ekwb EK-Vardar X3M 120ER Installation guide

Brand
ekwb
Model
EK-Vardar X3M 120ER
Type
Installation guide
USER GUIDE
EK-Vardar
X3M 120ER
This product is intended for installation by expert users only. Please
consult with a qualified technician. Improper installation may result
in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products or
their installation. The following instructions are subject to change
without notice. Please, read the manual carefully before beginning
with the installation process.
- 3 -
TABLE OF CONTENT
INSTALLING THE FAN ON THE RADIATOR 4
EK-COOLSTREAM / EK-COOLSTREAM CLASSIC RADIATOR 4
EK-QUANTUM SURFACE RADIATOR 4
INSTALLING THE FAN DIRECTLY 5
REPLACING THE RUBBER CORNERS (DAMPERS) 5
CONNECTING THE FANS 6
SUPPORT AND SERVICE 8
SOCIAL MEDIA 8
- 4 -
INSTALLING THE FAN ON THE RADIATOR
EK-QUANTUM SURFACE RADIATOR
In the case of using the EK-Quantum Surface radiators, it is
mandatory to select the M4 x 10 DIN7985 Screws (https://www.
ekwb.com/shop/ek-loop-phillips-head-screw-set-m4x10mm-black-
20pcs) to secure the fan-s.
Use the Phillips Head Screwdriver to tighten the screws in a clockwise
direction. Don’t use excessive force while tightening the screws.
M4 x 10 DIN7985
SCREW
EK-VARDAR X3M 120ER
EK-COOLSTREAM / EK-COOLSTREAM CLASSIC
RADIATOR
Take the four encosed UNC 6-32 x 10 (10 mm long) screws for each
fan and screw them in. The number of enclosed screws depends
on the radiator model. Use the enclosed Allen key to tighten the
screws in a clockwise direction. Don’t use excessive force while
tightening the screws.
UNC 6-32 x 10
SCREW
EK-VARDAR X3M 120ER
- 5 -
INSTALLING THE FAN DIRECTLY
Using the enclosed mounting screws and thumb nuts you can mount
the EK-Vardar X3M fan directly to your chassis or any other standard
fan mounting location.
UNC
6-32 x 10
THUMB
NUT
REPLACING THE RUBBER CORNERS (DAMPERS)
STEP 1
First unscrew pre-installed M4 screws and thumb nuts using Allen
key (as shown on the photo). Carefully take off the rubber corner and
save the screws and nuts for later use.
STEP 1
M4 SCREW
M4 THUMB
NUT
CONNECTING THE FANS
STEP 1
To connect the fans you might need EK-Cable Y splitter.
Connect the female connectors from the fans with male connectors
on the fan splitter cable.
STEP 1
- 6 -
STEP 2
STEP 2
New dampers need to be secured with M4 screws and Thumb nuts.
Don’t use excessive force while tightening the screws.
- 7 -
STEP 2
Connect the female EK-Cable Y splitter connector to the male
connector header located on the motherboard. Always use CPU-
dedicated fan headers if possible.
Always use CPU fan header. On majority of motherboards
these headers usually offer best PWM regulation.
STEP 2
FAN HEADER
For assistance please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA
discord.gg/zesFRJB
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ekwb EK-Vardar X3M 120ER Installation guide

Brand
ekwb
Model
EK-Vardar X3M 120ER
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents