Page is loading ...
INTRODUCTION
This addendum should only be read
after you become familiar with the
basic programming functions of the
EazyR-2 remote in the main owner’s
manual. This assumes you are then
familiar with the basic setup proce-
dure for entering Library Codes and
the procedure for learning IR codes.
IR LIBRARIES & OVERLAYS
We have included special IR code
libraries and overlays for the
SoundSource and Eazy6 in our new
EazyR-2 remote.
The EazyR-2 comes with both sets of
codes installed in its library. The AMP
Source button is the button that you
would normally use for either the
SoundSource or the Eazy6.
The factory default under the AMP
button is the SoundSource Code Set
(# 0839), which can be changed to
the Eazy6 Code Set (# 1114). More
on how to accomplish this later.
Three overlays for the lower 12 buttons
are included: 1 for the SoundSource, 1
for the Eazy6, and a blank overlay. (See
Figure 1)
SpeakerCraft
®
OWNER’S MANUAL
ADDENDUM
EazyR-2
EZ Learning Remote Control
SoundSource Overlay
Eazy6 Overlay
Blank Overlay
Figure 1
LOCKING/UNLOCKING
IR LIBRARIES
The EazyR-2 remote comes fac-
tory defaulted (and locked) to the
SoundSource Code Set under the
AMP button. All other sources are
available for use with any of the
installed IR libraries or the IR codes
can be individually learned.
A Source button (i.e., AUX, CBL,
VCR, TV, SAT, CD, AMP, or TNR)
and its associated library can be
Locked or Unlocked for Code Set
changes as follows:
Press a Source button -> then SETUP
-> then 9 - 8 - 2.
This is a toggle function so it will alter-
nate from Locked to Unlocked each
time you go through the SETUP ->
then 9 - 8 - 2 sequence. The LED will
blink twice when locked and 4 times
when unlocked.
For example: If you want to unlock
the fixed, factory default for the AMP
button, which is the SoundSource,
you would:
Press the AMP button -> then
SETUP -> then 9 - 8 - 2. The LED
should blink 4 times indicating that
it is unlocked and can then be pro-
grammed with any other Library
Code Set. Follow the setup procedure
in the main owner’s manual.
To change it to the default Eazy6
Code Set however, additional steps
are required after the unlock steps
above.
IR LIBRARY CONFIRMATION
Anytime that you want to confirm
what library code group is under a par-
ticular Source button, do the following:
Push the Source button -> SETUP
(two blinks) -> 9 - 9 - 0 (two blinks)
-> 1 (count blinks) -> 2 (count blinks)
-> 3 (count blinks) -> 4 (count blinks).
The number of blinks after pressing
each digit represents the 4 digit code
for that particular Source button
DEFAULT RESET
There is a reset sequence that
you can use to restore everything
not related to IR Code Set assign-
ments, back to the factory defaults.
Reassignments you may have done
of SpeakerCraft Code Sets using the
SETUP -> then 9 - 8 - 7 sequence
are not affected.
Push the SETUP button -> 9 - 8 - 0.
The LED will flash 2 times, pause, and
then 2 more times to confirm a suc-
cessful reset.
CAUTION: Enter these numbers
exactly as shown. Otherwise, you
can erase part of the library if another
set of numbers is entered.
BASIC USER RESET
This reset is similar to the above,
except it clears all user code assign-
ments, including SpeakerCraft Code
Sets, and returns everything back to
basic factory defaults.
Push the SETUP button -> 9 - 7 - 7.
The LED will flash 2 times, pause, and
then 2 more times to confirm a suc-
cessful reset.
Note: To restore the SpeakerCraft
Code Sets, use the SETUP -> then 9 -
8 - 7 sequence explained previously.
CAUTION: Be careful when using
these Resets. You could erase a lot of
work, including learned commands.
CUSTOMER SERVICE
For technical inquires, please call
1-800-448-0976 or e-mail us at
techsupport@speakercraft.com. We are
available to assist you every weekday,
except holidays, between the hours of
7:00 a.m. and 5:00 p.m. PST.
SpeakerCraft offers a variety of acces-
sories to make your installation of these
speakers and other SpeakerCraft prod-
ucts easy, economical, and professional.
Contact your authorized SpeakerCraft
Dealer for more information.
Source Available IR
Button Code Library
TV TV
VCR VCR, DVD, Cassette,
LDP, DAT
CBL Cable, Video Accessories,
Satellite, DSS
SAT Satellite, DSS, Cable,
Video Accessories
AMP Amp, Tuner, Phono,
Misc. Audio, CD,
Home Automation,
MD, SpeakerCraft
TNR Tuner, Amp, Phono,
Misc. Audio, CD,
Home Automation,
MD, SpeakerCraft
CD CD, Home Automation,
MD, Amp, Tuner, Phono,
Misc. Audio, SpeakerCraft
AUX DVD, LDP, VCR, Cassette,
SpeakerCraft
940 Columbia Avenue, Riverside, CA 92507
(800) 448-0976 Fax (909) 787-8747
www.speakercraft.com
SpeakerCraft
®
LIT06005
Press the AMP button -> then SETUP
-> then 9 - 8 - 7 (red LED blinks
twice) -> then 1 - 1 - 1 - 4 (red LED
blinks twice). Note: The code assign-
ment automatically locks after this
sequence.
You can also place the Eazy6 Code
Set, or the SoundSource Code Set,
under any of the other Source but-
tons as well. Simply follow the same
procedures as given above, using
Source buttons and SpeakerCraft
Code Sets, as desired.
MAPPING IR LIBRARIES
The table below indicates the “map-
ping” of the various IR code libraries
and what source keys can be used for
IR code libraries other than the ones
that are labeled with the Source but-
ton text.
For instance, a DVD’s IR code library
can be assigned to the VCR or the
AUX source buttons.
Through some very flexible program-
ming, the installer is not limited to just
using the above mentioned source
buttons and their respective code
libraries. You can reassign a source
button’s code library to another
source button.
For instance, if you are not using the
Cable (CBL) button, and you want
another button to place the DVD IR
code library, you can reassign the Aux
mapping (which contains the DVD
library) to the Cable button as follows:
Push the SETUP button -> 9 - 9 - 2
- AUX - CBL. The LED will flash twice
to indicate a successful reassignment.
You can now use the Cable button
for any of the Aux mapped IR code
libraries.
/