ViewSonic PJD7333 User manual

PJD8333s/PJD8633ws/PJD7333/

PJD7533w

DLP Projector

User Guide

Model No. VS14946/VS14935/VS14948/VS14950

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu

idadosamente las instrucciones en este manual”

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the follow-

ing two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy, and

if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modications not expressly approved

by the party responsible for compliance could void your authority to operate the

equipment.

For Canada

yThis Class B digital apparatus complies with Canadian ICES-003.

yCet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

CE Conformity for European Countries

The device complies with the EMC Directive 2004/108/EC and Low Volt-

age Directive 2006/95/EC.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic

Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment

including any spent or discarded batteries or accumulators as unsorted

municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment,

display the chemical symbol Hg, Cd, or Pb, then it means that the battery

has a heavy metal content of more than 0.0005% Mercury or more than,

0.002% Cadmium, or more than 0.004% Lead.

i

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

or other devices (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade and the third

prong are provided for your safety. If the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs.

Convenience receptacles and the point where they exit from the unit. Be sure

that the power outlet is located near the unit so that it is easily accessible.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the unit. When a cart is used, use

caution when moving the cart/unit combination to avoid injury from

tipping over.

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is

damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed

to rain or moisture, or if the unit does not operate normally or has been dropped.

ii

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive

2011/65/EU of the European Parliament and the Council on restriction of the use of

certain hazardous substances in electrical and electronic equipment (RoHS2 Direc-

tive) and is deemed to comply with the maximum concentration values issued by the

European Technical Adaptation Committee (TAC) as shown below:

Substance Proposed Maximum

Concentration Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex of

the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in compact uorescent lamps not exceeding 5 mg per lamp and in other

lamps not specically mentioned in the Annex of RoHS2 Directive

2. Lead in glass of cathode ray tubes, electronic components, uorescent tubes, and

electronic ceramic parts (e.g. piezoelectronic devices)

3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by

weight or more lead)

Lead as an allotting element in steel containing up to 0.35% lead by weight, alumin-

ium containing up to 0.4% lead by weight and as a cooper alloy containing up to 4%

lead by weight

iii

Copyright Information

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks

of Microsoft Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered

trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association.

DPMS and DDC are trademarks of VESA.

PS/2, VGA and XGA are registered trademarks of International Business Machines

Corporation.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors

or omissions contained herein; nor for incidental or consequential damages resulting

from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves

the right to change product specications without notice. Information in this docu-

ment may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means,

for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information

as it becomes available, please visit your region section on ViewSonic’s website to

register your product online.

The ViewSonic CD also provides an opportunity for you to print the product

registration form. Upon completion, please mail or fax to a respective ViewSonic

office. To find your registration form, use the directory “:\CD\Registration”.

Registering your product will best prepare you for future customer service needs.

Please print this user guide and fill the information in the “For Your Records” section.

Your LCD displays serial number is located on the rear side of the display.

For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name: PJD8333s/PJD8633ws/PJD7333/PJD7533w

ViewSonic DLP Projector

Model Number: VS14946/VS14935/VS14948/VS14950

Document Number: PJD8333s/PJD8633ws/PJD7333/PJD7533w_UG_ENG

Rev. 1A 01-24-13

Serial Number: ________________________________________

Purchase Date: ________________________________________

Product disposal at end of product life

The lamp in this product contains mercury which can be dangerous to you and the

environment. Please use care and dispose of in accordance with local, state or

federal laws.

ViewSonic respects the environment and is committed to working and living green.

Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic

website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

iv

v

Notes on the AC Power Cord

AC Power Cord must meet the requirement of countries where you use this projector.

Please confirm your AC plug type with the graphics below and ensure that the proper

AC Power Cord is used. If the supplied AC Power Cord does not match your AC out-

let, please contact your sales dealer. This projector is equipped with a grounding type

AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety pur-

pose of this grounding type plug. We highly recommend using a video source device

also equipped with a grounding type AC line plug to prevent signal interference due to

voltage fluctuations.

For Australia and

Mainland China

For the U.S.A. and

Canada

For the U.K.

