UFO HR-H1 Operating instructions

Brand
UFO
Model
HR-H1
Type
Operating instructions
LED MODE
ON/OFF
MOTOR
TIMING INDICATOR
PROJECTION
LED
ON/OF
Motor
LED
PROJECTION
After the main switch is turned on, press to turn
off the light and press to turn on the light.
After the main switch is turned on, press and hold to
change the color (cycling)Turn off the LED atmosphere
light, and single press to turn on the LED atmosphere light.
Press Open and forward, then reverse, then close.
cycle（Default is off）.
Press the boot button, and all functions will be opened by
default (except the motor) after the boot.The default setting
is 2 hours automatic shutdown. Short press the button
again to turn off the machine.
Remote control function
Function keys
Product parameters
Model
HR-H1
USB length
Product Size 180 m m x 180 m m x 85m m
1.8M
Optimal projection distance
Single gross weight
Operating temperature
Rated input
Shell material ABS
5V/2A
10℃～60℃
550g
2-2 . 5m
1. Do not disassemble the product under any
circumstances. There are no repairable parts inside
the product
2.Make sure your local power outlet matches the
voltage required for your device (USB DC 5V/2A)
3.Do not operate this product when the power cord
has been worn or broken
4.This product should be kept away from heat
sources, such as radiators, heat registers,
stoves or other electrical appliances that
generate heat.
Important security information
ON/ O FF
There are three levels of brightness. the
default brightness is the middle level.with each
press, the brightness increases one step.
There are three levels of brightness. the
default brightness is the middle level.with each
press, the brightness decreases one step.
B -
B +
Speed is divided into 0-1-2- gear, 0 gear is the slowest,
2 gear is the fastest,the default gear is 1, and the
speed decreases one gear at a time.
S -
Speed is divided into 0-1-2- gear, 0 gear is the
slowest, 2 gear is the fastest,the default gear
is 1, increasing one gear at a time.
S +
Press Open and forward, then reverse,
then close. cycle，（Default is off）.
After the main switch is turned on, simply press
to turn off the LED atmosphere light.Single
press to turn on the LED ambient light.
Single press to switch the color of
atmosphere lamp (colorful switching cycle)
W
The timing function is divided into two levels, namely
45-minute timing/90-minute timing. Press the first
time, the timing indicator lights up in blue, and enter
the 45-minute timer; press the second time, the timer
indicator lights red, and enters the 90-minute timer;
in the timing state, the timer indicator light stays on;
press and hold to cancel the timer, after canceling
The timing indicator light goes out.
Res e t Click to return to the boot mode
Time switch
ON/OF
MO
LED
After the main switch is turned on, press to turn
off the light and press to turn on the light
Projection switch
Atmosphere
light button
Motor switch
Main switch
Speed+
Speed-
Brightness -
Brightness +
Time switch
Reset
Atmosphere lamp
mode
UFO Projector
Angle adjustment feet
Slideshow slide slot
Focusing Wheel
Slideshow
Slideshow tray
Power jack
Manually rotate the focusing wheel to change the lens focus
for clear projection
Focusing
Product manual
Film installation
Pull out a slide slot; Choose your favorite slide,
Align the straight edge of the projection with the straight
edge in the mounting slot,
Then put into the installation slot; Install the projection
slot back into place.
After drawing out the projection film slot, it can be directly turned
90 ° to 180 °,make the projector fall out of the installation slot.
Film disassembly
240*120mm 二折三页
  • Page 1 1

UFO HR-H1 Operating instructions

Brand
UFO
Model
HR-H1
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents