Fypon LDCH58X18 User manual

Brand: Fypon

Model: LDCH58X18

Type: User manual

Fypon, Ltd. 1750 Indian Wood Circle Maumee, Ohio 43537 1.800.446.3040 www.fypon.com

Continued on next page

Page 1 of 2

Polyurethane Millwork - General Information

INSTALLATION INSTRUCTIONS

Storage & Handling

• Polyurethanemillworkshouldbestoredonaat,levelsurfaceinacool,shadedarea,andshouldnotbestoredinextremeheat.

• Millworkthathasbeenstoredinahotplaceshouldbeallowedtoacclimatetotheinstallationarea.Duetourethane'shighinsulatingvalue,

thismaytakeupto10hours.

• Handletheproductwithcaretoavoiddamage.Iftheproductdoesbecomedamaged,itiseasytorepair.Usewoodllerorautomotive

llertoquicklylldentsorgashesofanysize.Brokenmouldingcanbesuccessfullyrejoinedwithpolyurethanecompatibleadhesiveor

equivalentproduct.

Product Applications

• Fyponpolyurethaneproductsaretobeusedfordecorativepurposesonly,nottoprovidestructuralsupport(exceptstructuralcolumns,

balustradesystemsandporchposts).

• Fyponpolyurethaneproductscanwithstandtemperaturesofabout140°F(60°C).However,themillworkshouldneverbeinstalledinanarea

subjecttosolartemperaturebuildup,suchasbehindastormdoor.

• Fyponpolyurethanewillresisttheelements,exceptfordirectsunlighttotheyellowish(unpainted)undersideofthemillwork.Itisimportant

tolldamagedorcutsurfaceswithputty,caulk,and/orpaintwithinafewdays.

Machining Guidelines

• Fyponproductscanbecut,drilledorroutedsimilartowoodproducts.

Fastening Guidelines

• Properfasteningisimportantinlimitingtheeffectsofexpansionandcontractionontheproduct.Forbestresults,alwaysusenon-corrosive

nishnailsorscrewsincombinationwithurethanecompatibleAdhesiveorequivalentproduct.Adhesiveshouldbeappliedtoallcontact

points,includingjointends.

• Powernailersworkwellwiththisproductbutshouldbeadjustedtopreventoverdrivingthefastenerintothematerial.Thiswillprevent

excessivenailpressurewhichcanresultincracking.

Finishing Techniques

• Painting- Fyponproductsmaybepaintedwithanygoodqualitylatexpaint.Usuallyonecoatisallthatisneeded.Seeadditionalinformation

onnishingandpaintingbelow.Theyarealsosuitableformanyfauxnishingtechniques,includingsponging,featheringandantiquing.

• Staining-FyponTimberproductsarenotedasWoodgrain/Stainableandmaybestainedwithagoodquality,non-penetratingstain.Apply

stainwitha2"naturalbristlebrush.Beginwithacircularmotion,thenfeatherthestaininthedirectionofthegrain.Foradarkernish,

applyaheavycoatofstainwithlightpressure.Foralighternish,applyathincoatofstainwithmorepressure.

• GroutApplication-FyponStoneproductsdonotrequiregroutapplication,butitmaybeappliedafterinstallationtoachieveadesired

appearance.Aurethane-basedgroutisrecommendedandshouldbeappliedperthegroutmanufacturer'sspecications.

Expansion & Contraction

• Thisproductexpandsandcontractswithchangesintemperature.TominimizethischaracteristictherecommendationsgivenintheFastening

sectionshouldbefollowed.

• Wheninstallingthisproductallow

”per18’forexpansionandcontraction.Rememberthatitisrecommendedthatalljointsbegluedand

wherepossible,fastenedtothesubstratetopreventjointseparation.

Mouldedofhigh-densitypolyurethanefoam,Fyponmouldedproductshaveanin-mouldbarriercoat,whichbecomesanintegralpartoftheurethane

foamasitcures.Aftereachpieceismouldedandtrimmed,weapplyanexteriorgradeprimer.Polyurethaneisaclosed-cellproduct,makingitresistantto

moistureandinsects.Itresistsrotting,warpingcrackingandpeeling,aswellascrumblinganddeterioration.

General Installation Notes

Any adhesives, sealants, ﬁllers or paint used must be compatible with the material that is being installed (see manufacturer’s recommendations in the

Finishing and Adhesives section below). Always use corrosion-resistant mechanical nails or screws along with manufacturer’s recommended adhesive

product when installing all Fypon products. This combination provides a secure, long-lasting bond. Countersink all fasteners about

" and ﬁll with

product compatible ﬁller. Exterior installations should be ﬁnished using a manufacturer’s recommended caulk to prevent water inﬁltration behind

siding, windows and doors. Some exterior installations, in particular new construction before siding is applied, may require a J-channel and/or

ﬂashing to prevent water inﬁltration. Installers must determine which installation technique is best for the speciﬁc situation.

Finishing and Adhesives

Polyurethane (PUR) – Fypon polyurethane products are factory primed. Depending on product location, always use interior/exterior-grade, PUR

compatible adhesives, sealants, and ﬁllers when installing Fypon products. Consult the manufacturer’s recommendations for your particular

climate and the substrate you are installing to.

Cellular PVC – Depending on product location, always use interior/exterior-grade, PVC compatible adhesives, sealants, and ﬁllers when installing

Fypon products. Consult the manufacturer’s recommendations for your particular climate and the substrate you are installing to. If painting is

desired, a 100% acrylic latex paint with a Light Reﬂectance Value (LRV) of 55% or higher must be used. Applying paint with an LRV of 54% or

lower will void the warranty.

IMPORTANT:

Please read these installation guidelines thoroughly before beginning installation. Please note that these guidelines are provided only to assist with the installation of Fypon moulding

and millwork products. Modiﬁed procedures may be required in order to meet speciﬁc situations, unique applications and local building codes. The manufacturer does not, under any

circumstances, warrant the installation of its products. Be sure to wear appropriate protective clothing, gloves and safety glasses when working with any tools. Installer should check

for and relocate all electrical wiring within the proposed installation area, as needed (be sure to disconnect all electric power before working with any electrical wiring and follow all

applicable local electrical codes and safety procedures).

Fypon, Ltd. 1750 Indian Wood Circle Maumee, Ohio 43537 1.800.446.3040 www.fypon.com

Page 2 of 2

Polyurethane Millwork - General Information Continued