Pulsar PSBSEP04124 Operating instructions

Brand: Pulsar

Model: PSBSEP04124

Type: Operating instructions

This manual is also suitable for

PSBSEP04124 - v1.0

Pulsar PSBSEP04124 - v1.0 is a high-efficiency (70%) switched mode power supply for CCTV systems, designed for uninterrupted operation. It features four independent, adjustable DC voltage outputs (12-18V), each capable of delivering up to 1A of current, plus a separate 0.2A or 0.5A (jumper-selectable) charging current for two 7Ah/12V batteries.

The PSBSEP04124 includes several protection systems, including short-circuit (SCP), overload (OLP), and overheat (OHP) protection, as well as surge protection and protection against sabotage. It also has several technical outputs, including FAC (indicating AC power loss), FLB (indicating low battery voltage), and FPS (indicating PSU failure), which can be used to monitor the status of the device.

PSBSEP04124

v.1.0

PSBSEP 12-18V/4x1A/2x7Ah/SEP

Buffer, switched mode power supply for CCTV.

EN*

Edition: 2 from 16.09.2013

Supercedes the edition: 1 from 06.02.2012

PSBSEP04124 www.pulsar.pl

Features:

• 4 independent adjustable channels, delivering

uninterrupted voltage within the range of

12÷18VDC/4x1A

• fitting 2x7Ah/12V batteries

• 4 separate OVP protection systems, one per channel,

15V/18V/21V jumper selectable

• supply voltage: 230VAC

• high efficiency 70%

• separate circuit for battery charge, independent from

the preset output

• battery charge and maintenance control

• deep discharge battery protection (UVP)

• battery output protection against short circuit and

reverse polarity connection

• battery charging current: 0,2A/0,5A jumper selectable

• START for manual battery connection

• LED indication

• FAC technical output indicating AC power

loss

• FLB technical output indicating low battery

voltage

• FPS technical output indicating PSU failure

possible mounting of 4-channel MSEP412

module to YAP leads

• protections:

• SCP short-circuit protection

• OLP overload protection

• OHP overheat protection

• surge protection

• against sabotage

• warranty – 5 year from the production date

CONTENTS:

1. Technical description.

1.1 General description

1.2 Block diagram

1.3 Description of PSU components and connectors

1.4 Specifications

2. Installation.

2.1 Requirements

2.2 Installation procedure

3. Operating status indication.

3.1 LED indication

3.2 Technical outputs

4. Operation and use.

4.1. Procedure in case of a short circuit at the PSU output

4.2. Procedure in case of a short circuit at the BAT output or battery reverse polarity connection

4.3. Procedure in case of activating the PSU OVP system

4.4. Battery-assisted operation

4.5. Maintenance

Technical description.

1.1. General description.

A buffer PSU is intended for an uninterrupted supply to CCTV system devices requiring stabilized voltage

of 12V/DC (+/-15%). It features 4 channels, adjusted independently, delivering uninterrupted voltage which can

be set within the range of 12÷18VDC/4x1A. This enables compensation of voltage drops in complex CCTV

installations. The current capacity amounts to:

1. Output current 4 x 1A + 0,2A battery charge

2. Output current 4 x 1A + 0,5A battery charge

Total current of the receivers + battery: 4,5A max.

www.pulsar.pl PSBSEP04124

Chart 1.

Acceptable output current of the PSU is 4x1A with

the preset 12V voltage at the output. If this voltage

exceeds 12V, the receivers’ current consumption

shall be reduced, according to the chart 1.

In case of a power loss, a battery back-up is activated immediately. The PSU is mounted in a metal

enclosure (RAL 9003 colour) that accommodates 2x7Ah/12V batteries and a microswitch indicates door opening

(faceplate). The enclosure design enables mounting 4-channel video module featuring proper connection outlets

for the Yap leads (coax cable).

1.2 Block diagram

Fig.1. Block diagram of the PSU.

1.3 Description of PSU components and connectors

PSBSEP04124 www.pulsar.pl

Table 1. Elements of the PSU module.

Element no.

