPLAY TEST
Press <F FWD>
Display shows name of pressed keys
KEYBOARD & RC TEST
KEYBOARD &
RC TEST
To end test, switch OFF unit
* FOR CDR500 ONLY
5. Diagnostic Software
5.1 Electrical service diagnostics
Figure 5-1
7
5.1.1 Description
The intention of the electrical service diagnostics is to show the
software versions present in the player and to direct the dealer
towards defective internal units. The units are : the CDR main
board, the CDR loader, the CD loader in case of a CDR500 and
the keyboard/display board. A sequence of tests is executed
automatically. Some of the tests can be aborted or skipped
without the result being taken into account. External tools or
disassembly of the unit is not necessary to get the diagnostic
information. Pressing keys [PLAY/PAUSE] and [F FWD]
simultaneously while switching on the unit, starts the test.
Switching off the unit ends the test.
5.1.2 Requirements to perform the test
• Working keyboard to start up the test.
• Working local display to check the output messages.
• A CD-DA disc with a minimum of 3 tracks in all trays to
perform the disc test.
5.1.3 Description of the tests
Player information
In this part of the test the following important information can be
checked without removing the cover :
• Recorder ID.
• SW-version back end of player.
• SW-version CDR loader.
• SW-version CD loader (only for CDR500).
CDR main board test
As soon as the CDR main board tests are finished, all failure
messages (if any) will be displayed sequentially by pressing the
[F FWD] key. The message "DERRn" will be displayed with n
indicating the faulty test number.
If one of the tests is aborted with the [F FWD] key, no error
message will be displayed for this test. The flash data erase
test ("DTST3") can not be aborted !
The CDR main board test consists out of :
DRAM test
Display : "DTST1". The DRAM used for buffer management is
tested by writing, reading and verifying test patterns.
Flash checksum test
Display : "DTST2". This test checks the checksum of the
player's SW stored in the flash.
Flash data erase
Display : "DTST3". During this test, all temporary information
(CDtxt) in the flash is erased.
CODEC (ADC/DAC) test
Display : "DTST4". This test checks the CODEC IC by writing,
reading and verifying test patterns. The test is not applicable for
CDR950.
CDR communication test
Display : "DTST5". The communication between the host
processor (DASP) and the CDR loader via the DSA-R-bus is
tested.
CD communication test
Display : "DTST6"). The communication between the host
processor (DASP) and the CD loader is tested. The test is only
applicable for CDR500.
Loader tests
These tests determine if the CDR loader and the CD loader in
case of a CDR500 work correctly. A CD-DA disc with a
minimum of 3 tracks needs to be inserted in both loaders. A
disc test is executed to check focus control, disc motor control,
radial control and jump grooves control. The disc test is
performed by audio play-back of 5 seconds at the beginning,
middle and end of the disc.
CDR loader test
During the test, the current disc time is shown. In case of an
error the message "BERR1" will be displayed and the [F FWD]
key must be pressed to continue with the following test.
Pressing the [F FWD] key also aborts this test.
CD loader test
For CDR500 only. During the test, the current disc time is
shown. In case of an error the message "BERR2" will be
displayed and the [F FWD] key must be pressed to continue
with the following test. Pressing the [F FWD] key also aborts
this test.
Display test
All segments will blink at a frequency of 1 Hz. Pressing the [F
FWD] key will start the next test because the user has to check
for himself if all segments work properly.
Keyboard and remote control tests
The test will give the user the ability to test every key without
executing the function assigned to it. Therefore, the user needs
to press every key on the keyboard and the remote control. The
display will show the name of the key being pressed. Pressing
more than one key at once will give an unpredictable result
except for the service combinations : [PLAY/PAUSE] + [STOP],
[PLAY/PAUSE] + [ERASE] + [RECORD], [PLAY/PAUSE] +
[RECORD].
