Futrex 5000A/ZL User manual

Brand: Futrex

Model: 5000A/ZL

Category: Networking

Type: User manual

This manual is also suitable for

USER'S MANUAL

FUTREX

-5000A/WL

BODY FAT AND FITNESS COMPUTER

FUTREX INC.

6 Montgomery Village Avenue

Suite 620

Gaithersburg, MD 20879

Version 8.5

FUTREX-5000A/WL USER'S MANUAL

This manual provides you with all the information needed to operate the FUTREX-5000A/WL.

Table of Contents

Appearance and Part Names ................................................................................... 1

Preparation ................................................................................................. 3

Printer Paper Installation ...................................................................................... 4

Models of the Futrex Body Fat & Fitness Computer .................................................................. 5

Percent Body Fat Estimation ................................................................................... 6

Selecting the Biceps Measurement Site .......................................................................... 14

Selecting the Triceps Measurement Site ......................................................................... 15

Selecting the Thigh Measurement Site .......................................................................... 16

Adjusting the Body Fat Percentage Readout ...................................................................... 17

Estimating Relative Fat Distribution ............................................................................. 18

Self Measurement of Percent Body Fat .......................................................................... 20

Date ..................................................................................................... 22

Printout Programs .......................................................................................... 23

Fitness Analysis ................................................................................... 23

Update Analysis ................................................................................... 25

Color Printer Physical Rating .................................................................................. 27

Function Mode ............................................................................................. 28

Trouble Shooting ........................................................................................... 31

General Specifications ....................................................................................... 34

Keypad Description ......................................................................................... 35

Note: FUTREX CAUTIONS THE USER AND/OR INDIVIDUAL TESTED TO SEEK THE ADVICE OF A HEALTH CARE

PROFESSIONAL PRIOR TO UNDERTAKING ANY NUTRITION AND/OR EXERCISE PROGRAM.

APPEARANCE AND PART NAMES

1. Main Body

2. Optical Standard

3. Light Wand

PREPARATION

PRINTER PAPER INSTALLATION

1. Battery Installation

Insert 6 1.5V "AA" size alkaline batteries into the battery

compartment located on the rear of the Main Body. Be sure the

batteries are oriented as indicated in the battery compartment.

NOTE: Batteries must be alkaline type. Other types will not work.

2. Light Wand

Connect the Light Wand Cable to the connector jack located on

the right hand side of the Main Body.

It is recommended that the Connector always remain attached to

the Main Body. This will avoid possible damage to the connector.

3. A/C Adapter

Connect the A/C Adapter cable to the connector jack located on

the right hand side of the Main Body (the jack closest to the top of

the unit).

Remove the clear plastic cover from the printer.

Start feeding the paper into the slit inside the Paper Roll

Compartment by pressing the PAPER FEED key.

NOTE: The paper must be thermal paper and cut square prior

to inserting.

MODELS OF THE FUTREX BODY FAT AND FITNESS COMPUTER

CAUTION: This Manual is only for use with the FUTREX-5000A/WL

There are three models available for estimating percent body fat in humans:

! FUTREX-5000/XL

Estimates the percent body fat of Adults only (ages 18-80)

! FUTREX-5000A/ZL

Estimates the percent body fat of:

1) Adults

2) Adolescent Children (13-17)

3) Pre-Adolescent Children (5-12)

When age is entered, the FUTREX-5000A/ZL automatically sets the unit to the proper calibration (e.g. if you entered the

subject's age as 14 during the Body Fat Measurement Sequence (page 6), the FUTREX-5000A/ZL will use its Adolescent

calibration to determine percent body fat).

! FUTREX-5000A/WL

Includes special high school wrestling calibrations as well as all features of the FUTREX-5000A/ZL.

PERCENT BODY FAT MEASUREMENT

NOTE: If "2" (i.e. "NO") is pressed, skip the following and go to Step 5.

TO ESTIMATE PERCENT BODY FAT:

1) Turn Power Switch ON.

The display will show a software version number (e.g. AO.51) and will then start a 15 second countdown. The

display will show Sd.

2) Insert Light Wand into Optical Standard. Be sure the white stripe from the Light Wand is aligned with the white

stripe from the Optical Standard.

3) Press the ZERO ADJUST Key.

The display will now show 0.0. The zero adjustment has been made.

Remove Light Wand from the Optical Standard.