Ground

For Continental Europe

Ground

Table of contents

vi

Introduction ........................................................................................... 1

Projector Features ................................................................................................................................. 1

Package Contents .................................................................................................................................. 2

Projector Overview ................................................................................................................................. 3

Using the Product ................................................................................. 5

Control Panel ......................................................................................................................................... 5

Connection Ports ................................................................................................................................... 6

Remote Control ...................................................................................................................................... 8

Installing the Batteries .......................................................................................................................... 11

Remote Control Operation ................................................................................................................... 12

Connection .......................................................................................... 13

Connecting a computer or monitor ....................................................................................................... 14

Connecting Video source devices ........................................................................................................ 16

Playing sound through the projector .................................................................................................... 18

Operation ............................................................................................. 20

Powering On/Off the Projector ............................................................................................................. 20

Adjusting the Projector Height ............................................................................................................. 21

Adjusting the Projector Zoom and Focus ............................................................................................ 21

Adjusting Projection Image Size .......................................................................................................... 22

Locking control keys ............................................................................................................................ 24

Setting the presentation timer .............................................................................................................. 25

Menu operation .................................................................................................................................... 26

Controlling the projector through a LAN environment .......................................................................... 38

Controlling the projector through a web browser ................................................................................. 41

Displaying images through vsPresenter .............................................................................................. 46

Displaying pictures with a USB storage device .................................................................................... 49

Maintenance ........................................................................................ 61

Cleaning the Lens ................................................................................................................................ 61

Cleaning the Projector Housing ........................................................................................................... 61

Replacing the Lamp ............................................................................................................................. 62

Specifications ...................................................................................... 64

Dimensions .......................................................................................................................................... 65

Ceiling mount installation ..................................................................................................................... 65

Appendix .............................................................................................. 66

LED Indicator Messages ..................................................................................................................... 66

Compatibility Modes ............................................................................................................................. 67

Troubleshooting ................................................................................................................................... 68

RS-232 Command and Configuration .................................................................................................. 69

IR Control Code ................................................................................................................................... 72

1

Introduction

Projector Features

The projector integrates high-performance optical engine projection and a user - friendly

design to deliver high reliability and ease of use.

The projector offers the following features:

• Single chip 0.55" Texas Instruments DLP® technology

• PJD7333 / PJD8333s: XGA (1024x768 pixel)

• Single chip 0.65" Texas Instruments DLP® technology

• PJD7533w / PJD8633ws: WXGA (1280x800 pixel)

• Compatibility with Macintosh® computers

• Compatibility with NTSC, PAL, SECAM and HDTV

• D-Sub 15-pin terminal for analog video connectivity

• User-friendly, multi-language on-screen display

• Advanced electronic keystone correction

• RS-232 connector for serial control

• HDMI 1.4a support

• PJLinkTM compatible

• Support remote control with Crestron software

• LAN display 4-1 (maximum 4 PC/ NB / smart phone / smart Pad display to 1

projector)

• USB display supports computer connection via USB mini-B type to A type cable

• Support USB flash drive for Photo / Video / music playback and office viewer

function

• DynamicEco Timer function decreasing the power consumption of the lamp by up to

70% when no input signal can be detected for a set period of time.

• Selectable quick power off function

• Switchable normal and economic modes to reduce the power consumption

• Support 3D DLP link technology

• Less then 0.5w power consumption in standby mode.

Note

•The information in this manual is subject to change without notices.

•The reproduction, transfer or copy of all or any part of this document is not permitted

without express written consent.

•The apparent brightness of the projected image will vary depending on the ambient

lighting conditions, selected input signal contrast/brightness settings, and is directly

proportional to projection distance.

•The lamp brightness will decline over time and may vary within the lamp manufacturers

specifications. This is normal and expected behavior.

2

Package Contents

When you unpack the projector, make sure you have all these components:

Optional accessories

1. Ceiling mount kit

2. Replacement Lamp

3. VGA - Components adapter

Note

•Contact you dealer immediately if any items are missing, appear damaged, or if the unit

does not work.

•For maximum protection of the product, please save the original shipping carton and

packing materials and repack your product as it was originally packed at the factory if

you need to ship it.

PJD8333s/PJD8633ws

Projector

PJD7333/PJD7533w

Projector AC Power Cord

VGA cable (D-SUB to D-

SUB)

Remote Control (IR) & batteries

(AAA *2 PCS)

Projector Carrying Case

ViewSonic CD Wizard Quick Start Guide

3

Projector Overview

Front View

PJD8333s/PJD8633ws PJD7333/PJD7533w

1. Front IR remote control sensor 2. Elevator button

3. Elevator foot 4. Projection lens

5. Security bar 6. Speaker

7. Ventilation holes (intake) 8. Focus ring

9. Zoom ring 10. Control panel

11. Lamp cover 12. Ventilation holes (exhaust)

23

1

4

87

11

5

12

6

10

9

23

1

4

87

12

56

10

11

4

Rear View

Bottom View

Note

•This projector can be used with a ceiling mount for support. The ceiling mount is not

included in the package.

