DKS DKS Reverse Edge User manual

Brand: DKS

Model: DKS Reverse Edge

Type: User manual

DKS DKS Reverse Edge

The DKS Reverse Edge is a monitored reversing edge that provides external entrapment protection for motorized vehicular doors and gates. It meets 2018 UL 325 standards for a type B2 contact sensor device and sends a signal to stop and/or reverse gate operation when encountering an obstruction.

This edge is designed to be used with wireless or hardwired gate applications and can be wired at the end-of-line in a series with four-wire edges.

Features:

Monitored resistive edge provides external entrapment protection
Meets 2018 UL 325 standards for a type B2 contact sensor device

DKS DKS Reverse Edge

This edge is designed to be used with wireless or hardwired gate applications and can be wired at the end-of-line in a series with four-wire edges.

Features:

Monitored resistive edge provides external entrapment protection
Meets 2018 UL 325 standards for a type B2 contact sensor device

MONITORED REVERSING EDGE (2-WIRE END-OF-LINE)

Installation

DoorKing Part Numbers

8080-115-C-5-19

8080-100

5 ft length

8080-101

CAUTION: Read installation instructions before installing sensing edge.

The 8080 Series Sensing Edges operate on 30 volts AC/DC, 1/4 amp maximum. Overloading will decrease

the life of the product and could cause immediate failure of the edge or electrocution.

6 ft length

The 8080 Series Sensing Edge is designed to be used with motorized vehicular doors and gates only.

This monitored resistive edge provides external entrapment protection that meets 2018 UL 325 standards for a type B2 contact

sensor device. It sends a signal to stop and/or reverse gate operation when encountering an obstruction. This edge will work with

wireless or hardwired gate applications. When using this edge in series with four-wire edges, it gets wired at the END-OF-LINE in the

series.

Connect the sensing edge to the door/gate operator control board as specified by the door or gate operator manufacturer. Slide

aluminum track off of edge and mount it to the desired surface drilling enough holes in it as necessary to secure it to the surface

using appropriate hardware (not provided). Slide edge back onto track and run wire to: gate operator, wireless transmitter or to a

4-wire IN-LINE edge when series wiring edges together.

• Adjust the equipment to which the

sensing edge is attached so that the

edge is never compressed more

than 1/4”.

• Test the edge with the door/gate

closed. The edge should show an

open circuit. If the circuit is closed,

readjust the close limit (refer to

manufacturers installation manual)

so the edge circuit is open.

• IMPORTANT: Check the sensing

edge and wiring to insure the

sensing circuit is working

properly.

120 S. Glasgow Avenue

Inglewood, California 90301

U.S.A.

Use mason anchors,

metal screws, etc.

(not provided)

To Monitored Input

Drill enough

holes in

aluminum

track to secure

track to surface.

Aluminum Track

Typical OPEN Edge Location for a slide gate

Typical CLOSE Edge Location for a slide gate

Opening Gate

MONITORED Wireless

Edge transmitter

mounted on gate

(sold separately)

Note:

NEVER PAINT Sensing Edge

NEVER CUT OR PUNCTURE Sensing Edge

NEVER PULL ON WIRES

PERMANENT WIRING MUST BE EMPLOYEED AS REQUIRED BY LOCAL CODES. ALWAYS ADHERE

TO THE LOCAL AND NATIONAL ELECTRICAL CODE SPECIFICATIONS WHEN WIRING SENSING

EDGE AND OTHER CONTROLS.

DKS DKS Reverse Edge User manual

Brand: DKS

Model: DKS Reverse Edge

Type: User manual

DKS DKS Reverse Edge

This edge is designed to be used with wireless or hardwired gate applications and can be wired at the end-of-line in a series with four-wire edges.

Features:

Monitored resistive edge provides external entrapment protection
Meets 2018 UL 325 standards for a type B2 contact sensor device

Download PDF

report

DKS DKS Reverse Edge User manual

DKS DKS Reverse Edge User manual

Related papers

Other documents