ElectrIQ PD45E User manual

Brand: ElectrIQ

Model: PD45E

Category: Dehumidifiers

Type: User manual

ElectrIQ PD45E is a commercial large home office dehumidifier with a digital humidistat. It has a 40-liter per day water extraction capacity and is suitable for use in large living areas, offices, homes, and commercial applications. The device features an intelligent humidistat that allows you to set the desired relative humidity level, a laundry mode for drying clothes efficiently, a timer for delayed power-on or power-off, and a child lock for added safety. The dehumidifier also has a continuous drainage option and a washable filter.

USER MANUAL

COMMERCIAL LARGE HOME OFFICE

DEHUMIDIFIER WITH DIGITAL HUMIDISTAT

PD45E – 40 litres per day

Thank you for choosing electriQ.

Please read this user manual before using this innovative Dehumidifier and keep it safe for future reference

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

CONTENTS

SAFETY INSTRUCTIONS

INSTALLATION

PARTS

CONTROL PANEL

QUICK REFERENCE GUIDE

POSITIONING

WATER DRAINAGE

SETTING UP THE WIFI FUNCTION

CONTROLLING YOUR DEVICE FROM THE APP

CARE AND MAINTENANCE

TROUBLESHOOTING

TECHNICAL DATA

SAFETY INSTRUCTIONS

IMPORTANT

• Carefully read the instructions before operating the unit

• This appliance is for indoor use only and intended for use in a domestic environment

only. Any other use is not recommended by the manufacturer and may cause fire,

electrical shocks or other injury to user or property.

• Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.

• Installation must be in accordance with regulations of the country where the unit is

used.

• If you are in any doubt about the suitability of your electrical supply have it checked

and if necessary, modified by a qualified electrician.

• This dehumidifier has been tested and is safe to use. However, as with any electrical

appliance - use it with care.

• Disconnect the power before dismantling, assembling or cleaning.

• Avoid touching any moving parts of the appliance.

• Never insert fingers, pencils or any other objects though the guard

• This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities. It is also not intended for use by those with a

lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

• Do not leave children unsupervised with this appliance.

• Do not clean the unit by spraying it or immersing it in water.

• Never connect the unit to an electrical outlet using an extension cord. If a power outlet

is not available, one should be installed by a qualified electrician.

• Never operate this appliance if the cord, power adapter or plug is damaged. Ensure

the power cord is not stretched or exposed to sharp objects/edges.

• A damaged power supply cord should be replaced by the manufacturer or a qualified

electrician in order to avoid a hazard.

• Any service other than regular cleaning or filter replacement should be performed by

an authorized service representative. Failure to comply could result in a voided

warranty.

• Do not use the appliance for any purpose other than its intended use.

• Do not tilt the unit while in use. The unit is design to work only in vertical position.

• This dehumidifier must always be stored and transported upright, otherwise

irreparable damage may be caused to the compressor; if in doubt we suggest waiting

at least 24 hours before starting the unit.

• Avoid restarting the dehumidifier unless 5 minutes have passed since being turned

off. This prevents damage to the compressor.

• Never use the plug as a switch to start or turn off the dehumidifier. Use the provided

ON/OFF switch located on the control panel.

• Always place the unit on a dry and stable surface.

• The appliance should not be installed in laundry or wet rooms where the humidity is

higher than 85% RH

• Do not dry laundry above the unit to prevent water entering the dehumidifier. Place

the laundry at least 1 meter away from your dehumidifier.

• The appliance must be placed in a room without sources of ignition (for example: open

flames, an operating gas appliance or an operating electric heater).

• R290 refrigerant gas complies with European environmental directives.

• R290 has a low GWP (Global Warming Potential) of 3.

• The unit contains about 145g of R290 refrigerant gas.

• Do not use or store the dehumidifier in an unventilated space with an area smaller

than 7.0m

per unit.

• If the appliance is installed, used or stored in an unventilated room, the room must be

such as to prevent stagnation of possible leaks of refrigerant gas as there could be a

danger of fire or explosion should the refrigerant come into contact with electric

heaters, stoves or other sources of ignition.

• Refrigerant gas may be odourless.

