Maytag MDE17CS Installation guide

Brand: Maytag

Model: MDE17CS

Category: Electric laundry dryers

Type: Installation guide

COMMERCIAL DRYER iNSTALLATiON iNSTRUCTiONS

Electric

iNSTRUCTiONS D'INSTALLATIOND'UN SECHE-LINGE COMMERCIAL

Eiectrique

INSTRUCCIONES DE INSTALACION -SECADORA COMERCIAL

El_ctrica

ISTRUZION! D'INSTALLAZIONE- ASCIUGATRICE COMMERCIALE

Elettrica

MDE17MN MDE17CS

W10297242A

www.maytagcommerciaNaundry.com

TABLEOF CONTENTS

DRYER SAFETY ............................................................................ 3

DRYER DISPOSAL ...................................................................... 3

INSTALLATION REQUIREMENTS .............................................. 4

Tools and Parts .......................................................................... 4

Location Requirements .............................................................. 4

Electrical Requirements ............................................................ 5

Venting Requirements .............................................................. 6

INSTALLATION INSTRUCTIONS - ELECTRIC DRYER .......... 7

Install Leveling Legs.................................................................... 7

Electrical Connection .................................................................. 8

Connect Vent .............................................................................. 8

Complete Installation ................................................................ 8

MAINTENANCE iNSTRUCTiONS ............................................. 8

WARRANTY ................................................................................ 9

TABLEDESMATIERES

SECURITE DU SECHE=LJNGE ................................................ 10

ELIMINATION DU SECHE-UNGE .......................................... 10

EXIGENCES DqNSTALLATJON ................................................ 11

Outillage et pi_ces .................................................................... 11

Exigences d'emplacement ...................................................... 11

Specifications electriques ....................................................... 12

E×igences concernant revacuation .......................................... 13

INSTRUCTIONS D'INSTALLATION - SECHE=LINGE

ELECTRIQUE ............................................................................ 15

Installation des pieds de nivetlement ........................................ 15

Raccordement electrique ........................................................ 15

Raccordement du conduit d'evacuation ................................ 15

Achever I'instatlation ................................................................ 15

INSTRUCTIONS D'ENTRETJEN ............................................... 16

GARANTJE ................................................................................ 17

INDICE

SEGURIDAD DE LA SECADORA ............................................ 18

ELIM_NACI6N DE LA LAVADORA ............................................ 18

REQUISITOS DE INSTALACION ............................................ 19

Piezas y herramientas .......................................................... 19

Requisitos de ubicaci6n ........................................................ 19

Requisitos electricos ............................................................ 20

Requisitos de ventilaci6n .................................................... 21

INSTRUCCIONES DE INSTALACION -

SECADORA ELI=CTRICA ........................................................ 22

Instalaci6n de las paras niveladoras .................................... 22

Conexi6n electrica ................................................................ 23

Cone×i6n det ducto de escape ............................................ 23

Complete la instataci6n ........................................................ 23

INSTRUCCIONES DE MANTENIMIENTO ............................. 23

GARANTJA ................................................................................ 24

INDICE

SICUREZZA DELL'ASCJUGATRICE ........................................ 25

L'EUMJNAZIONE DELL'ASCIUGATRICE .................................. 25

REQUISITI D'INSTALLAZJONE ................................................ 26

Attrezzi e componenti .............................................................. 26

Requisiti di ubicazione ............................................................ 26

Requisiti elettrici ...................................................................... 27

Requisiti di scarico .................................................................. 28

ISTRUZIONI D'INSTALLAZIONE - ASCIUGATRICE

ELETTRICA ............................................................................ 29

Instatlazione dei piedini di regolazione .................................... 29

Connessione elettrica .............................................................. 30

Connessione detlo scarico ...................................................... 30

Comptetamento delt'instattazione ............................................ 30

ISTRUZIONI DI MANUTENZIONE ......................................... 30

GARANZIA .................................................................................. 31

DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

FOR YOUR SAFETY

1. Do not use or store petrol or other flammable materials in this appliance or near this appliance.

2. Do not spray aerosols in the vicinity of this appliance while it is in operation.

3. Do not modify this appliance.

DRYERDISPOSAL

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment

(WEEE).