8
5.2 Mechanical service diagnostics
Figure 5-2
5.2.1 Description
No external tools are required to perform this test. The cover
needs to be removed because the user has to check the
movements of the tray, focus and sledge visually. Pressing
keys [PLAY/PAUSE] and [STOP] simultaneously while
switching on the unit, starts the test. Switching off the unit ends
the test. In case of a CDR500, one can check the CD loader
mechanics in the same way by pressing the above key
combination on the CD player keys.
5.2.2 Requirements to perform the test
• Working keyboard to cycle through the tests and to start up
the test.
• Working local display to check the output messages.
5.2.3 Description of the tests
Focus control test
The focussing lens is continuously moving up and down. The
display reads "BUSY".
Sledge control test
After pressing [F FWD] the sledge continuously moves up and
down. Pressing [REWIND] stops the sledge at the position it is
in and the focus control test resumes. The display reads
"BUSY".
Tray control test
This test starts from within the focus control test routine.
Pressing [OPEN/CLOSE] moves the tray in or out. In the tray
open position one can initiate focus and sledge tests by
pressing [F FWD]. One has to stop these tests pressing
[REWIND] before it is possible to close the tray again.
Depending on the action the display reads "OPEN",
"OPENED", "CLOSE" or "BUSY".
FOCUS TEST
Display shows
“BUSY”
Visual inspection
TRAY TEST
Visual inspection
Display shows
“OPENED”
even if tray is blocked
<OPEN>
<CLOSE>
SLEDGE TEST
Visual inspection
<FWD><REWIND>
MECHANICAL SERVICE DIAGNOSTICS
(test for defective components)
Press <PLAY/PAUSE> + <STOP>
simultaneously and switch
ON unit
If power ON,
switch power OFF
To end test, switch OFF unit
Display shows
“BUSY”
9
5.3 DC-erase service mode
5.3.1 Description
This test is initiated by pressing [ERASE] and [RECORD]
simultaneously while switching on the unit. The player will
erase a complete CD-RW disc (including PMA and ATIP lead
out area) at speed N=2. The display shows the countdown of
the remaining time required for the operation to complete. The
format is "ER mm:ss", where "mm" are the remaining minutes
and "ss" the remaining seconds. After completion the message
"PASSED" is shown, and the player has to be switched off and
on again to start up in normal operating mode. Switching off the
unit before completion of the test, leaves the disc in an
unpredictable state. In such case only a complete DC-erase
procedure can recover the CD-RW disc.
5.3.2 Requirements to perform the test
• Functional CDR player.
• A CD-RW audio disc must be present in the tray.
Figure 5-3
Load CD-RW disc
Press
<ERASE> + <RECORD>
simultaneously and switch
ON unit
Display shows:
“
PASSED
”
when the erase function is
completed
“
ERROR
”
if DC ERASE fails
Display shows:
“
ER mm:ss
”
mm
:remaining minutes
ss :remaining seconds
TOTAL
and
REM
are also
illuminated
DC ERASE SERVICE MODE
(erasement of complete CD-RW)
To end test, switch OFF unit
10
Figure 6-1
6. Faultfinding Trees
NO DISC LOADED
SWITCH ON POWER
PRESS
<OPEN/CLOSE>
SEE CD-DA DISC
FAULT FINDING
SEE CD-R DISC
FAULT FINDING
SEE CD-RW DISC
FAULT FINDING
INSERT DISC
PRESS <OPEN/CLOSE>
DISPLAY?
DISPLAY:
"INSERT DISC"
CD-DA DISC
LOADED?
CHECK:
•POWER SUPPLY & TRAFO
⇒WIRING
⇒ON/OFF SWITCH
⇒FUSES
⇒VOLTAGES
•DISPLAY (SEE FAULT FINDING GUIDE DISPLAY BOARD)
⇒WIRING
⇒CONTROL SIGNALS
⇒CLOCK SIGNAL 8MHz
⇒SUPPLY VOLTAGES
⇒ELECTRICAL SERVICE DIAGNOSTICS:
DISPLAY TEST, KEYBOARD TEST
•POWER SUPPLY VOLTAGES
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
• MECHANICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF ERROR OCCURS
TRAY?
CD-R DISC
LOADED?