• Do not use the product and contact the retailer for advice, if damage has occurred to

the unit which may have compromised the refrigerant system.

• Any repairs or maintenance must only be carried out on the unit by a suitably qualified

engineer. Before opening and servicing the unit the authorized engineer must be in

possession of a copy of the manufacturer’s service manual and must follow the safety

information contained within it to ensure all hazards are minimized.

• The refrigerant system should not be perforated or punctured.

• Do not place the unit next to heat sources (e.g. electrical fires, fireplaces, etc.)

• Avoid mishandling the dehumidifier. Dropping, throwing the unit can cause damage to

its internals and increases the risks of operating it.

• Do not store or use gasoline, petrol, paint, solvents or other flammable vapours or

liquids in the vicinity of this dehumidifier or any other appliance.

• This dehumidifier must not be used in spaces where there is a high concentration of

gases, solvent or other volatile organic compounds; in very dusty environments; in any

domestic, commercial or industrial environment where the air composition is

flammable.

ENERGY SAVING AND UNIT SAFETY PROTECTION TIPS

 Do not cover or restrict the airflow from the outlet or inlet grills. Do not operate and

follow troubleshoot procedure if the self-opening louvers do not open on power on.

 For maximum performance the minimum distance from a wall or objects should be 20

 Keep the filters or grills of the unit clean. Under normal conditions, filters or grills

should only need cleaning once every three weeks (approximately).

 Since the filters remove airborne particles, more frequent cleaning maybe necessary,

depending on the air quality. Vacuum both mesh and optional carbon filters and wash

the mesh filters with hot soapy water and dry them before placing them back in the

unit.

QUICK VISUAL SAFETY GUIDE ON WHERE OR WHEN NOT TO USE YOUR

DEHUMIDIFIER

INSTALLATION

Remove any water from within the water tank before starting the unit. In order to save energy do not open windows

or doors while the unit is running. Place the unit on a hard / flat surface. On first use run the unit continuously for

24 hrs.

TO REDUCE NOISE LEVELS:

Place a piece of carpet or a rubber mat under the unit to reduce any vibrations while the unit is running.

The PD45E dehumidifier uses compressor technology to extract water from the environment. Compressor

dehumidifiers are ideal for normal domestic or office environments which are heated during the winter

months and maintain a temperature above 12-15⁰C.

The dehumidifier is easy to move around on castors and are designed to extract unwanted humidity while

saving money due to its power saving logic. Its features an intelligent humidistat where the desired relative

humidity can be adjusted in increments of 5% between 30 and 90% ensuring your room is not dried too

much and power is not wasted.

FEATURES

Your electriQ dehumidifier belongs to the electriQ Pro range of domestic and commercial dehumidifiers.

They are designed to provide the best combination of:

1. Efficient, easy to use to use controls

2. Great for larger living areas such as spacious flats, offices and homes and for

commercial applications

3. Designed to complement any modern space

PARTS

Power cord

Water tank

Continuous drainage port

Filter

Rear casing

Air outlet

Top cover

Front casing

Water indicator

CONTROL PANEL

POWER

Turn the appliance on/off

MODE Button

Select the function of the unit between: DEHUMIDIFY, FAN and LAUNDRY

modes. The LED’s will illuminate to show which mode is selected.

DEHUMIDIFY: The unit will dehumidify and aim for the humidity set using the

up and down buttons.

FAN: Only the fan will run and water is not extracted.

LAUNDRY: The unit will dehumidify at the maximum level, ideal for drying

clothes.

HUMIDITY SETTING

Press the UP and DOWN buttons to select the desired relative humidity

level.DOWN can be repeatedly pressed unti CO is displayed, or UP can be

repeatedly pressed until AU is displayed

CO: Continuous mode, the unit will run continuously, and will only stop for

defrosting, or if the water tank is full.

AU: Automatic mode. The desired humidity is dependant on the room

temperature

≤ 20°C - Desired humidity is set to 60%

21 ≤ room temp ≤ 27°C - Desired humidity is set to 55%

˃ 27°C - Desired humidity is set to 50%

FAN SPEED

Use to select the fan speed. The LED’s above will illuminate to show the fan

speed selected.