By ensuring this product is disposed of correctly, you will help avoid potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated

as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and

electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your

household waste disposal service or the shop where you purchased the product.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listed here.

Tools needed:

[] 200 mm (8") or 250 mm [] 8 mm (5_6")socket wrench

(10") Pipe wrench [] Utility knife

[] 200 mm (8") or 250 mm [] Vent clamps

(10") Adjustable wrench

[] Caulk gun and caulk

[] Flat-blade screwdriver (for installing new

[] Phillips screwdriver exhaust vent)

[] Adjustable wrench that [] Pliers

opens to 25 mm (1") or [] Stiff-bladed putty knife

hex-head socket wrench

[] Level

Parts supplied:

Remove parts bag from dryer drum. Check that all parts were

included.

[] Foot boot (4)

[] Dryer foot (4)

NOTE: The circuit diagram for this dryer is located inside the

lower front panel.

Technical

Specifications:

220 - 240 V,50 Hz. AC

Clothes Capacity:

9 Kg Max.

Explosion Hazard

Keep flammable materials and vapors, such as petrol,

away from dryer.

Do not install in a garage.

Failure to do so can result in death, explosion, or fire,

IMPORTANT: Observe all governing codes and ordinances.

[] Check code requirements: Some codes limit or do not permit

installation of clothes dryers in garages, closets, or sleeping

quarters. Contact your local building inspector.

NOTE: The dryer must not be installed in an area where it will be

exposed to water and/or weather.

Recessed Area and Closet Installation instructions

This dryer may be installed in a recessed area or closet. This

dryer must not be installed behind a Iockable door, a sliding door,

or a door with a hinge on the opposite side to that on the dryer.

The installation spacing is in mm and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

If installed in a closet with a door, the minimum unobstructed air

opening in the top and bottom is required. Louvered doors

with equivalent air openings are acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same

closet as the dryer.

Minimum Installation Clearances

o{o

381 mm

(15")*

Inl I

o mm(o")

Recessed front

0mm(0")

view

356 mm --

(14") max.

Closet

door

r--

0 m_

(0")

{_r----25 mm(1")

Closet side view

* Additional clearances for wall, door, and floor moldings may be required

or if external exhaust elbow is used.

310 cm2

(48 in_.)*

Front

View

O closet

door

76 mm (3")

* Opening is the minimum for

a closet door. Louvered doors

with equivalent air openings

are acceptable.

76 mm (3")

Product Dimensions 686 mm (27") dryer

_----686 mm (27")

m--m I

ELECTRIC "_q_----_

I 343 mm

(131/2'')

BACK VIEW

349 mm

,, 102mm(4")

_l dia.

i,/

743 mm (291A'')

673 mm (261/2'')

I .... I

SIDE VIEW

889mm

(35")

25 mm

(1")

........ i

892 mm

(351/s'')

73 mm

(27/8'')

:=m=_m

This dryer is supplied without an electric cord and plug. It

must be connected by a competent electrician to a single-phase

electricity supply at the voltage shown on the dataptate, using

a suitable fixed wiring installation in accordance with local and

national wiring regulations.

[] A 3-wire circular cord of minimum conductor size 2.5 mm2

cross-section area should be used.

[] A 30A supply fuse should be used, and a switch having

a contact separation in both poles that provides full

disconnection under over-voltage category Ill conditions must

be incorporated into the fixed wiring in accordance with local

wiring regulations. The dryer should be positioned so that the

disconnection switch is easily accessible to the user.

[] A cord clamp bush is provided on the dryer, and should

be tightened on completion of wiring. The electrical mains

terminals are located behind the small rear access panel

(terminal block cover), and connections should be made

in accordance with the terminal markings. Remember to

replace the terminal access panel (terminal block cover).

NOTE: In accordance with the European EMC Directive

(2004/108/EC), the maximum electricity supply system

impedance to which the electric dryer should be connected

is declared to be 0.302 Ohm + j0.189 Ohm.

Electric Shock Hazard

Electric earthing is required on this dryer.

Do not earth to a gas pipe.