Install the Light Shield on the Wand as shown in the sketch (allow the Wand to protrude from the edge of the

shield by about 1/4 of an inch). The Light Shield was provided to ensure that no external light interferes with the

estimation of percent body fat. Therefore, this shield should always be used when estimating percent body fat.

The FUTREX-5000A/WL is ready to start the body fat estimation sequence.

4) The printer will ask "Wrestler Cal: 1 = YES, 2 = NO". If the desire is to measure a wrestler press the "1" key,

otherwise press "2".

NOTE: If "1" is pressed, skip the following and go to Step 5.

4A) The printer will ask "ENTER # SITES: 1 or 3".

There are two alternative measurement methods.

! One Site Measurement - The measurement is on the midpoint biceps of the dominant arm (the arm

used for writing).

! Three Site Measurement - The measurement is made combining data from three body sites:

! Biceps - The first measurements are at the midpoint of the biceps of the dominant arm; i.e.,

the arm used for writing. Measurement point on the front of the arm midway between the

armpit and the inside of the elbow.

! Triceps - The second measurements are at the midpoint of the triceps of the dominant arm.

Measurement point on the back of the upper arm midway between the shoulder and elbow.

! Thigh - The third measurements are at the thigh. Measurement point on the front of the thigh

midway between groin line and the top of the patella (knee).

4b) Press ENTER to start the body fat estimation sequence.

4c) Enter Weight in lbs. or kg. (refer to page 28 to switch between English and Metric Units). Press ENTER.

4d) Enter Height in inches or cm.

4e) Printer will show MEASURE BICEPS.

Place Light Wand firmly on biceps of the dominant arm (see page 14 for locating exact measurement point).

NOTE:

IT IS IMPORTANT TO: Aim the silver stripe of the Light Wand directly toward the shoulder. Keep the

arm relaxed (do not permit the subject to flex his/her muscles). A relaxed

biceps can be achieved by having the subject seated while resting his arm

(elbow bent) on a table.

Use the Light Shield to block the external light. Always avoid measurements

under strong lights (e.g. direct sunlight) because errors may occur.

CAUTION: Do not move the Light Wand while the decimal point is illuminated. The actual

measurement is being made at that time.

NOTE: Aim silver stripe directly toward the shoulder. Keep arm relaxed.

4f)

Press ENTER.

The display will flash a decimal point following the number "1a".

Then

the number "2a" will be displayed.

4g) Remove the Light Wand and replace it on the same point on the biceps. Press ENTER. The display will flash a

decimal point, then the number "1b".

4h) Place Light Wand firmly on Triceps of same arm (see page 15 for exact measurement point).

Press ENTER. The display will flash a decimal point. Don't move Light Wand until "2b" is displayed.

4i) Remove Light Wand and replace it on the same point on the triceps. Press ENTER. The display will flash a

decimal point. Don't move Light Wand until "1c" is displayed.

NOTE: Aim silver stripe directly up the leg. Press ENTER. The display will flash a decimal point. Don't

move Light Wand until "2c" is displayed.

NOTE: Steps 5 through 16 are not applicable. Those steps are for measurements using only the biceps.

NOTE: The age entered in Step 6 automatically places the instrument into the proper calibration for

estimation (i.e. adults 18 - 80, adolescents 13 - 17, pre-adolescents 5 - 12).

4j) Place Light Wand firmly on thigh at same side of body that the arm was measured; e.g. if right arm, then

measure right thigh. (See page 16 for exact measurement point.)

4k) Remove Light Wand and replace it on the same point on the thigh. Press ENTER. Display will again flash a

decimal point. Don't move the Light Wand until percent fat is displayed and printing starts.

Press ENTER to start the body fat estimation sequence.

6) Enter Age in years.

7) Enter Sex by pressing the MALE or FEMALE Key.

8) Enter Weight in lb or kg. (Refer to page 28 to switch between English and Metric Units). Press ENTER.

9) Enter Body Frame by pressing the SMALL, MEDIUM or LARGE Key.

There are many methods for estimating Frame Size. Futrex does not recommend any specific method but does

offer two techniques often used for determining frame size:

a) Ankle Girth

! Measure the ankle girth at the smallest point above the ankle with the tape as tight as

possible.

NOTE: If you have long fingers, this method may underestimate your frame size.