Note: The fan speed cannot be changed in AU mode when the temperature is

above 27°C

TIMER

Press the TIMER button to program the timer. When the timer is activated the

"TIMER" light will be illuminated. Before programming the timer, ensure the

timer function has not been activated (the light must be off). The following timer

programs are available.

DELAYED POWER-ON FUNCTION: With the appliance in stand-by,

repeatedly press the TIMER button to select in how many hours time you

require the unit to start (0~24 hours).

DELAYED POWER-OFF FUNCTION: While the appliance is running with the

desired settings, repeatedly press the timer button to set in how many hours

time you require the unit to stop (0~24 hours).

CHILD LOCK

Hold the LOCK button for 5 seconds to activate the child lock. The LED

indicator will illuminate to show the child lock is activated. To turn it off hold the

LOCK button again for 5 seconds.

WIFI

Hold the WIFI button for 6 seconds to reset the WIFI module ready for

connection, or to change the connection method between AP (Access point)

and CF (Quick Connection) modes. This also resets the WIFI module.

OK INDICATOR

When lit, shows that the desired humidity set has been reached, and the

compressor is in standby mode

DEFROST INDICATOR

The appliance will defrost automatically when the coil sensor detects that the

internal temperature is too low. During defrosting the indicator will light up.

Once the defrost cycle has finished, the appliance will return to the mode that

was previously operating.

TANK FULL

When the water tank is full, the TANK FULL indicator light will flash, and the

unit will stop operating. Once emptied and replaced, the appliance will resume

operation.

DISPLAY

As default, the unit will display the current humidity of the room. The unit is

also able to display the current room temperature. Press the UP and DOWN

buttons at the same time to change between the units shown.

If the UP or DOWN button are pressed, the display will show the desired

humidity set on the dehumidifier.

While the timer is set, the unit will display the duration of the timer.

QUICK REFERENCE GUIDE

POWER Button: Press to turn the dehumidifier on and off.

MODE Button: Press to change the unit between dehumidify, fan and laundry mode.

TIMER: Repeatedly press the timer button to adjust the duration of the timer (1-24 hrs, start/ stop

timer).

If set while the unit is running: The number will represent the number of hours the unit will operate before

turning off. This will not be affected if the unit enters defrost mode or the tank is emptied and reinserted.

If set while the unit is in standby: The set number represents the period in hours after which the unit will

start. To cancel start / stop mode press the timer key again.

Up and Down Buttons: While the unit is in dehumidify mode these buttons can be used to

adjust the desired humidity level. The desired relative humidity can be set between 30 and

90% in 5% increments. Pressing DOWN below 30% will put the unit in continuous mode (CO).

Pressing UP above 90% will put the unit in auto mode. In auto mode the desired humidity

will be based on the room temperature.

AUTO MODE (AU)

ROOM TEMPERATURE

DESIRED HUMIDITY (%)

≤ 20°C

21 ≤ Room Temp ≤ 27°C

˃ 27°C

LAUNDRY MODE: When drying clothes it is advised for the dehumidifier to operate continuously with

maximum water extraction until the water tank is full. Set the unit to the laundry mode, and the unit will work

until the water tank is full. Do not place clothes directly over any of the vents on the dehumidifier. Make sure

that there is nothing blocking the hot air exhaust air flow and for best results place the laundry within 1.5

meters of the dehumidifier.

NOTES:

 If a permanent drainage pipe is fitted the unit will not stop operating. Setting the desired humidity to

around 35% is good for laundry mode, a quick drying boost, or in emergencies. It is not recommended

for long normal operation in a domestic or office environment.

 To allow more moisture in the air, press the up button and set to a higher desired humidity (e.g. 60-

70%).

 We recommend setting the humidity to 50-55%. This is great for domestic operation and dry

storage

 Setting the humidity to 60% is great for personal comfort and applications where 50% RH is

considered too dry

 Setting the humidity to 70% is ideal for unoccupied properties or where an economical run is needed

without the need to reduce the humidity further.