Do not have a fuse in the neutral or earthing circuit.

Check with a qualified electrician to be sure the dryer is

properly earthed.

Failure to follow these instructions could result in

death, fire, or serious injury.

If codes permit and an additional earth bond wire is used, it is

recommended that a qualified electrician determine that the earth

bond path is adequate.

AUSTRALIA ONLY

For Australia, each single electric dryer is fitted with a cord

and plug, with conductors of 2.5 mm2cross sectional area,

and should be plugged into a suitable electrical socket at the

voltage shown on the dataptate. Do not use extension lead

assemblies on commercial installations. If the supply cord is

damaged, it must be replaced with a specially terminated cord

by an authorized service agent or a similarly qualified person in

order to avoid a hazard. Each electric dryer for other countries

is supplied without an electric cord and plug.

Recommended Earthing Method

[] It is your responsibility to contact a qualified electrical installer

to ensure that the electrical installation is adequate and in

conformance with all local codes and ordinances.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

[] Adequate ventilation has to be provided to avoid the backflow

of gases into the room from appliances burning other fuels,

including open fires (i.e. available airflow into the room should

match airflow out from the room).

[] The dryer vent must not be discharged into a flue which is

used for exhausting fumes from appliances burning gas or

other fuels, chimney, wall, ceiling, or a concealed space of

a building, or any other vent used for venting.

[] Do not use an exhaust hood with a magnetic latch.

[] Do not install flexible metal vent in enclosed walls, ceilings,

or floors.

[] 102 mm (4") heavy metal vent and clamps must be used.

[] Use clamps to seat all joints. Vent must not be connected

or secured with screws or other fastening devices which

extend into the interior of the vent. Do not use duct tape.

IMPORTANT: Observe all governing codes and ordinances.

Use a heavy metal vent. Do not use plastic or metal foil vent.

Rigid metal vent is recommended to avoid crushing

and kinking.

Flexible metal vent must be fully extended and supported when

the dryer is in its final position. Remove excess flexible metal vent

to avoid sagging and kinking that will result in reduced airflow

and poor performance.

An exhaust hood should cap the vent to keep rodents

and insects from entering the building.

Exhaust hood must be at least 305 mm (12") from the ground

or any object that may be in the path of the exhaust (such as

flowers, rocks, or bushes).

If using an existing vent system, clean lint from the entire length

of the system and make sure exhaust hood is not plugged with

lint. Replace any plastic or metal foil vent with rigid metal or

flexible metal vent.

Plan installation to use the fewest number of elbows and turns.

ExhaustAir Flow

A. Good

B.Better

Allow as much room as possible when using elbows or making

turns. Bend vent gradually to avoid kinking.

Vent outlet is located at the center of the bottom dryer back.

The vent can be routed up, down, left, right, behind the dryer,

or straight out the back of the dryer.

Vent System Length

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

Maximum Vent Length

102 mm (4") Exhaust Hoods

Box Louvered Angled

Rigid Metal Vent (_ (_

No. of 900 turns Box Hood and Louvered Style Angled Hood Style

0 19.5m(64ft.) 17.7m (58ft.)

1 16.5m(54ft.) 14.6m (48ft.)

2 13.4m(44ft.) 11.6m (38ft.)

3 10.7 m (35 ft.) 8.8 m (29 ft.)

4 8.2 m (27 ft.) 6.4 m (21 ft.)

If dryer is installed in a confined area, such as a bedroom,

bathroom, or closet, provision must be made for enough air

for combustion and ventilation. (Check governing codes and

ordinances.) See "Recessed Area and Closet Installation

Instructions" in the "Location requirements" section.

A 102 mm (4") outlet hood is preferred. However, a 64 mm

(21/_'') outlet exhaust hood may be used. A 64 mm (2W')

outlet creates greater back pressure than other hood types.

For permanent installation, a stationary vent system is required.

Multiple Dryer Venting

[] A main vent can be used for venting a group of dryers. Main

vent should be sized to remove 5663 I/min (200 CFM) of air

per dryer. Large-capacity lint screens of proper design may be

used inthe main vent if checked and cleaned frequently. The

room where the dryers are located should have make-up air

equal to or greater than the airflow of all the dryers in the

room.

