EKR B1144 User manual

Brand: EKR

Model: B1144

Type: User manual

EKR B1144 is a Bluetooth LED name badge that allows you to display messages, animations, and even your own drawings on its screen. With its long battery life and easy-to-use app, it's perfect for parties, events, and even everyday use.

Product appearance and accessories

Operation Introduction

picture 1 picture 2

Step 1 Downloap App

Step 2 Prepare to connect

Install “Mini LedShow” in App Store for iOS device (picture 1)

1. Press Power/bluetooth button(a) to power on

2. Turn on bluetooth on your cellphone.

3. Run app, click “setting” and select “Device Connection”

(picture 3) to connect EKR led name badge.

or in Google Play for android device (picture 2)

Product Specifications

Battery Capacity: 320 mAh

Recharging Time: 5V/1A 3 h; 5V/2A 1.5 h

Size: 3.6 inch x 1.2 inch x 0.28 inch

Weight: 27 g

Operating temperature: 32 °F ~ 104 °F

Storage temperature: -13°F ~ 113 °F

Relative humidity: 0% ~ 90%

Package list: 1x Led name badge

1x USB charging cable

1x Megnetic pin

1x Hook & loop tape

1x Badge bar pin

1x Manual

picture 3 picture 4 picture 5

Operation Introduction

Step 3 Edit and synchronize messages

1. Seclect “light” icon (picture 4) to edit message

2. Pattern: 10 animations were preinstalled, Perfect for party.

3.Text: Type“+” to create one or more messages. It will appear

4. Graffiti: You can create your own pictures by seclecting pixels.

5. Rhythm: LED namebadge will beat with music (picture 5) in the

list or beat with surrounding music when click microphone

icon on lower right.

on name badge in 3 seconds. You can also adjust scrolling mode,

brightness and speed.

For more information please contact

[email protected]

Shanghai YiZhi Technology Co.,Ltd

Cautions

1. After fully charged, please cut off power in time to help

are forbidden and please maintain safe charging operation.

2. Over-powered chargers (Eg: 9V/2A, 12V/2A, 5V/3A, etc)

3. Do not use the badge while it is being charged.

4. Do not expose the namebadge to rain or in moisture.

protecting battery life.

b. Charging port

c. Megnetic pin

d. Hook & loop tape

e. Badge bar pin

f. USB charging cable

EKR Bluetooth LED Name Badge

Operation Manual

e f

a. Power / bluetooth button

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

· Reorient or relocate the receiving antenna.

· Increase the separation between the equipment and receiver.

· Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

· Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device

can be used in portable exposure condition without restriction.

EKR B1144 User manual

EKR B1144 User manual

Other documents