Fig. 2

Description

[1]

BAT

; pins – battery charging current adjustment

• I

BAT

= Ibat =0,2 A

• I

BAT

= Ibat =0,5 A

Caption: jumper on, jumper off

[2] START button (launching the PSU module from a battery)

[3] F

BAT

fuse in the battery circuit

[4] LB – LED indicating battery charge

[5]

LED indication:

AUX1 ÷ AUX4 – LEDs indicating the voltage presence at the particular outputs

FPS – LED indicating PSU failure

FLB – LED indicating low level of the battery

[6]

Connectors:

+BAT- DC supply output (+BAT= red, -BAT = black)

+AUX1- ÷ +AUX4- - DC power outputs (+AUX= +U, -AUX=GND)

FAC - AC absence technical output

- OC type (open collector)

hi-Z level = status: AC power failure

L level = status: AC supply

- R type - relay

FPS - technical output of the PSU operation status – OC type (open collector)

hi-Z level = status: AC power failure

L level = status: correct operation

FLB – technical output of the battery low level – OC type (open collector)

hi-Z level = status: failure

L level = status: correct operation

[7]

Jumper for fuse selection: fuse/PTC

[8] F1, F2, F3, F4 fuses in AUX (+) circuits

[9]

Selection jumper for over voltage protection:

- V

OVP

=18V

- V

OVP

=15V,

- V

OVP

=21V

The level of protection is to be set min. 1,5V higher than the output voltage.

[10] V5

ADJ

potentiometer, voltage adjustment at the BAT output

[11]

Connector of extra, external LED indication

[12] V1

ADJ

÷ V4

ADJ

potentiometer, voltage adjustment at the AUX1 ÷ AUX4 outputs

[13] AC connector – module’s supply

[14] red LED– indicating presence of power at the AC output

[15]

Adjustment jumpers:

BAT

; pin - configuration of UVP battery protection function

• P

BAT

= battery protection (disconnection) off

• P

BAT

= battery protection (disconnection) on

, J1, J2; pins – configuration of time lag indication for FAC network absence:

• J1= , J2= time lag T= 5s

• J1= , J2= time lag T= 140s

• J1= , J2= time lag T= 17m

• J1= , J2= time lag T= 2h 20m

Caption:

jumper on, jumper off

www.pulsar.pl PSBSEP04124

Fig.2. View of the PSU’s pcb.

Fig.3. The view of the PSU.

Table 2. Elements of the PSU (see fig. 3).

Element no.

[fig. 3]

Description

[1]

Isolation transformer

[2] F

MAIN

fuse in the power supply circuit (230V/AC)

[3]

L-N connector 230V/AC,

PE protection connector

[4]

Battery connectors +BAT = red, - BAT = black

[5]

Pcb bard of the PSU (tab. 1, fig. 2)

[6] TAMPER; micro switch (contacts) for sabotage protection (NC)

PSBSEP04124 www.pulsar.pl

1.4 Specifications:

- electrical specifications (tab.2)

- mechanical specifications (tab.3)

- operation safety (tab.4)

- operating specifications (tab.5)

Electrical specifications (tab. 3).

Mains supply 230 VAC (-15%/+10%)

Current consumption 0,5A@230V AC max.

Power frequency 50Hz

PSU power 60W max.

Efficiency 70%

Output voltage 4 x 12V

Output voltage adjustment range 12÷18V DC each output adjusted separately

Output current

4x 1A + 0,2A battery charge or

4x 1A + 0,5A battery charge

Output voltage escalation, decrease, and

keeping time

2ms / 20ms / 60ms

Ripple voltage 50 mV p-p max.

Current drawn by the PSU systems 85 mA – battery-assisted operation

Battery charging current 0,2A/0,5A I

BAT

jumper selectable

Short-circuit protection SCP

200% ÷ 250% of PSU module power - current limitation by a

fuse (fuse-element replacement required)

Overload protection OLP

110% ÷ 150% (@25ºC) of PSU module power - current limitation

with the fuse/PTC, manual restart (failure requires disconnection

of the DC output circuit)

Ripple voltage 15V/18V/21V –selected by the ”OVP” jumper, independently for

each channel

Battery circuit protection SCP and

reverse polarity connection

4A - current limitation, F

BAT

fuse (failure requires fuse-element

replacement)

Deep discharge protection UVP <20,0 V (± 5%) – disconnection of the battery terminal

Surge protection 4 x varistors

Sabotage protection:

- TAMPER output indicating enclosure

opening

- microswitch, NC contacts (enclosure closed),

0,5A@50V DC (max.)

LED indication YES – LEDs

Technical outputs:

- FAC; output indicating AC power

failure

- FLB; output indicating low battery

voltage

- FPS;

technical output of the PSU

operation status

- OC type, 50mA max. normal status: L (0V) level, failure: hi-Z

level (automatic return after restoration of correct operation)

- R – relay type, 1A@ 30Vdc/50Vac max.

time lag, approx. 5s/140s/17min/2h20m (+/-5%)

- OC type, 50mA max. normal status: L (0V) level, failure: hi-Z

level V

BAT

< 23V

- OC type, 50mA max. normal status: L (0V) level, failure: hi-Z

level (automatic return after restoration of correct operation)

F1 ÷ F4 fuse

BAT

fuse

MAIN

fuse

F 1A /250V or PTC 1,1A

F4A / 250V

T 1A / 250V

Mechanical specifications (tab. 4).

Enclosure dimensions 350 x 275 x 100+8 (355 x 280 x 108) (WxHxD)

Fixing see fig. 3

Fitting battery 2 x 7Ah/12V (SLA) max.

Net weight 3,70/4,0kg

Enclosure Steel plate, DC0, 0,8mm thick, RAL9003

Closing Cheese head screw x2 (at the front)

Connectors Outputs: Ф0,41÷1,63 (AWG 26-14)

Notes

The enclosure does not adjoin the assembly surface so that cables can be led.

www.pulsar.pl PSBSEP04124

Operation safety (tab.5).

Protection class PN-EN 60950-1:2004 I (first)

Protection grade PN-EN 60529: 2002 (U) IP20

Electrical strength of insulation:

- between input (network) circuit and output circuits of the PSU (I/P-O/P)

- between input circuit and PE protection circuit (I/P-FG)

- between output circuit and PE protection circuit (O/P-FG)

3000 V/AC min.

1500 V/AC min.

500 V/AC min.

Insulation resistance:

- between input circuit and output or protection circuit

100 MΩ, 500V/DC

Operating specifications (tab.6).

Operating temperature -10ºC...+40ºC (see: chart 1)

Storage temperature -20ºC...+60ºC

Relative humidity 20%...90%, without condensation

Vibrations during operation unacceptable

Impulse waves during operation unacceptable

Direct insolation unacceptable

Vibrations and impulse waves during transport PN-83/T-42106

2. Installation.

2.1 Requirements

The buffer PSU is to be mounted by a qualified installer, holding relevant permits and licenses (applicable

and required for a given country) for 230V/AC interference and low-voltage installations. The unit should be

mounted in confined spaces, in accordance with the 2nd environmental class, with normal relative humidity

(RH=90% maximum, without condensation) and temperature from -10°C to +40°C. The PSU shall work in a vertical

position that guarantees sufficient convectional air-flow through ventilating holes of the enclosure.

1. Output current 4 x 1A + 0,2A battery charge

2. Output current 4 x 1A + 0,5A battery charge

Total current of the receivers + battery: 4,5A max.

Acceptable output voltage of the PSU amounts to 4x1A with the 12V voltage set at the output. If the voltage value

AT the output is higher than 12V, limit the receivers’ current consumption according to chart1.

As the PSU module is designed for a continuous operation and is not equipped with a power-switch,

therefore an appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user

shall be informed about the method of unplugging (most frequently through separating and assigning an

appropriate fuse in the fuse-box). The electrical system shall follow valid standards and regulations.

2.2 Installation procedure.

1. Before installation, cut off the voltage in the 230V power-supply circuit.

2. Mount the PSU in a selected location and connect the wires.

3. Connect the power cables (~230Vac) to L-N clips of the PSU. Connect the ground wire to the terminal marked by

the earth symbol – “ ” on the plate. Use a three-core cable (with a yellow and green PE protection wire) to make

the connection. Lead the cables to the appropriate terminals of the connection board through the bushing.

The shock protection circuit shall be performed with a particular care, i.e. the yellow and

green wire coat of the power cable shall stick to one side of the terminal marked with the ‘ ’

earth symbol in the PSU enclosure. Operation of the power supply without a properly made

and fully operational shock protection circuit is UNACCEPTABLE! It can result in device

damage or an electric shock.

4. Connect the receivers’ cables to the +AUX, -AUX connectors of the terminal block on the PSU board.

5. If necessary, connect the devices’ wires to the technical outputs:

- FAC; AC status indication (alarm panel, controller, indicator, LED, etc.)

- FPS; technical output of the PSU operating status.

- FBL; technical output of the battery operating status.

6. Allowing of the battery parameters, determine the maximum charging current using the I

BAT

jumper.

PSBSEP04124 www.pulsar.pl

7. With the OVP1 ÷ OVP4 jumpers, choose the over voltage protection, separately for each channel. The protection

level must be set min. 1,5V higher than the output voltage.

8. Supply the ~230V/AC to the transformer (the AC red diode and AUX diode should be permanently illuminated).

9. With the V

ADJ

potentiometer, set the required output voltage value, separately for each channel, monitoring the

voltage at the AUX output of the power supply.

10. Connect the batteries in series, in accordance with the markings: +BAT red to 'plus', -BAT black to 'minus’.

11. Check the PS operating status indication: green LEDs at the AUX1 ÷ AUX4 outputs.

12. Once the tests and operation control have been completed, the enclosure can be locked.

3. Operating status indication.

3.1 LED indication

The PSU is equipped with 8 LEDs in the front panel:

RED LED:

• on – the PSU is supplied with 230V AC voltage

• off – no 230V AC power

RED LED:

• on – low battery voltage V

BAT

<23V

• off – correct battery voltage

RED LED:

• on – PSU failure

• off – no failure

YELLOW LED:

• on – battery charging process

• off – no battery charge

GREEN LED:

• on – DC voltage at the AUX1… AUX4 output

• off – no DC power at the AUX1… AUX4 output

Additionally, the PSU is equipped with LEDs inside the enclosure – Fig. 2 and 3.

3.2 Technical outputs.

The PSU has some indication outputs:

• FAC – technical output indicating absence of AC power:

- OC type output that indicates loss of the AC supply. Under normal status - with the 230V supply, the AC

output is fault to ground (status L – 0V). In case of power loss, the PSU output is switched into high

impedance state –hi-Z after a time period set by the J1 and J2 jumpers: 5s/140s/17m/2h20m.

- R – relay type output that indicates loss of the AC supply. In case of the power loss, the power supply unit

will switch the relay’s contacts after a time period set by the J1 and J2 jumpers: 5s/140s/17m/2h20m.

CAUTION! In Fig. 2 the contact set show a potential-free status of the relay. That corresponds to a

state with no AC power (AC power loss).

• FPS – technical output of the PSU operation status: - OC type output indicating the PSU failure (a short

circuit, an overload). Under normal status (during correct operation) the output is connected to ground (L

level – 0V). In case of a failure, the output is switched into high impedance state – hi-Z.

• FLB – technical output of the battery low level: - OC type output indicating low level of the battery

during battery-assisted operation. For battery voltage of V

BAT

>23V the output is connected to ground (L – 0V

level). If the battery voltage drops below V

BAT

<23V, the output will be switched into high impedance state - hi-

The technical outputs are implemented in an OC - open collector system shown in the following diagram:

www.pulsar.pl PSBSEP04124

Fig. 5. Electrical diagram of the OC technical outputs.

• TAMPER - output that indicates unwanted opening of the PSU: contains volt-free (potential-free)

contacts indicating the door status - unit closed: contacts normally closed (NC), unit opened: contacts

normally open (NO)

4. Operation and use.

4.1 Procedure in case of a short circuit at the PSU output

The AUX1 ÷ AUX4 PSU output is protected against a short circuit by fuses or polyswitches (the selection is

made by the FS-x jumper). If the fuse-assisted protection has been chosen, replace the fuse (of the same

parameters) after a failure. If the polyswitch-assisted protection has been chosen, there will be an automatic

disconnection of the output voltage indicated by the green diode going out. Then, cut off the load from the PSU

output for approx. 1 minute.