•Contact your dealer for information to mount the projector on a ceiling.

•When installing the unit, incorporate a readily accessible disconnect device in the fixed

wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a

fault should occur during operation of the unit, operate the disconnect device to switch

the power supply off, or disconnect the power plug.

1. Rear IR remote control sensor 2. AC power socket

3. Connection ports 4. Kensington lock

PJD8333s/PJD8633ws PJD7333/PJD7533w

1. Ceiling mount holes (M4*8) 2. Tilt-adjustment feet

1

23 4

1

2

5

Using the Product

Control Panel

1. Power (Power LED indicator)

Refer to “LED Indicator Messages”.

2. TEMP (Temperature LED indicator)

Refer to “LED Indicator Messages”.

3. LAMP (Lamp LED indicator)

Refer to “LED Indicator Messages”.

4. Keystone/Arrow keys ( /Up, /Down)

Manually correct distorted images resulting from an angled projection.

5. Four directional buttons

Use four directional buttons to select items or make adjustments to your selection.

6. ENTER

Enter to sub-menu and confirm the menu selection.

7. SOURCE

Display the source selection bar.

8. MENU/EXIT

Display or exit the on-screen display menus.

9. Power

Turn the projector on or off.

4

6

5

6

3 2 1

9

7 4

8

6

Connection Ports

1. AUDIO IN 2/MIC

Connect an audio output from video equipment / computer or Microphone to this

jack.

Note: The function for switching to Audio in / Microphone in is in OSD menu.

2. AUDIO IN 1

Connect an audio output from video equipment or computer to this jack.

Note: AUDIO IN 1 jack can only play the sound from COMPUTER IN 1 signal.

3. S-VIDEO

Connect S-Video output from video equipment to this jack.

4. COMPUTER IN 1

Connect image input signal (analog RGB or component) to this jack.

5. MONITOR OUT

Connect to a computer display, etc.

6. HDMI

Connect HDMI output from video equipment to this jack.

7. RS-232

When operating the projector via a computer, connect this to the controlling com-

puter's RS-232C port.

8. TYPE B USB

This connector is for firmware update and mouse function support.

9. LAN

RJ45 connector for Ethernet connection.

12345 6 78 9

10

1112

131415

7

10. TYPE A USB

This connector supports USB flash drive and wireless dongle.

11. MINI USB

USB display supports computer connection via USB mini-B type to A type cable.

12. COMPUTER IN 2

Connect image input signal (analog RGB or component) to this jack.

13. VIDEO

Connect composite video output from video equipment to this jack.

14. DC 12V OUT

12V DC out

15. AUDIO OUT

Connect to a speaker or other audio input equipment.

8

Remote Control

1. Power

Turn the projector ON or OFF.

2. VGA

Switch between the COMPUTER IN 1 and COMPUTER IN 2 signal.

3. Auto Sync

Automatically determines the best picture timings for the displayed image.

4. Keystone/Arrow keys ( /Up, /Down)

Manually correct distorted images resulting from an angled projection.

5. Left

When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys

are used as directional arrows to select the desired menu items and to make

adjustments.

6. My Button

User definable key for customized function

7. Menu

Display or goes back to previous OSD menu.

8. Right mouse

Perform the right button of the mouse when mouse mode is activated.

9. Left mouse

Perform the left button of the mouse when mouse mode is activated.

10. Mouse

Switch between the normal and mouse modes.

11. Lock

Activate panel key lock.

4

5

7

9

11

12

10

3

8

6

4

13

14

15

16

17

18

19

24

25

20

21

29

22

23

26

28

27

9

12. Pattern

Display embedded test pattern.

13. Blank

Hide the screen picture.

14. D.Eco

Decreases the power consumption of the lamp by up to 70%.

Note: It takes some time to initiate this function. Make sure the projector has been

turned on for more than 4 minutes.

15. Laser

Aim the remote at the viewing screen, press and hold this button to activate the

laser pointer.

16. Source

Display the source selection bar.

17. Video

Switch input source to Composite/S-Video/HDMI by sequence.

