Philips FC9178/01 User manual

Page is loading ...

6



Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at www.philips.

com/welcome.

Philips incorporates the latest technologies to create products that are

good for the environment in terms of energy consumption as well as

material usage. This product is partly made of bioplastics and recycled

plastics. Parts made of bioplastics are environmentally friendly because they

have been derived from renewable biomass sources. Some parts still need

to be made of conventional plastics, but for these parts Philips tries to use

recycled plastics as much as possible. This production method results in

considerably less waste than the traditional method. For more information

on this and other environmental efforts of Philips, please visit www.

asimpleswitch.com.

The Green Performer’s extremely efcient motor yields a high

performance at a low power consumption.



 Cord rewind button

 Suction power selection wheel (specic types only)

 On/off button

 Dustbag-full indicator

 Hose connection opening

 Hose with swivel connection

 Cover release tab

 Motor protection lter holder

 Removable strip (specic types only)

 Reusable dustbag (specic types only)

 Dustbag holder

 Dustbag

 Rear wheels

 Ergonomic PostureProtect handgrip (specic types only)

 Tube release button

 Tube release button

 Accessory holder release levers

 Accessory holder

 Screw cover strip

 Hose

 Flexible hose connection

 Ergonomic ComfortControl handgrip (specic types only)

 Infrared remote control (specic types only)

 Telescopic tube without PostureProtect handgrip (specic types only)

 Telescopic tube with PostureProtect handgrip (specic types only)

 Tri-Active nozzle

 Rocker switch for carpet/hard oor settings

 Side brush

 Parking/storage ridge

 Small nozzle

 Crevice tool

 Brush attachment

 Hinging top handle

 Exhaust grille



 Parking slot

 Mains plug

 HEPA 13 washable lter

 Storage grip

 Swivel wheel

 Storage slot

 Type plate



Read this user manual carefully before you use the appliance and save it for

future reference.



- Never suck up water or any other liquid. Never suck up ammable

substances and do not suck up ashes until they are cold.



- Check if the voltage indicated on the appliance corresponds to the

local mains voltage before you connect the appliance.

- Do not use the appliance if the plug, the mains cord or the appliance

itself is damaged.

- If the mains cord is damaged, you must have it replaced by Philips, a

service centre authorised by Philips or similarly qualied persons in

order to avoid a hazard.

- This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety.

- Children should be supervised to ensure that they do not play with the

appliance.

- Do not point the hose, the tube or any other accessory at the eyes

or ears nor put it in your mouth when it is connected to the vacuum

cleaner and the vacuum cleaner is switched on.



- When you use the vacuum cleaner to vacuum ashes, ne sand, lime,

cement dust and similar substances, the pores of the dustbag become

clogged. As a result, the dustbag-full indicator will indicate that the

dustbag is full. Replace the disposable dustbag or empty the reusable

dustbag, even if it is not full yet (see chapter ‘Replacing/emptying the

dustbag’).

- Never use the appliance without the motor protection lter. This could

damage the motor and shorten the life of the appliance.

- Only use Philips s-bag ` synthetic dustbags or the reusable dustbag

provided (some countries only).

- Noise level: Lc = 78 dB(A)



This Philips appliance complies with all standards regarding electromagnetic

elds (EMF). If handled properly and according to the instructions in this

user manual, the appliance is safe to use based on scientic evidence

available today.

 7



1 Take the appliance and its accessories out of the box.

2 Remove any sticker, protective foil or plastic from the appliance.



Batteries for the remote control are supplied with the appliance. Insert the

batteries into the battery compartment in the ergonomic handgrip before

you use the appliance. The batteries last at least 2 years.

1 Use a screwdriver to loosen the screw of the battery compartment

lid (1) and remove the battery compartment lid (2).

2 Insert two AAA 1.5-volt alkaline batteries into the battery

compartment inside the handle.

Note: Make sure that the - and + poles point in the right direction.