[] A back-draft damper kit is needed and is available from a

commercial laundry distributor; it should be installed in the

vent of each dryer to keep exhausted air from returning into

the dryers and to keep the exhaust in balance within the

main vent. Unobstructed return air openings are required.

Eachventshouldenterthemainventatananglepointinginthe

directionoftheairflow.Ventsenteringfromtheoppositeside

shouldbestaggeredtoreducetheexhaustedairfrominterfering

withtheothervents.

Themaximumangleofeachvententeringthemainventshould

benomorethan30°.

___A.................. 30°max.

( (S :

A. Individual dryer vent

B. Main vent

Keep air openings free of dry cleaning fluid fumes. Fumes create

acids which, when drawn through the dryer heating units, can

damage dryers and items being dried.

A clean-out cover should be located on the main vent for periodic

cleaning of the vent system.

If an exhaust hood cannot be used:

Min. 300 mm (12 I') clearance

above any accumulation

of snow, ice, or debris such

as leaves.

A. Exhaust hood or elbow

B. Waft

C. Main collector vent

D. Horizontal vent

E. 180° sweep elbow

E Vertical vent

G. Roof

610 mm(24_')

min. above

highestpoint

of building

The outside end of the main vent should have a sweep elbow

directed downward. If the main vent travels vertically through the

roof, rather than through the wall, install a 180 ° sweep elbow on

the end of the vent at least 610 mm (24") above the highest part

of the building. The opening in wall or roof shall have a diameter

13 mm (1_,)larger than the vent diameter. The vent should be

centered in the opening.

Do not install screening or cap over the end of the vent.

INSTALLATIONINSTRUCTIONS-ELECTRICDRYER

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

NOTE: Slide dryer onto cardboard or hardboard before moving

to avoid damaging floor covering.

1. Using two or more people, move dryer to desired installation

location.

2. Take tape off front corners of dryer. Open dryer and remove

the literature and parts packages. Wipe the interior of the

drum thoroughly with a damp cloth.

3. Take two of the cardboard corners from the carton and place

them on the floor in back of the dryer. Firmly grasp the body

of the dryer and gently lay it on its back on the cardboard

corners.

4. With one of the legs in hand, check the ridges for a diamond

marking. That's how far the leg is supposed to go into the

hole.

5. Start to screw the leveling legs into the holes by hand. (Use

a small amount of liquid detergent to lubricate the screw

threads so it is easier to turn the legs.) Use a 1" (25 mm)

wrench or socket wrench to finish turning the legs until you

reach the diamond mark. Then fit a protective foot boot over

each foot.

Now stand the dryer up.

6. Remove cardboard or hardboard from under dryer. Adjust the

legs of the dryer up or down until the dryer is level.

Electric Shock Hazard

This dryer must be earthed.

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electric shock.

This is a 3-wire dryer which must be earthed.

This dryer is supplied without an electric cord and plug; it must

be connected by a competent electrician.

In Australia, each single electric dryer is fitted with a cord and

plug. See "Electrical Requirements."

1. Using a 102 mm (4") clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured

to exhaust hood with a 102 mm (4") clamp.

2. Move dryer into final position. Do not crush or kink vent.

Make sure dryer is level.

1. With dryer in final position, place level on top of the dryer, first

side to side; then front to back. If the dryer is not level, adjust

the legs of the dryer up or down until the dryer is level.

2. Switch on power supply.

3. Check dryer operation (some accumulated time may be on

the timer due to factory testing).

Insert coins in slide and press slide in slowly. (Operating time

will accumulate per number of coins and type of timing cam

used.) Push START/RESTART button. Using a full heat cycle

(not the air cycle), let the dryer run for at least five minutes.

Dryer will stop when time is used up.

NOTI=: Dryer door must be closed for dryer to operate. When

door is open, dryer stops, but timer continues to run. To

restart dryer, close door and push START/RESTART button.

4. If drying time is too long, make sure lint screen is clean.

5. Now start the dryer and allow it to complete a full heat cycle

(not air cycle) to make sure it is working properly.