NONO
NO
NO
NO
YES
YESYES
YES
YES
CD-RW DISC
LOADED?
YES
PRESS <DISPLAY>
•MAINS, MAINS CABLE
CHECK:
STANDBY LED
⇒
⇒KEYBOARD
•WIRING
•DISPLAY BOARD (SEE FAULT FINDING GUIDE DISPLAY BOARD)
⇒WIRING
⇒CONTROL SIGNALS
⇒CLOCK SIGNAL 8MHz
⇒SUPPLY VOLTAGES
⇒ELECTRICAL SERVICE DIAGNOSTICS:
DISPLAY TEST, KEYBOARD TEST
⇒KEYBOARD
11
Figure 6-2
PLAY BACK OF CD-DA
DISCS OK
PRESS <PLAY>
CD-DA DISC LOADED
CHECK:
CHECK:
•
NO
NO
NO
NO
NO
YES
YES
YES
YES
HEADPHONE?
DIGITAL
YES
DISTORTION?
DISPLAY:
“CD”
&
T.O.C. INFO?
YES
DISC
DETECTION &
READING?
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
•DISC: DIRT, SCRATCHES, DAMAGED...
NO •POWER SUPPLY VOLTAGES
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
•WIRING
AUDIO BOARD
⇒FLEX & WIRE CONNECTIONS
⇒+5V (pin 4. W855), +12V(pin 2. W855), -12V(pin 6. W855)
AUDIO
ANALOG
OUT?
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
•AUDIO CONNECTIONS & CABLES
•CONNECTION OF HEADPHONE
ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
CHECK SINGNAL
-FOR COAXIAL OUT AT QT31,LT13
-FOR OPTICAL OUT AT QT31,JT21
⇒
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
AUDIO
OUT?
⇒SEE FAULTFINDING GUIDE AUDIO BOARD - ANALOG OUT PATH
•HEADPHONE BOARD
⇒+10V (pin 6. J903), -10V (pin 2. J903)
⇒WIRE CONNECTION
⇒PLAY SBC442 DISC (1kHz, -30dB) AND CHECK SIGNAL AT
Q901
⇒KILL VOLTAGE (pin 1. J903) : -8V DURING PLAY
⇒KILL TRANSISTORS QN01 - QN02
•
•AUDIO BOARD
⇒FLEX & WIRE CONNECTIONS
⇒+5V (pin 3. W853)
•AUDIO CONNECTIONS & CABLES
Faultfinding Trees
12
Figure 6-3
FINALISED OR PARTIALLY
RECORDED CD-R DISC
CD-R DISC EMPTY
START MANUAL
RECORDING FROM
ANALOG SOURCE
CD-R DISC LOADED
LEVEL
ADJUSTABLE?
NO
YES
ANALOG IN?
NO
YES
NO
YES
DISPLAY:
“CD R”
&
OPC INFO?
YES
DISC
DETECTION &
READING?
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
•DISC: DIRT, SCRATCHES, DAMAGED...
NO
•POWER SUPPLY VOLTAGES
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
•WIRING
NO
YES
DISPLAY:
“CD”
OR
“CD R”
&
T.O.C. INFO?
SEE CD-DA DISC
FAULT FINDING
CHECK:
•
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
DISPLAY BOARD (SEE FAULT FINDING GUIDE DISPLAY BOARD)
⇒EASY JOG KNOB
⇒I2C COMMUNICATION
⇒ELECTRICAL SERVICE DIAGNOSTICS:
KEYBOARD TEST
•AUDIO CONNECTIONS & CABLES
LOADED :
•
AUDIO
BOARD (SEE FAULT FINDING GUIDE I/O BOARD - ANALOG IN PATH)
SET OK
DIGITAL IN?
OPTICAL IN?
NO
YES
RECORDING
SUCCESSFUL?