3 Reattach the battery compartment lid (1) and fasten the screw with

a screwdriver (2).







- The unique ComfortControl handgrip is ergonomically designed to

give you sufcient comfort during vacuum cleaning.

- To gain optimal benet from this handgrip, it is important that you do

not position your second hand on the tube. When you do so, you twist

and bend your back, which could result in back problems.

8



- The unique PostureProtect handgrip is ergonomically designed for 2-

handed use to prevent you from placing your hand on the lower part

of the tube.We recommend that you use the PostureProtect handgrip

to prevent bending your back, but if you do not nd it comfortable to

use, you can remove it. In this case, follow the instructions in section

‘Removing the PostureProtect handgrip’ in chapter ‘Troubleshooting’.

- Do not place your other hand on the tube. You twist and bend your

spine when you do so, which could result in back problems.

- Our ergonomist advises you to adjust the length of the tube so that

the hand holding the standard handgrip is at hip level.



1 Attach the handgrip to the telescopic tube (‘click’).

2 To disconnect the handgrip from the tube, hold the handgrip with

one hand. With the other hand, hold the telescopic tube and press

the tube release button (1) and pull the tube off the handgrip (2).

Note: This vacuum cleaner has been tted with holes at the end of the

handgrip. These holes may prevent objects from getting stuck or damaged

when you use your vacuum cleaner without the tube or accessories supplied.



1 To connect the hose, push it rmly into the appliance (‘click’).

 9

2 To disconnect the hose, push the buttons (1) and pull the hose out

of the appliance (2).



1 Adjust the length of the tube in such a way that the exible hose

connection is at hip level.

2 Hold the tube so that the standard handgrip is at hip level.

3 To connect the tube to a nozzle, press the spring-loaded lock button

on the tube and insert the tube into the nozzle. Fit the spring-loaded

lock button into the opening in the nozzle (‘click’).

- To disconnect the nozzle from the tube, press the spring-loaded lock

button and pull the accessory out of the tube.

10



1 Slide the accessory holder with accessories onto the handgrip

(‘click’).

2 To detach the accessory holder, squeeze the release levers

together (1) and slide the accessory holder off the handgrip (2).



1 Connect the crevice tool (1) or small nozzle (2) with or

without brush attachment (3) to the tube or directly to the handgrip.



1 To assemble the brush attachment, slide it onto the bottom of the

small nozzle (‘click’).

2 To disassemble the brush attachment, slide it off the bottom of the

small nozzle.

3

 11



The Tri-Active nozzle is a multi-purpose nozzle for carpets and hard oors.

- The side brushes catch more dust and dirt at the sides of the nozzle

and allow you to clean better along furniture and other obstacles.

- The opening at the front of the nozzle allows you to suck up larger

particles.

1 Use the hard oor setting to clean hard oors (for instance for

tiled, parqueted, laminated and linoleumed ooring): push the rocker

switch on top of the nozzle with your foot to make the brush strip

come out of the housing. At the same time, the wheel is lifted to

prevent scratching and to increase manoeuvrability.

2 Use the carpet setting to clean carpets: push the rocker switch again

to make the brush strip disappear into the nozzle housing. The wheel

is lowered automatically.



- The remote control has three buttons with which you operate the

vacuum cleaner. With the ‘+’ and ‘-’ buttons you adjust the suction

power and with the standby button you switch the appliance to

standby mode.

Note: The functions on the remote control only work after you have switched

on the appliance with the on/off switch on the appliance itself.

Note: Replace the batteries when the ‘infrared active light’ does not light up

when you press any button. See chapter ‘Replacement’ to replace the batteries.

12



1 Pull the cord out of the appliance and put the mains plug in the wall

socket.

2 To switch on the appliance, press the on/off button on top of the

appliance.

Tip: To avoid bending your back, press the on/off button with your foot.

3 To switch off the appliance, press the on/off button on top of the

appliance.





1 During vacuum cleaning, you can adjust the suction power with the

selection wheel on top of the appliance.