MAINTENANCEINSTRUCTIONS

Maintenance instructions:

[] Clean lint screen after each cycle.

[] Removing accumulated lint:

• From inside the dryer cabinet:

Lint should be removed every 2 years or more often,

depending on dryer usage. Cleaning should be done by a

qualified person.

• From the exhaust vent:

Lint should be removed every 2 years, or more often,

depending on dryer usage.

If dryer does not operate check the following:

[] Electric supply is connected.

[] Circuit breaker is not tripped or fuse is not blown.

[] Door is closed.

[] Controls are set in a running or "ON" position.

[] START button has been pushed firmly.

If you need assistance:

Contact your authorized Maytag Commercial Laundry distributor.

When you call, you will need the dryer model number and serial

number. Both numbers can be found on the serial-rating plate

located on your appliance. Or visit:

www. MaytagCommercialLau ndry.com.

MAYTAG COMMERCIAL WASHE DRYER,STACKED DRYER/

DRYEP COMMERCIAL STACK LAUNDRY, AND MULTi-LOAD

COiN OPERATED COMMERCIAL WASHERS AND DRYERS

WAR NTY

LiMiTED WARRANTY ON PARTS

For the first five years from the date of purchase, when this commercial appliance is installed, maintained and operated according to the

instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation (thereafter "Maytag") will pay for factory

specified parts or original equipment manufacturer parts to correct defects in materials or workmanship. Proof of original purchase date

is required to obtain service under this warranty.

ITEMS MAYTAG WILL NOT PAY FOR

1. All other costs including labor, transportation, or custom duties.

2. Service calls to correct the installation of your commercial appliance, to instruct you how to use your commercial appliance, to

replace or repair fuses, or to correct external wiring or plumbing.

3. Repairs when your commercial appliance is used for other than normal, commercial use.

4. Damage resulting from improper handling of product during delivery, theft, accident, alteration, misuse, abuse, fire, flood, acts of

God, improper installation, installation not in accordance with local electrical or plumbing codes, or use of products not approved

by Maytag.

5. Pickup and Delivery. This commercial appliance is designed to be repaired on location.

6. Repairs to parts or systems resulting from unauthorized modifications made to the commercial appliance.

7. The removal and reinstallation of your commercial appliance if it is installed in an inaccessible location or is not installed in

accordance with published installation instructions.

8. Chemical damage is excluded from all warranty coverage.

9. Changes to the building, room, or location needed in order to make the commercial appliance operate correctly.

DiSCLAiMER OF iMPLiED WARRANTIES; LiMiTATiONS OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THiS LiMiTED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. iMPLiED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABiLiTY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LiMiTATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If you need service, please contact your authorized Maytag Commercial Laundry distributor. To locate your authorized Maytag

Commercial Laundry distributor, or for web inquiries, visit www.MaytagCommercialLaundry.com.

9/07

For written correspondence:

Maytag Commercial Laundry Service Department

2000 M-63 North

Benton Harbor, Michigan 49085 USA

Page is loading ...

GARANTIE DE LAVEUSE, SECHEUSE, LAVEUSE ET

SECHEUSE SUPERPOSEESA USAGE COMMERCIAL,

ENSEMBLE DE BUANDERIE SUPERPOSE A USAGE

p %

COMMERCIAL, ET LAVEUSES ET SECHEUSES A CHARGE

MULTIPLE El A USAGE COMMERCIAL PAYANTES

GARANTIE LIM_TEE SUR LES PI#CES

Pendant les cinq premieres annees _ compter de la date d'achat, Iorsque cet appareil menager _ usage commercial est instalte,

entretenu et utilise conformement aux instructions jointes ou fournies avec le produit, la marque Maytag de Whirlpool Corporation (ci-

apr_s designee "Maytag') paiera pour tes pi_ces specifiees par I'usine ou pour les pi_ces originales du fabricant de l'equipement

pour corriger tout vice de materiau ou de fabrication. Une preuve de la date d'achat d'origine est exigee pour obtenir un service dans

le cadre de la pr_sente garantie.