NO
YES
CHECK:
CHECK SINGNAL
-FOR BALANCE IN AT Q326
-FOR UNBALANCE IN AT Q331
-FOR BALANCE & UNBALANCE IN AT Q332
-FOR OPTICAL IN AT J301
•AUDIO CONNECTIONS & CABLES
•AUDIO BOARD
⇒
⇒
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
CHECK SINGNAL
-FOR XLR IN AT Q326
-FOR COAXIAL IN AT Q331
-FOR XLR & COAXIAL IN AT Q332
-FOR OPTICAL IN AT J301
•AUDIO CONNECTIONS & CABLES
•AUDIO BOARD
⇒FLEX AND WIRE CONNECTIONS
⇒
⇒
+10V (QM01), -10V (QM02)
+5V (pin 3 conn. W853)
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
13
CD-RW DISC LOADED
START ERASING OF LAST RECORDED TRACK
SET OK
ERASING
SUCCESSFUL?
YES
NO
NO
YES
DISPLAY:
“CD RW”
&
OPC INFO?
YES
DISC
DETECTION &
READING?
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
•DISC: DIRT, SCRATCHES, DAMAGED...
NO
•POWER SUPPLY VOLTAGES
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
CHECK:
•WIRING
NO
YES
CHECK:
•ELECTRICAL SERVICE DIAGNOSTICS:
REPLACE CDR MODULE IF
"DERRn"
OR
"BERRn"
ERROR OCCURS
•IF DISC CORRUPTED TRY DC ERASE
DISPLAY:
“CD”
OR
“CD RW”
&
T.O.C. INFO?
CD-RW DISC EMPTY FINALISED OR PARTIALLY
RECORDED CD-RW DISC
SEE CD-DA DISC
FAULT FINDING
LOADED :
Figure 6-4
14
651516
26
27
28
29
30
31
32
34
35
36
37
41
141211 17 18 20 21 22
42434445464748495051
10
25
23 244
74
73
72
71
70
69
68
67
66
65
3
64 63 62 61 60 59 58 57 56 55
2
54 53
1
80
79
77
76
75
13
39
38
40
78
79819
33
52
TMP87C874F
SCL
SDA
VSS1
XOUT
XIN
RESETN
P22
P21
TEST1
P20
INT0
INT1
SCK0
PORT3
I C
2
VKK
COUNTER
PROGRAM
I/O PORT1
TIMER/COUNTER
I/O PORT6 (VFT)
VASS
VAREF
VDD
I/O PORT8 (VFT)
CONVERT.
8 BIT A/D
16 BIT
( RAM )
512X8 BIT
DATA MEMORY
TIMER/COUNTER
( ROM )
8kX8 BIT
INTERRUPT
CONTROLLER
I/O PORT7 (VFT)
( I/O PORT2 )
PROGR MEMORY
I/O PORT0
CLOCK/TIMING CONTROLLER
8 BIT
I/O PORTD (VFT) I/O PORT9 (VFT)
I/O PORT5
I/O PORT4
C P U
INT0 external interrupt input 0
INT1 external interrupt input 1
RESETN reset signal input, active low
SCL I2C-bus serial clock input/output
SDA I2C-bus serial data input/output
TEST test pin, tied to low
VAREF analog reference voltage input
VASS analog reference ground
VDD +5V
VKK VFT driver power supply
VSS ground
XIN, XOUT resonator connecting pins for high-frequency clock
BLOCK DIAGRAM
PIN DESCRIPTIONS
Display controller TMP87CH74F
TMP87CH74F (QY01) is a high speed and high performance
8-bit single chip microprocessor, containing 8-bit A/D
conversion inputs and a VFT (Vacuum Fluorescent Tube)
driver.
In this application, its functions are :
• slave microprocessor.
• FTD driver.
• generates the square wave for the filament voltage
required for an AC FTD.
• generates the grid and segment scanning for the FTD.
• generates the scanning grid for the key matrix.
• input for remote control.
All the communication runs via the serial bus interface I2C. The
display controller uses an 8Mhz resonator as clock driver.