! Standards

Small Frame Medium Frame Large Frame

Men Less than 8 in. 8 to 9.25 in. Greater than 9.25 in.

Women Less than 7.5 in. 7.5 to 8.75 in. Greater than 8.75 in.

b) Wrist Girth

! Place your left thumb and middle finger around your right wrist and gently squeeze your

fingers together.

! Small Frame - Fingers overlap

! Medium Frame - Fingers touch

! Large Frame - Fingers do not touch

10) Enter Height in inches or cm (whole numbers only: e.g. 68 in. is acceptable). Refer to page 28 to switch between

English and Metric units. Press ENTER.

11) Enter F.I.T. Value

The following procedure provides a quantitative method to determine a subject's Physical Activity Rating.

A person's F.I.T. value is a function of 3 parameters:

! Exercise Frequency - How often the exercise is performed.

! Exercise Intensity - How much energy is expanded during exercise.

! Exercise Time - How many minutes the exercise is performed during each session.

The F.I.T. value is calculated by multiplying all three parameters:

F.I.T. = Frequency x Intensity x Time

11A) Enter Frequency Value. Press ENTER.

FREQUENCY 5 Daily or almost daily (6 or 7 times per week)

4 3 to 5 times per week

3 1 or 2 times per week

2 A few times per month

1 Less than once per month

11B) Enter Intensity Value. Press ENTER.

INTENSITY 5 Over 90 PERCENT OF YOUR MAXIMUM HEART RATE.

Competitive athlete (sprinting, speed swimming, distance cycling,

seasoned wrestler, racquetball, body builder, high impact

aerobics)

4 80-90 PERCENT OF YOUR MAXIMUM HEART RATE.

Intermittent aerobic activities (football, soccer, lacrosse, hockey,

moderate to heavy weight training, basketball, jogging, mountain

biking)

3 60-80 PERCENT OF YOUR MAXIMUM HEART RATE.

Moderate aerobic activity (speed walking, singles tennis,

gymnastics, light weight training, in-line skating, softball, casual

biking)

2 35-60 PERCENT OF YOUR MAXIMUM HEART RATE. Light

aerobic activity (brisk walking, doubles tennis, golfing, hiking)

1 LESS THAN 35 PERCENT OF YOUR MAXIMUM HEART RATE.

Activities of daily living (gardening, child care and normal walking)

NOTE:

IT IS IMPORTANT TO: Aim the silver stripe of the Light Wand directly toward the shoulder.

Keep the arm relaxed (do not permit the subject to flex his/her

muscles). A relaxed biceps can be achieved by having the subject

seated while resting his arm (elbow bent) on a table.

Use the Light Shield to block the external light. Always avoid

measurements under strong lights (e.g. direct sunlight) because

errors may occur.

CAUTION: Do not move the Light Wand while the decimal point is illuminated. The

actual measurement is being made at that time.

11C) Enter Time Value. Press ENTER.

TIME 4 Over 30 minutes

3 20 - 30 minutes

2 10 - 20 minutes

1 Under 10 minutes

12) Place Light Wand firmly on biceps of the dominant arm (see page 14 for locating exact measurement point).

13) Press ENTER.

The display will flash a decimal point following the number "1". Then the number "2" will be displayed.

14) Remove the Light Wand and replace it on the same point on the biceps.

15) Press ENTER.

The display will flash a decimal point following the number "2".

16) Percent Body Fat is displayed and printed.

The FUTREX-5000A/WL will also print the following information:

! Fat Weight (lbs of body weight that is fat).

! Lean (fat-free) body weight.

! Total Body Water (FUTREX-5000A/WL Adult Users only). This is the calculation of the subject's

normal hydration state. The percent body water is based on research that has shown lean tissue to be

composed of approximately 73% water, whereas fat contains 4 to 8% water. For example:

Men between 6 - 24% Fat = 69 - 57% Water

Women between 9 - 35% Fat = 67 - 50% Water

To Repeat A Measurement

Press ENTER and follow the steps outlined under 5-16.

Off Message

An Off Message will appear and the FUTREX-5000A/WL Automatic Power Down feature will turn the unit off if the user

has not pressed any key for 6 minutes. To use the unit again, turn the Power Switch OFF and ON again.

SELECTING THE BICEPS MEASURING SITE

NOTE: It is suggested that the person being measured press the ENTER key with the hand not being

measured.