- Use maximum suction power to vacuum very dirty carpets and hard

oors.

- Use minimum suction power to vacuum curtains, tablecloths etc.



1 During vacuuming, you can adjust the suction power level with the

– and + buttons on the remote control.

- Use maximum suction power to vacuum very dirty carpets and hard

oors.

- Use minimum suction power to vacuum curtains, tablecloths etc.

 13



1 If you want to stop vacuum cleaning for a moment, press the standby

button on the remote control to switch off the appliance temporarily

(specic types only).

If your appliance has no remote control, press the on/off button on top of

the appliance to switch off the appliance.

2 Insert the ridge on the nozzle into the parking slot to park the tube

in a convenient position.

3 To ensure stable parking of the telescopic tube, adjust the tube to

the shortest length.

4 To continue vacuum cleaning, simply press the standby button on the

remote control again (specic types only).

If your appliance has no remote control, press the on/off button on top of

the appliance to switch on the appliance.



1 Switch off the appliance and remove the mains plug from the wall

socket.

2 Press the cord rewind button to rewind the mains cord.

3 Put the appliance in upright position. To attach the nozzle to the

appliance, insert the ridge on the nozzle into the storage slot.

- To ensure stable parking of the telescopic tube, adjust the tube to the

shortest length.

4 Specic types only: Always put the Tri-Active nozzle in the carpet

setting when you store it. Also prevent the side brushes from

becoming bent.

14



Always unplug the appliance before you replace the disposable dustbag

or empty the reusable dustbag.



- Replace the dustbag as soon as the dustbag-full indicator has changed

colour permanently, i.e. even when the nozzle is not placed on the

oor.

1 Pull the cover upwards to open it.

2 Lift the dustbag holder out of the appliance.

Make sure you hold the dustbag upright when you lift it out of the

appliance.

3 Pull at the cardboard tag to remove the full dustbag from the holder .

, When you do this, the dustbag is sealed automatically.

 15

4 Slide the cardboard front of the new dustbag into the two grooves of

the dustbag holder as far as possible.

5 Put the dustbag holder back into the vacuum cleaner.

Note: If no dustbag has been inserted, you cannot close the cover.

6 Push the cover downwards to close it.



In some countries, this vacuum cleaner also comes with a reusable dustbag

that can be used and emptied repeatedly. You can use the reusable dustbag

instead of disposable dustbags.

To remove and insert the reusable dustbag, simply follow the instructions

in ‘Replacing the disposable dustbag’.

To empty the reusable dustbag:

1 Slide the clip off the dustbag sideways.

2 Shake out the contents into a dustbin.

3 To close the dustbag, slide the clip back onto the bottom edge of the

dustbag.



Always unplug the appliance before you clean or replace the lters.



Clean the permanent motor protection lter every time you empty the

reusable dustbag or replace the disposable dustbag.

1 Remove the dustbag holder with the dustbag.

16

2 Press the tab at the top of the motor protection lter holder

down to release it (1). Lift the lter holder out of the dustbag

compartment (2).

3 Shake the lter over a dustbin to clean it.

4 Put the clean lter back into the lter holder.

5 Fit the two lugs of the lter holder behind the ridge at the bottom

to ensure that it ts properly at the top (1). Then press the lter

holder home (‘click’) (2).

6 Place the dustbag holder with the dustbag back into the appliance

and close the cover.



HEPA 13 washable lter is able to remove 99.95% of all particles down to

0.0003mm in size from the outlet air. This not only includes normal house

dust, but also harmful microscopic vermin such as dust mites and their

excrements, which are well-known causes of respiratory allergies.

Note: To guarantee optimal dust retention and performance of the vacuum

cleaner, always replace the HEPA lter with an original Philips lter of the

correct type (see chapter ‘Ordering accessories’).

Clean the washable HEPA 13 lter every 6 months. You can clean the

washable HEPA 13 lter max. 4 times. Replace the lter after it has been

cleaned 4 times.

Note: Do not clean the HEPA 13 lter in the washing machine, but follow the

procedure below.

1 Hold the release tabs of the HEPA 13 lter to open and remove the

lter cover.

2 Take out the washable HEPA 13 lter.

3 Rinse the pleated side of the HEPA 13 lter under a hot slow-

running tap.

 17

- Hold the lter in such a way that the pleated side points upwards and

the water ows parallel to the pleats. Hold the lter at an angle so that

the water washes away the dirt inside the pleats.

- Turn the lter 180° and let the water ow along the pleats in opposite

direction.

- Continue this process until the lter is clean.

Never clean the washable lter with a brush.

Note: Cleaning does not restore the original colour of the lter, but does restore

its ltration power.

4 Carefully shake the water from the surface of the lter. Let the lter

dry completely for at least 2 hours before you put it back into the

vacuum cleaner.

5 Put the dry lter back into the appliance.

6 Reattach the top of the lter cover and then close the cover (‘click’)

(2).

18



For purchasing dustbags, lters or other accessories for this appliance,

please visit www.philips.com, consult the worldwide guarantee leaet or

contact the Philips Consumer Care Centre in your country.



- Philips Classic s-bag ` synthetic dustbags are available under type

number FC8021.

- Philips Clinic s-bag ` high ltration synthetic dustbags are available

under type number FC8022.

- Philips Anti-odour s-bag ` synthetic dustbags are available under type

number FC8023.

- Reusable dustbags (some countries only) are available under code

number 4322 004 93290.

Note: Please visit www.s-bag.com for more information about the s-bag.



- HEPA 13 washable lters are available under code number 4322 004

93350.



- Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the environment.



- Batteries contain substances that may pollute the environment. Always

remove the batteries before discarding the appliance or handing it

in at an ofcial collection point. Dispose of the batteries at an ofcial

collection point for batteries.





1 Replace the batteries when the ‘infrared active light’ does not light

up when you press any button.

 19

2 Use a screwdriver to remove the screw of the battery compartment

lid (1) and remove the battery compartment lid (2).

3 Insert two new AAA 1.5-volt alkaline batteries into the handle.

Note: Make sure that the - and + poles point in the right direction.

4 Reattach the battery compartment lid (1) and fasten the screw with

a screwdriver (2).



If you need service or information or if you have a problem, please visit

the Philips website at www.philips.com or contact the Philips Consumer

Care Centre in your country (you nd its phone number in the worldwide

guarantee leaet). If there is no Consumer Care Centre in your country, go

to your local Philips dealer.



This chapter summarises the most common problems you could

encounter with the appliance. If you are unable to solve the problem with

the information below, contact the Consumer Care Centre in your country.

Problem Possible cause Solution

The suction power is

insufcient.

You have selected a low

suction power setting.

Select a higher suction power setting.

The motor protection lter is

dirty.

Clean the motor protection lter.

The HEPA 13 lter is dirty. Clean or replace the HEPA 13 lter.

20

Problem Possible cause Solution

The nozzle, hose or tube is

blocked up.

To remove the obstruction, disconnect the

blocked-up item and connect it (as far as

possible) the other way around. Switch on the

vacuum cleaner to suck the obstruction out of

the blocked-up item.

The infrared remote

control (specic

types only) does not

function.

You have not inserted the

batteries properly or the

batteries are empty.

Insert the batteries properly or replace them.

See chapter ‘Replacement’.



If you do not nd the PostureProtect handgrip comfortable to use, you

may consider removing it.

1 Remove the screw cover strip from the PostureProtect handgrip.

2 Use a screwdriver to remove the screws of the PostureProtect

handgrip.

3 Remove the PostureProtect handgrip from the tube.

 21

Page is loading ...

Philips FC9178/01 User manual

This manual is also suitable for

Philips FC9178/01 User manual

in other languages

Related papers

Other documents