OTHER FEATURES AND INDICATORS

TANK FULL LIGHT

When the water tank is full, removed or incorrectly inserted the unit will stop dehumidifying, the tank full light will

illuminate. Empty the tank and reinsert it correctly to resume operation.

AUTO DEFROST

When frost builds up on the evaporator coils, the compressor will cycle off and the unit will go in to defrost mode.

Following completion of the defrost mode, the unit will return to the previously operating settings.

 When the unit is running in a room with a temperature between 5

C and 12

C, it will enter defrost mode

roughly every 30 minutes.

 When the unit is running in a room with a temperature between 12⁰C and 20⁰C, it will enter the defrost

mode roughly every 45 minutes.

HUMIDISTAT CONTROL AND FAN/COMPRESSOR OPERATION

 When the humidity of the room is 2% lower than the desired humidity the compressor will turn off

automatically but the fan will continue to operate to ensure that the air within the room is not stale. The

unit will use only a minimal amount of energy in fan mode.

 When the humidity of the room is equal to or higher than the desired humidity the compressor will restart

after a 3 minutes delay to protect the compressor.

AUTO-RESTART (on some models)

If the unit stops unexpectedly due to the power cut, it will restart with the previous function selected automatically

when the power resumes, and the 3 minute compressor protection has elapsed.

POWER

After the unit has stopped, to protect the compressor it is not recommended to resume operation for at least 10

minutes. Operation can resume after this period lapses. When the unit is restarted there is a 3 minutes delay

before compressor will start.

POSITIONING THE DEHUMIDIFIER

A badly positioned dehumidifier will have little effect. In positioning the dehumidifier please ensure circulation of

air in not restricted around the unit.

Allow at least 20 cm space around the unit. This

dehumidifier is designed only for indoor residential or office

applications and any industrial use will invalidate the

warranty.

Use in an enclosed area for maximum efficiency. Close all

doors, windows to create an effective operating

environment. Do not use outdoors.

Your electriQ dehumidifier will begin to protect your space from the harmful effects of excessive moisture as soon

as it is turned on. Excess moisture is dispersed throughout your home. For this reason, the dehumidifier should

be positioned in a central and clear location so that it can draw this moist air towards it from all over the home. A

warm hallway or landing is an excellent position for your dehumidifier. If possible, leave interior doors ajar to allow

air circulation.

Alternatively, if you have a serious problem in one area you can begin by positioning the dehumidifier there and

moving it to a more central location at a later date. For the most effective use, run your dehumidifier with external

doors and windows kept closed. Please note the unit should not be placed directly against a radiator or other

heat source.

When positioning your electriQ dehumidifier, ensure that it is placed clear of any obstacle that may limit the air

movement. Place the dehumidifier on a flat dry surface.

Note: Do not move the unit with water in the tank as it may tip over and spill water.

WATER DRAINAGE

When the water tank is full, the unit will stop automatically. When this happens the TANK FULL light will show

on the control panel.

NOTE: Only empty the water tank when it is full or before moving or storing the unit.

There are two ways to dispense collected water.

1. USE THE TANK

When the tank is full, the unit will automatically stop running, and the Tank Full

indicator will flash.

Slowly pull out the tank. Grip the tank by its handle securely, and carefully pull it

out. Empty the water tank and reinsert it into the dehumidifier. The tank must be

in place and securely seated for the dehumidifier to operate again. The

dehumidifier will re-start when the tank is restored in its correct position.

NOTES:

When you remove the water tank, do not touch sensors or any parts which are

situated behind tank. Doing so may damage the product. Be sure to push the tank gently all the way into the

unit. Banging the bucket against anything or failing to push it in securely into place may cause the unit not to

operate.

Do not remove any parts from the water tank or tank enclosure. The water full sensor will no longer be able to

detect the water level correctly and water may leak from the water tank.

2. CONTINUOUS DRAINAGE

Water can be automatically plumbed in or drained into a sink, a larger recipient or through the wall into an outside

drain by attaching a pipe to the unit (10 mm internal diameter) (not included). Remove the rubber bung and Insert

the pipe into the drain outlet on the back of the unit as shown here.