1) Using a Biceps Locator or the scale provided on the Arm Band, measure the length between the armpit and the

inside of the elbow.

2) To mark the Measurement Point, measure halfway between the armpit and the elbow at the "belly" of the biceps

muscle. (More technically stated: measure along the exterior line of the biceps halfway between the antecubital

fossa and the acromion).

To mark this measurement site, place a small line on the medial side of the spot with a yellow highlighter or pen.

3) Place the Light Wand on the Measurement Site with one hand. Place your other hand behind the triceps, using

your thumb and middle finger to hold the black foam disk around the arm to block out external light.

4) Body Fat Measurement is described on pages 6 - 10.

SELECTING THE TRICEPS MEASURING SITE

NOTE: It is suggested that the person being measured press the ENTER key with the hand not being

measured.

1) Using a Biceps Locator measure the length between the top of the shoulder to the elbow to find the midpoint.

2) To mark the Measurement Point, place a small line on the medial side of the spot with a yellow highlighter or

pen.

3) Place the Light Wand on the Measurement Site with one hand.

4) Body Fat Measurement is described on pages 6 - 10.

SELECTING THE THIGH MEASUREMENT SITE

NOTE: It is suggested that the person being measured press the ENTER key with the hand not being

measured.

1) Using a Biceps Locator measure the length between the groin line and the top of the patella (knee) to find the

midpoint.

2) To mark this measurement site, place a small line on the medial side of the spot with a yellow highlighter or pen.

3) Place the Light Wand on the Measurement Site with one hand.

4) Body Fat Measurement is described on pages 6 - 10.

ADJUSTING THE PERCENT BODY FAT READING

The FUTREX-5000A/WL has been carefully calibrated to provide body fat estimates. The calibration is traceable to the

generally accepted hydrostatic procedure.

However, some users may desire to have the FUTREX-5000A/WL reading traceable to their own laboratory. For those

users the following adjustment procedures are provided for each calibration set (i.e. adult, adult without exercise level term,

adolescent, preadolescent):

1 Turn unit on.

1) During countdown press CLEAR, SELECT PROGRAM, RISKS.

2) The digital display will read "A1". To change to a specific calibration set:

Adult Calibration (older than 17 years) -- press ENTER.

Adolescent Calibration (13 - 17 years) -- press 3, then ENTER.

Preadolescent (5 - 12 years) -- press 4, then ENTER.

3) The digital display will show the value of the optical standard.

4) If no change to the calibration is desired - press CLEAR.

5) If you wish to change the calibration:

Press SELECT PROGRAM, then press RISKS. The display will show "0.0" (if no calibration adjustment has been

made) or the previously entered adjustment value.

6) To adjust the calibration:

Press the numbered key to enter the amount of adjustment. For example, if you want to decrease the

instrument's readings by 1.0% - press 1, press 0, then the minus sign, and then ENTER. All future body fat

readings will now read 1.0% lower.

8) Once the correct offset has been entered into the unit, press ENTER. The adjusted optical standard value will be

ESTIMATING RELATIVE FAT DISTRIBUTION

displayed.

9) To exit this mode: Press CLEAR.

In addition to estimating percent body fat, a relative body fat estimation on other sites of the body (e.g. quadriceps,

abdominal region) can be obtained using the FUTREX-5000A/WL.

1 Turn Power Switch ON.

The display will show a software version number (e.g. AO.51) and will then start a 15 second countdown. The

display will show "Sd".

1) Insert Light Wand into Optical Standard.

The silver stripe on the Light Wand should be lined up with the silver stripe on the Optical Standard.

2) Press the ZERO ADJUST Key.

The display will now show "0.0". The zero adjustment has been made.

3) Press the Number "2" Key.

This will shut off the printer function.

4) Remove Light Wand from the Optical Standard.

The FUTREX-5000A/WL is ready to estimate relative body fat. The display will show "1".

5) Place the Light Wand in the Light Shield and place firmly on the body part where you want to measure the

"Relative Fat".

Page is loading ...

Futrex 5000A/ZL User manual

Brand: Futrex

Model: 5000A/ZL

Category: Networking

Type: User manual

This manual is also suitable for

Download PDF

report

Futrex 5000A/ZL User manual

This manual is also suitable for

Futrex 5000A/ZL User manual

Related papers

Other documents