4.2. Procedure in case of a short circuit at the BAT output or battery reverse polarity connection

In case of a short circuit at the BAT output or a battery reverse polarity connection, the F

BAT

fuse in the battery

circuit becomes permanently damaged. To restore the voltage at the BAT output, replace the fuse.

4.3 Procedure in case of activating the PSU OVP system

The PSU is protected against over voltage at the AUX1 ÷ AUX4 outputs. The over voltage protection threshold

is selected by the OVP-x jumpers. When the OVP system is activated, the output voltage is automatically cut off.

This is indicated by the AUX green diode going out and illumination of the appropriate OVPx diode. Restoring the

correct operation is possible after lowering the output voltage with a potentiometer or by increasing the protection

threshold.

The level of protection is to be set min. 1,5V higher than the output voltage.

4.4. Battery-assisted operation

In case of the main power outage, the device is immediately switched into a battery-assisted operation.

In order to run the PSU from the battery only, connect the BAT connectors in accordance with the signs: + BAT red

to ‘plus’ and, - BAT black to 'minus’ then press the START button on the main board and hold it for 5 seconds.

The PSU module is equipped with the discharged battery disconnection system (UVP),

configured by the P

BAT

jumper. The protection mode is off when the P

BAT

jumper is removed.

4.5. Maintenance

Any and all maintenance operations may be performed following the disconnection of the PSU from the

power supply network. The PSU does not require performing any specific maintenance measures. However, in

case of dust, clean the interior with compressed air. Periodically, the condition of the batteries should be checked.

In case of faults (e.g. capacity loss, too high internal resistance), the batteries should be exchanged to new ones.

In case of fuse replacement, use a replacement of the same parameters.

PSBSEP04124 www.pulsar.pl

WEEE MARK

According to the EU WEE Directive – It is required not to dispose of electric or electronic

waste as unsorted municipal waste and to collect such WEEE separately.

CAUTION! The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed of but

recycled according to the applicable law.

Pulsar K.Bogusz Sp.j.

Siedlec 150, 32-744 Łapczyca, Polska

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

e-mail: biuro@pulsar.pl, sales@pulsar.pl

http:// www.pulsar.pl, www.zasilacze.pl

GENERAL WARRANTY CONDITIONS

1. Pulsar K. Bogusz Sp.j. (the manufacturer) grants a five-years warranty for the equipment, counted from the device’s

production date.

2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the

manufacturer’s discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects,

unless such defects have been reported within the warranty period (item 1).

3. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office

of the manufacturer.

4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the

defect.

5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenienve,

however not later that within 14 days from the delivery to the service centre of the manufacturer.

6. The repair period mentioned in item 5 may be prolonged, if there are no technical possibilities to carry out the repairs,

or if the equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.

7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively.

8. The warranty does not cover the defects of the equipment, resulting from:

- reasons beyond the manufacturer's control,

- mechanical damage,

- improper storage and transport,

- use that violates the operation manual or equipment’s intended use

- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,

- improper installation and configuration (in defiance with the manual),

9. The warranty is void in any of the following circumstances:

- construction changes

- repairs carried out by any unauthorized service center

- damage or removal of warranty labels

- modifications of the serial number

10. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to

the wholesale prices suggested by the manufacturer on the day of purchase.

11. The manufacturer takes no reponsibility for the defects that result from:

- the damaging, malfunctioning or inability to operate the equipment

- defects that result from using the equipment outside its stated specifications and operating parameters failing to abide

by the recommendations and requirements contained in the manual, or the use of the equipment.

Pulsar PSBSEP04124 Operating instructions

Brand: Pulsar

Model: PSBSEP04124

Type: Operating instructions

This manual is also suitable for

PSBSEP04124 - v1.0

Download PDF

report

Pulsar PSBSEP04124 Operating instructions

This manual is also suitable for

Pulsar PSBSEP04124 Operating instructions

Related papers

Other documents