General description
The display board has three major parts : the FTD (Fluorescent
Tube Display), the display controller TMP87CH74F and the
keyboard. The display controller is controlled by the DASP
master processor on the CDR main board. The communication
protocol used is I2C. So all the information between DASP and
display controller goes via the SDA or I2C DATA and SCL or
I2C CLK lines. Communication is always initiated by the DASP
on the CDR main board. Unlike the previous generations of
CDR players, the interrupt generated by the display controller
at key-press or reception of remote control is not used. Instead,
the DASP polls the display controller for these events.
7. Faultfinding Guide
7.1 Display Board
7.1.1 Description of display board
Figure 7-1
15
PM3392A
CH1!10.0 V= MTB1.00ms ch1+
0V
+4V
-34V
PM3392A
CH1!2.00 V=
CH2 2 V= MTB10.0ms ch1+
+5V
0V
+5V
0V
I2C DATA
I2C CLK
PM3392A
CH1!10.0 V= MTB1.00ms ch1+
0V
+5V
-34V
Supply voltages
The display board receives several voltages via connector
JY01.
• VFTD : -34V ±5% measured at pin 2 of conn. JY52.
• VDC1-VDC2 : 4V1 ±10% measured between pin 1 and 3 of
conn. JY52.
• +5V : + 5V ±5% measured at pin 10 of conn. JY52.
Voltages VFTD, VDC1 and VDC2 are produced in the Switching
Power Supply Board and sent to the display board via the CDR
main board. The +5V voltage is produced on the CDR main
board as D5V.
Clock signal
As clock driver for the display controller, a resonator of 8 Mhz
(XY01) is used. The signal can be measured at pins 8 and 9 of
the display controller : 8 Mhz ±5%.
Control signals
RESETN
The reset signal comes via pin 4 of conn. JY52 from the DASP
master processor on the CDR main board (SYS_RESET). The
reset is low active. It should be kept low during power up for at
least 3 machine cycles with supply voltage in operating range
and a stable clock signal (1 machine cycle = 12 x 1/Fc (8 Mhz)
sec.). During normal operation, the reset should be high (3V3).
The high signal is 3V3 because the DASP operates on 3V3.
I2C DATA/I2C CLK
These lines connect to the DASP master processor via
respectively pin 5 and pin 7 of conn. JY52. When there is
no communication, they should have the high level (+5V). The
oscillogram below gives an indication of how these signals
should look like.
Grid lines
Level and timing of all grid lines, G1-->G15, can be checked
either at the FTD itself or at the display controller. Grid lines
G13, G14 and G15 each have an extra current amplifier in line
: QY04 for G13, QY03 for G14 and QY02 for G15. A typical
grid line signal shows in the oscillogram below.
Segment lines
Level and timing of all segment lines, P-->P21, can be
checked either at the FTD itself or atthe display controller.
The data on these segment lines however, depends on the
characters displayed. The oscillogram below shows a
segment line with data. A segment line without data
maintains a -30V level.
FTD drive lines
Filament voltage
Should measure 4.3V ±10% (=VDC1-VDC2) between pins 1-2
and pins 52-53 of FTD(VY01).
7.1.2 Test instructions
Figure 7-2 “I2C SIGNALS”
Figure 7-3 “OSD”
Figure 7-4 “SEGMENT LINE”
16
PM3392A
CH1!2.00 V= MTB5.00ms ch1+
0V
+5V
CL 96532121_031.eps
141099
PM3392
Pin3
Pin1
CH1 5.00 V=
CH2 5.00 V= MTB20.0ms- 1.92dv ch2-
CL 96532121_032.eps
141099
PM3392
Pin3
Pin1
CH1 5.00 V=
CH2 5.00 V= M TB20.0ms- 1.92dv ch2-
CL 96532121_033.eps
141099
PM3392A
CH1!2.00 V= MTB20.0ms ch1+
1
+5V
0V
CL 96532121_034.eps
141099
Key matrix lines
The lines connected to pins 18, 19, 20, 34, 35, 36 and 37 of the
display controller act as matrix scanners. Without a key pressed,
they maintain a low level. As soon as a key is pressed, the
scanning line connected to that key puts out a scanning signal,
which should look like the oscillogram below. This scanning signal
goes via the pressed key to I/O port 7 of the display controller
(pins 28 to 33). The display controller can now determine which
key has been pressed. Without a key pressed, pins 28 to 33 of
the display controller maintain a high level (+5V).