Make sure the connection between pipe and the drain outlet is tight and does not leak. Then direct the pipe

to a suitable drainage point. This unit uses gravity to dispose of water hence the drain should be lower than

the water outlet on the unit. Put the tank back into the unit. Be sure to run the water pipe downward and let

the water to flow out smoothly. Do not kink or bend the pipe.

The permanent drain can be used in conjunction with a water pump (e.g. when draining from a cellar) to lift

the water upwards.

SETTING UP THE WIFI FUNCTION

BEFORE YOU START

 Ensure your router provides a standard 2.4ghz connection.

 If your router is dual band ensure that both networks have different network names (SSID). The

provider of your router / Internet service provider will be able to provide advice specific to your router.

 Place the dehumidifier as close as possible to the router during setup.

 Once the app has been installed on your phone, turn off the data connection, and ensure your phone

is connected to your router via wifi.

DOWNLOAD THE APP TO YOUR PHONE

Download the ”TUYA SMART” app, from your chosen app store, using the QR codes below, or by

searching for the app in your chosen store.

Android IOS

CONNECTION METHODS AVAILABLE FOR SETUP

The smart device has two different setup modes, CF (Quick Connection) and AP (Access Point).

The quick connection is a quick and simple way to set the unit up. AP connection uses a direct

local wifi connection between your phone and the dehumidifier to upload the network details.

Before starting the setup, please ensure that your dehumidifier is in the correct standby mode for

the connection type you are attempting, the display your dehumidifier will indicate this.

CHANGING BETWEEN CONNECTION MODES / WIFI RESET

To change the unit between the two connection types, hold the WIFI button for 6 seconds. The

connection mode is signified by the frequency of the flashing wifi light. This will also remove any

previous WIFI configuration.

Connection Type

Frequency of Flashes

CF (Quick Connection)

Flashes twice per second

AP (Access Point)

Flashes once per second

1. Press on the register button

at the bottom of the screen.

2. Read the Privacy policy

and press the Agree

Button.

3. Enter your email address or

phone number and press

continue to register.

4. A verification code will be

sent by the method selected

in step 3. Enter the code into

the app.

2. The app is now registered.

It will automatically log you

in following reqistration.

5. Type in the password you

would like to create. This

needs to be 6-20 characters,

with letters and numbers.

SETTING UP YOUR HOME WITHIN THE APP

TUYA is designed so it can work with a large number of compatible smart devices within your

home. It can also be set up to work with multiple devices within different houses As such during

the setup process, the app requires that different areas are created and named to allow easy

management of all your devices. When devices are then added, they are assigned to one of the

rooms you have created.

CREATING ROOMS

1. Press on the ADD HOME

button.

3. Type in a name for your

home,

4. Press on the location button

to select the location of your

home. (See SETTING

YOUR LOCATION below)

5. New rooms can be added

by pressing the ADD

ANOTHER ROOM option at

the bottom. (See ADD

ANOTHER ROOM below)

6. Untick any rooms that are

not required on the app.

7. Press DONE in the top right

corner.

SETTING YOUR LOCATION

Use your finger to

move the orange

HOME symbol.

When the symbol

is in the

approximate

location of your

home, press the

confirm button in

the top right

corner.

ADD ANOTHER ROOM

Type in the

name of the

room, and

press Done in

the top right

corner

CONNECTING USING QUICK CONNECTION

Before initiating the connection, make sure the unit is in standby mode, with the WIFI light flashing

twice per second. If not follow the instructions for changing the connection mode. Also ensure

your phone is connected to the wifi network. (We advise turning mobile data off during setup)

2. Select the type of device

as “Dehumidifier”

3. Ensure the wifi light on the

dehumidifier is flashing

twice per second，then

press on the orange button

at the bottom of the screen

to confirm.

4. Enter your wifi password and

press confirm.

5. This will then transfer the

settings to the dehumidifier.

Wait for this to complete. If

this fails, retry. If still

unsuccessful please review

the troubleshooting section

for further help.

1. Open app and press “+” to

add device, or use the add

device button

CONNECTING USING AP MODE (ALTERNATIVE METHOD)

Before initiating the connection, make sure the unit is in standby mode, with the wifi light flashing

once per second. If not follow the instructions for changing the connection type. Also ensure your

phone is connected to the wifi network. (We advise turning mobile data off during setup)

1. Open app and press “+” to

add device, or use the add

device button

2. Select the type of device

as “Dehumidifier”

3. Press on the AP mode

button in the top right of the

screen.