18. Color Mode

Select the picture setup mode.

19. Enter

Confirmed selections.

20. Right

When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys

are used as directional arrows to select the desired menu items and to make

adjustments.

21. Exit

Exits and saves menu settings.

22. Page Up

Perform page up function when mouse mode is activated.

23. Page Down

Perform page down function when mouse mode is activated.

24. Magnify

Magnifies the projected picture size.

25. Volume

Adjust the volume level.

26. Freeze

Freeze the projected image.

27. Mute

Toggles the projector audio between on and off.

28. Aspect

Select the display aspect ratio.

29. Timer

Activate Presentation Timer OSD menu.

10

Operating the Laser pointer

The laser beam is visible. It is necessary to press and

hold LASER for continuous output.

The laser pointer is not a toy. Parents should be mindful of

the dangers of laser energy and keep this remote control

out of the reach of children.

Caution

•Do not look into the laser light window or shine the laser light beam on yourself or

others. See the warning messages on the back of the remote control prior to using it.

Using the remote mouse control

The capability of operating your computer with the remote control gives you more

flexibility when delivering presentations.

1. Connect the projector to your PC or notebook with a USB cable prior to using the

remote control in place of your computer’s mouse. See "Connecting a computer"

on page 14 for details.

2. Set the input signal to COMPUTER IN 1 or COMPUTER IN 2.

3. Press Mouse on the remote control to switch from the normal mode to the mouse

mode. An icon appears on the screen to indicate the activation of the mouse

mode.

4. Perform the desired mouse controls on your remote control.

• To move the cursor on the screen, press / / / .

• To left-click, press .

• To right-click, press .

• To operate your display software program (on a connected PC) which responds

to page up/down commands (like Microsoft PowerPoint), press Page Up/Page

Down.

• To return to the normal mode, press Mouse again.

11

Installing the Batteries

1. Open the battery cover in the

direction shown.

2. Install batteries as indicated by the

diagram inside the compartment.

3. Close the battery cover into position.

Caution

•Risk of explosion if battery is replaced by an incorrect type.

•Dispose of used batteries according to the instructions.

•Make sure the plus and minus terminals are correctly aligned when loading a battery.

Note

•Keep the batteries out of the reach of children. There is a danger of death by

accidentally swallowing the batteries.

•Remove batteries from remote control when not using for extended periods.

•Do not dispose of the used batteries along with household waste. Dispose of used

batteries according to local regulations.

•Danger of explosion may happen if batteries are incorrectly replaced. Replce all the

batteries with new ones.

•Batteries should not be in or near to fire or water, keep batteries in a dark, cool and dry

place.

•If suspect battery leakage, wipe out the leakage and then replace new batteries.

•If the leakage adheres to your body or clothes, rinse well with water immediately.

12

Remote Control Operation

Point the remote control at the infrared remote sensor and press a button.

• Operating the projector from the

front

• Operating the projector from the

rear

Note

•Do not point the laser directly to the people's eyes (especially small children). There is a

danger of injury to the eyes.

•The remote control may not operate when there is sunlight or other strong light such as

a fluorescent lamp shining on the remote sensor.

•Operate the remote control from a position where the remote sensor is visible.

•Do not drop the remote control or jolt it.

•Keep the remote control out of locations with excessively high temperature or humidity.

•Do not get water on the remote control or place wet objects on it.

•Do not disassemble the remote control.

13

Connection

When connecting a signal source to the projector, be sure to:

1. Turn all equipment off before making any connections.

2. Use the correct signal cables for each source.

3. Ensure the cables are firmly inserted.

Important

•In the connections shown above, some cables may not be included with the projector

(see "Package Contents" on page 2). They are commercially available from electronics

stores.

•The connection illustrations above are for reference only. The rear connecting jacks

available on the projector vary with each projector model.

•For detailed connection methods, see pages 14-17.

1. VGA cable (D-Sub to D-Sub) 2. VGA to DVI-A cable

3. USB cable (mini-B type to A type) 4. Audio cable

5. VGA (D-Sub) to HDTV (RCA) cable 6. S-Video cable

7. Composite Video cable 8. HDMI cable

9. USB flash drive 10. Microphone 3.5 mini jack cable

7

1

1234

54678

10

4

1

9

Page is loading ...

ViewSonic PJD7333 User manual

ViewSonic PJD7333 User manual

Related papers

Other documents