Easy jog knob
Rotary operation
The easy jog knob (SY26) incorporates a whole heap of user
control possibilities in just one knob. Without the knob being
operated, pin 1 and 3 of the knob (and thus pin 16 and 17 of the
display controller), maintain the +5V level. Turning the knob
clockwise briefly connects pin 1 to GND followed by pin 3.
The pulses created this way arrive at pin 16 and 17 of the
display controller. The first pulse to arrive tells the controller the
direction of the rotation. Counting the pulses reveals the
amount of rotation. Combining and decoding this information,
the display controller will execute the appropriate task.
Push button operation
This button connects to the key matrix lines and thus the
operation is identical to the ordinary keys. Without being
pressed, pin 4 of the easy jog maintains the low level, pin 5 the
high level. When pressed the scanning signal goes through the
closed contact of pins 4 and 5, and can be checked at both
pins.
IR receiver - remote control
In the CDR631 the IR receiver ZY01 is mounted on the IR board.
In all versions the IR receiver connects to the display controller.
The signal coming from the receiver can be checked at pin 22 of
the display controller. This signal is normally high (+5V).
When the remote control is being operated, pulses mixed in with
the +5V can be measured. The oscillogram gives an indication of
how the signal looks like with the RC being operated.
Figure 7-7 TURN ANTI-CLOCKWISE
Figure 7-6 TURN CLOCKWISE
Figure 7-5 KEY MATRIX SCAN LINE
Figure 7-8 IR RECEIVER SIGNAL
Turning the knob anti-clockwise briefly connects pin 3 to GND
followed by pin 1.
17
SWITCH POWER ON,
EXIT STAND BY
MODE
DISPLAY BOARD
OK
DISPLAY?
CHECK :
• SUPPLY VOLTAGES
⇒ -34V ±5% at conn. JY52-2
⇒ 4V3 ± 10% between conn. JY52-1 and JY52-3
⇒ +5V ± 5 % at conn. JY52-10
• CLOCK SIGNAL
⇒ 8Mhz at pins 8, 9 of QY01
• CONTROL SIGNALS
⇒ RESETN 3V3 (high) at conn.JY52-4 after start up
⇒ I2C DATA at conn. JY52-5
⇒ I2C CLK at conn. JY52-7
• FTD DRIVE LINES
⇒ Filament voltage 4V3 ± 10% between pins 1-2 and
pins 52-53 of the FTD (VY01)
⇒ Grid lines (see test instructions)
⇒ Segment lines (see test instructions)
• ELECTRICAL SERVICE DIAGNOSTICS - Local display test
YES
YES
YES
KEY
FUNCTIONS?
REMOTE
CONTROL?
NO
NO CHECK:
• KEY MATRIX LINES (see test instructions)
• ELECTRICAL SERVICE DIAGNOSTICS – Keyboard test
• EASY JOG KNOB (see test instructions)
NO CHECK:
• IR RECEIVER signal at pin 22 of QY01
• ELECTRICAL SERVICE DIAGNOSTICS – Remote control test
7.1.3 Display board troubleshooting guide
Figure 7-9
18
Voltage
Reference
Modulator
∆ Σ
Modulator
∆ Σ
Digital Decimation
Filter
Serial Output
Interface
Clock Divider
5 4 2 13 24 22 17 15 23 18 19 20
21
3
6
7
1
2
VREF
AINL+
AINL -
AINR+
AINR -
AGND VA VD DGND VB CMODE MCLK SMODE2 SCLK LRCK FSYNC
SDATA
SMODE1
PD HPFE TST1 TST2 TST3 TST4
16 9 8 10 11 14
Test pin Should be left floating. (Pull- down pin)
No. Pin Name I/O PIN / FUNCTION
1 AINR+ IRight channel analog positive input pin
2 AINR- IRight channel analog negative input pin
3 VREF OVoltage Reference output pin (VA-2.6V)
Normally connected to VA with a 0.1uF ceramic capacitor in
parallel with a 10uF electrolytic capacitor.