MAYTAG NE PRENDRA PAS EN CHARGE :

1. Tout autre coot y compris la main-d'oeuvre, le transport ou les droits de douane.

2. Les visites de service pour rectifier I'instaltation de I'appareil menager _ usage commercial, montrer _ I'utilisateur comment utiliser

I'appareil menager _ usage commercial, remplacer ou reparer des fusibtes ou rectifier le c_btage ou la plomberie du domicile.

3. Les r6parations Iorsque I'appareil menager _ usage commercial est utilise _ des fins autres qu'un usage commercial normal..

4. Les dommages imputabtes _ : mauvaise manipulation du produit lots de la livraison, vol, accident, modification, usage impropre

ou abusif, incendie, inondation, acres de Dieu, installation fautive ou installation non conforme aux codes Iocaux d'etectricite ou

de plomberie, ou l'utilisation de produits non approuves par Maytag.

5. Le ramassage et la livraison. Cet appareil menager _ usage commercial est congu pour _tre r_pare sur site.

6. Les r_parations aux pi_ces ou systemes resultant d'une modification non autorisee faite _ I'appareit menager _ usage commercial.

7. L'enl_vement et la reinstattation de I'appareil m_nager _ usage commercial si cetui-ci est instatte dans un endroit inaccessible ou

n'est pas instatte conformement aux instructions d'instattation foumies.

8. Aucun dommage dO _ des produits chimiques n'est couvert par la garantie.

9. Des modifications apportees _ I'immeubte, _ la piece ou aux lieux afin de permettre _ I'appareil menager _ usage commercial de

fonctionner correctement.

CLAUSE D'EXONERATION DE RESPONSABILIT¢ _AU TITRE DES GARANTIES IMPMClTES; LIMITATION DES RECOURS

LE SEUL ET EXCLUSIF RECOURS DU CLIENT DANS LE CADRE DE LA PRESENTE GARANTIE LIMITE_ECONSISTE EN LA

RFtPARATION PREVUE CI-DESSUS. LES GARANTIES IMPLICITES, Y COMPRIS LES GARANTIES APPLICABLES DE QUALIT¢:

MARCHANDE OU D'APTITUDE A UN USAGE PARTICULIER, SONT LIMITEES A UN AN OU _, LA PLUS COURTE PE_RIODE

AUTORISC:E PAR LA LOI. WHIRLPOOL N'ASSUME AUCUNE RESPONSABILIT¢: POUR LES DOMMAGES FORTUITS OU

INDIRECTS. CERTAINES JURIDICTIONS NE PERMETTENT PAS L'EXCLUSION OU LA LIMITATION DES DOMMAGES FORTUITS OU

INDIRECTS, OU LES LIMITATIONS DE LA DURE_EDES GARANTIES IMPLICITES DE QUALITE_ MARCHANDE OU D'APTITUDE A UN

USAGE PARTICULIER, DE SORTE QUE CES EXCLUSIONS OU LIMITATIONS PEUVENT NE PAS S'APPLIQUER DANS VOTRE CAS.

CETTE GARANTIE VOUS CONFERE DES DROITS JURIDIQUES SP¢:CIFIQUES ET VOUS POUVEZ E_GALEMENT JOUIR D'AUTRES

DROITS QUI PEUVENT VARIER D'UNE JURIDICTION A UNE AUTRE.

Si vous avez besoin de service, veuillez contacter votre distributeur autorise de buanderie & usage commercial Maytag. Pour Iocaliser

votre distributeur autorise de buanderie & usage commercial Maytag ou pour toute question via intemet, consulter :

www. MaytagCommerciatLaundry.com.

Pour toute correspondance ecrite :

Maytag Commercial Laundry Service Department

2000 M-63 North

Benton Harbor, Michigan 49022

9/07

Page is loading ...

Maytag MDE17CS Installation guide

Brand: Maytag

Model: MDE17CS

Category: Electric laundry dryers

Type: Installation guide

Download PDF

report

in other languages

italiano: Maytag MDE17CS Guida d'installazione
français: Maytag MDE17CS Guide d'installation
español: Maytag MDE17CS Guía de instalación

Maytag MDE17CS Installation guide

Maytag MDE17CS Installation guide

in other languages

Related papers

Other documents