4. Ensure the wifi light on the

dehumidifier is slowly

flashing (once per second),

then press on the orange

button at the bottom of the

screen to confirm

5. Enter your wifi password and

press confirm.

6. Go to network settings in your

phone and connect to the

“SmartLife xxx” connection.

There is no password to

enter. Then return back to the

app to complete setup.

This will then transfer the settings to the dehumidifier.

Once the connection process has completed, go back to the network settings on your phone to ensure

your phone has reconnected to your wifi router.

CONTROLLING YOUR DEVICE THROUGH THE APP

THE HOME SCREEN

Each device has its own entry on the home screen to allow the user to either quickly turn the unit on or off,

or to enter the device screen to make other changes.

DEVICE

SCREEN

Change Home: If you

have a number of units at

different houses, you can

change between them

Add Device: Add a device

to the app, and go through

the setup process.

Environmental

information: Provides

outdoor temperature and

humidity based on the

location details entered

Rooms: Use to view the

units set up within each

room

Smart Scene: Allows you

to program intelligent

behaviour based on the

internal and external

environment

Add Device: Add a device

to the app, and go through

the setup process.

Room Management:

Allows rooms to be added,

removed or renamed.

Profile: Provides the

option for changing

settings, and adding

devices using a QR code

provided by a friend.

ON / OFF Button: Use to

quickly turn the unit on or

off.

Name of dehumidifier:

Press to enter the Device

Screen

DEVICE SCREEN

The device screen is the main control screen for the dehumidifier, providing access to the controls to

amend the functions of the dehumidifier

ON / OFF Button: Use to

turn the unit on or off.

Edit Name: Use to

change the name of the

dehumidifier

Desired Humidity UP Button:

Use to increase the desired

humidity. Going above 90%

will put the unit into Auto Mode

(AU)

Current Room Temperature:

Displays the current room

temperature

Back: Returns to the

Home Screen

Desired Humidity Down

Button: Use to decrease

the desired humidity. Going

below 30% will put the unit

into Continuous Mode (CO)

Current Room Humidity:

Displays the current room

humidity

Function Tabs:

Change other settings for the

dehumidifier.

MODE:

Change the operating mode of

the dehumidifier between

Dehumidify, Laundry and Fan

SPEED:

Use to change the Fan speed

between Low and High

FUNCTION:

Use to activate child lock. The

other functions are not

supported on this model.

TIMER:

Use to add an off timer

while the unit is

running, or an on timer

while the unit is in

standby

SMART SCENES

Smart Scenes is a powerful tool providing the option to customise the operation of the dehumidifier based

both on conditions within the room and outside influences. This gives the user the option of specifying

much more intelligent actions. These are split into two catagories Scene and Automation.

SCENE

Scene allows for a one touch button to be added to the Home screen. The button can be used to change a

number of settings in one go, and can change all the settings within the unit. A number of scenes can

easily be setup, allowing the user to easily change between a number of preset configurations.

Below is an example of how to set up a scene:

1. Press on the Smart Scene

tab at the bottom of the

Home screen

3. Select Scene to create a

new Scene

2. Press on the Plus in the top

right corner to add a smart

scene.

4. Press the Pen next to

“Please Enter Scene Name” to

input the name for your Scene

Show on Dashboard: Leave

this on if you require the scene

to be displayed as a button on

the Home Screen

Press the Red Plus to add the

action required. Then select

the dehumidifier from the list of

devices.

5. Chose the function, set the

value for the function, and

then press the back button in

the top right corner, to return

to the previous screen.

6. Once all the functions required have been added, press the Save button in the top right corner to

finalise and save your new Scene

Page is loading ...

ElectrIQ PD45E User manual

Brand: ElectrIQ

Model: PD45E

Category: Dehumidifiers

Type: User manual

Download PDF

report

ElectrIQ PD45E User manual

ElectrIQ PD45E User manual

Related papers

Other documents