4 VA Analog section Analog Power Supply, +5V
5 AGND Analog section Analog Ground
6 AlNL+ ILeft channel analog positive input pin
7 AINL- ILeft channel analog negative input pin
8 TST1
Test pin Should be left floating. (Pull- down pin)
Test pin Should be left floating. (Pull- down pin)
Test pin Should be left floating. (Pull- down pin)
10 TST2
11 TST3
14 TST4
9 HPFE IHigh Pass Filter Enable pin (Pull- up pin)
"H": ON
"H": OFF
12 VD Digital section Digital Power Supply pin, +5V
13 DGND Digital section Digital Ground pin
16 PD IPower Down pin
"L" brings the device into power-down mode. Must be done
once after power-on.
17 MCLK I Master Clock input pin
CMODE="H" : 384fs
CMODE="L" : 256fs
18 SCLK I/O Serial Data Clock pin
Data is clocked out at the falling edge of SCLK.
Slave mode: 64fs clock is input usually.
Master mode: SCLK outputs a 64fs clock.
SCLK stays low during the power-down mode(PD="L").
19 LRCK I/O L/R Channel Clock Select pin
Slave mode: An fs clock is fed to this LRCK pin.
Master mode: LRCK output an fs clock.
LRCK goes "H" at SMODE2="L" and "L" at SMODE2="H"
during reset when SMODE1 "H".
20 FSYNC I/O Frame Synchronization Signal pin
S!ave mode: When "H", data bits are clocked out on SDATA.
As I
2
S slave mode ignores FSYNC It should hold "L" or
"H".
Master mode: FSYNC outputs 2fs clock.
Stay low during the power-down mode(PD="L") .
21 SDATA O Serial Data Output pin
Data are output with MSB first, in 2's complement format.
After 20 bits are output it turns to "L". It also remains "L" at a
power- down mode(PD="L").
22 CMODE I Master Clock Selection pin
"L": MCLK=256fs
"H": MCLK=384fs
23 SMODE1 I Serial Interface Mode Select pin
15 SMODE2 I Defines the directions of LRCK, SCLK and FSYNC pins and
Output Data Format. SMODE2 is pull- down pin.
SMODE1 SMODE2 MODE LRCK
L L Slave mode: MSB justified : H/L
H L Master mode Similar to I
2
S : H/L
L H Slave mode: I
2
S : L/H
H H Master mode: I
2
S : L/H
24 VB Substrate Power Supply, +5V
The Audio board for the CDR631 is a full high performance
AD/DA panel, acting as an interface to the outside world. Key
components are DS1807, ADC AK5351 and DAC AK4393.
Description
The via BALANCE in connected anolog-in L and R signals are
pre-amplified by opamp Q761-Q763, and the via UNBALANCE
in connected anolog-in L and R signals are pre-amplified by
opamp Q705, Q706, these signals is selected by Analog SW
Q701 after which they are presented to an adjustable amplifier
made out of DS1807 and opamp Q703 - Q708. The level of the
incoming. Analog signal is adjusted by means of control lines
"I2C" coming from the DASP on the CDR main board and
switching the mux/demux. The anolog signal is then presented
to the A/D converter A5351 (QA01) where they are converted
from analog to I2S-bus data format. The I2S-bus is connected
via connector J601 and flex to the DASP on the CDR main
board. The ADC uses the CL11-clock (11.2896 MHz), coming
from the DASP on the CDR main board.
ADC AK5351
Description
The AK5351 is a stereo, 20-bit oversampling ADC based on
Sigma Delta technology intended primarily for digital audio
bandwith applications. It supports the I2S-bus data format. The
device can be used in either slave or master mode. In this
application it is used in slave mode receiving it's clock from the
DASP on the CDR main board.
Block diagram
7.2 Audio Board
7.2.1 Analog-in path
Figure 7-10
Figure 7-11
Pin description
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
