Page is loading ...
CLAMPING BENCH SYSTEM
When using the EZ SMART Clamping Bench System with any power tool, be sure you have read and
understand the operating manual for the tool before operation. Be sure to use the tool safely. Do not
disable any built-in safety features. Be sure to follow safe practices when using the EZ SMART Clamping
Bench System with your power tools. If a task seems like it might be potentially unsafe, do not attempt. Do
not operate any tool with the EZ SMART Clamping Bench System if you are tired or distracted in any way.
http://www.eurekazone.com/category_s/1995.htm
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone (352) 620-2262 Fax (352) 620-2576 Techsupport@eurekazone.com www.eurekazone.com
V15-01
Parts List
Part A (2) 48.25” SSME Side Rails
Part B(2) 22.5” SSME End Rails
Part C(2) 14.125” End Support Brackets
Part D(2) 14.125” End Support Connectors
Part E(2) 38.25” Side Support Brackets
Part F(2) 38.25” Side Support Connectors
Part G(22) 5/16-18 x 3/4” Hex Screws
Part H(4) 34” SME Legs
Part I(1) Frame Brace w/ Hardware
Part J(2)23.75” T-Track Leg Braces w/ Hardware
Part K(4) Feet with Connectors
Part L(2) Corner Sets with Connectors
Part M(1) Clamping Top
Part N(36) #8 x 3/4” Pan Head Screws
Page 1
M
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone (352) 620-2262 Fax (352) 620-2576 Techsupport@eurekazone.com www.eurekazone.com
FRAME ASSEMBLY
The first stage of assembly involves putting together the bench frame. The diagrams for each step show the
frame in the upright position but for ease of assembly it may be assembled upside down on a workbench. The
following is the list of parts needed to assemble the bench frame:
(2) – 48.25” SSME Side Rails Part A
(2) – 22.5” SSME End Rails Part B
(2) – Corner Sets With Connectors Part L
(2) – 38.25” Side Support Bracket Part E
(2) – 38.25” Side Support Connector Part F
(2) – 14.125” End Support Bracket Part C
(2) – 14.125” End Support Connector Part D
(22) – 5/16-18 x 3/4” Hex Bolts Part G
Step 1
Assembly of the bench frame begins with one corner, one end rail, and one side rail. Loosen the connectors
on the corner bracket. The face of the corner with the horizontal connector and the vertical connector
corresponds to the side of the bench frame. The face of the corner with only the horizontal connector
corresponds to the end of the bench frame. Insert the 22.5” SSME End Rail (Part B) onto the corner
connector(Part L). Then insert the 48” SSME Side Rail (Part A) onto the corner connector (Part L). The Side
Rail (Part A)overlaps the End Rail(Part B) by 3/4” as shown in the diagrams. Tighten all of the nuts with a 1/2”
nut driver or wrench.
Step 2
Attach the Support Connectors (Part E) to the Support Brackets (Part F) using the included hex screws(Part G).
Do not tighten the screws so the connector remains loose for the next step.
V15-01
Page 2
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone (352) 620-2262 Fax (352) 620-2576 Techsupport@eurekazone.com www.eurekazone.com
FRAME ASSEMBLY (cont)
Step 3
Step 4
Slide the End Support Bracket (Part C) and Connector (Part D) unit into the End Rail (Part B)until the Bracket
touches the Corner. Snug, but do not yet fully tighten the 1/2” hex screws (Part G). Slide the Side Support
Bracket (Part E)and Connector (Part F) unit into the Side Rail (Part A)until the Bracket (Part C) touches the
Corner. Snug, but do not yet fully tighten the 1/2” hex screws (Part G).
Repeat the above assembly steps for the diagonally opposite corner with the remaining End Rail (Part B) and
Side Rail(Part A).
Step 5
The two assembled Corner-Rail units will now be joined together with the two remaining Corners. Be sure
that the vertical connectors on the Corners are facing the sides of the bench frame. The Side Rails (Part A) will
overlap the End Rails (Part B) as in Step 1.
2
nd
Corner-Rail unit
1
st
Corner-Rail unit
V15-01
Page 3
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone (352) 620-2262 Fax (352) 620-2576 Techsupport@eurekazone.com www.eurekazone.com
LEG ASSEMBLY
Step 1
The second stage of assembly involves attaching the legs to the assembled bench frame. If the frame was
assembled upright it may be easier to turn the frame over to assemble the legs. The following is the list of
parts needed for adding the legs:
(4) 34” SME Legs (Part H)
(4) Feet with Connectors (Part K)
(2) 24” T-Track Leg Braces with Hardware (screws, washer, and insert) (Part J)
Install each SME Leg (Part H) onto the vertical connector on each Corner (Part L). The leg must rest against the
lip on the SSME Side Rails(Part A). Tighten all nuts with a 1/2” nut driver.
(Part H)Leg
against the lip of
the Side Rail
(Part A)
Step 2
Next, the Leg Braces (Part J) will be installed between the Legs at each
end of the bench frame. The Leg Braces come with the hardware pre-
installed. Loosen the screw and slide the T-nuts at each end into the
outer edge channel of SME Leg. Be sure that the lip on the Leg Brace
is toward the top of the table, this allows for the ability to add an
optional shelf. Locate the Leg Brace 8” from the bottom of the Legs.
Tighten the screws.
Step 3
The final step is to install the feet on the legs (Part K).
Loosen the nut and slide the connector into the bottom of
the SME Leg (Part H). Tighten the nuts. Turn the bench
over. The feet are adjustable to account for any floor
irregularities. Make any necessary adjustments.
Bottom of Leg
V15-01
Page 4
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone (352) 620-2262 Fax (352) 620-2576 Techsupport@eurekazone.com www.eurekazone.com
COMPLETING THE BENCH
Before installing the Clamping Bench Top, take some time to verify the dimensions between the Side Rails
(Part A) and between the End Rails (Part B). The interior dimension between the Side Rails should be 24”. The
interior dimension between the End Rails should be 48”. Make any necessary adjustments at the corners.
24”
48”
Step 1
Attach the Clamping Bench Top to the End and
Side Supports with the included #8 x 3/4” pan
head screws (Part N).
Step 2
The final step in the assembly of the
Clamping Bench is to attach the Frame
Brace (Part I) using the included
hardware. Remove the hardware from
the Frame Brace and insert the head of
the bolt into the bottom channel of each
Side Rail toward the middle of the table.
Slide the Frame Brace over the bolt
followed by the washer and the nut.
Tighten the nuts to secure the Frame
Brace.
V15-01
Page 5
/
