Kenmore Elite 79043800001 Installation guide

Brand: Kenmore Elite

Model: 79043800001

Category: Cookers

Type: Installation guide

This manual is also suitable for

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of fhls or any other appliance.

U.S.A.

IMPORTANT INSTALLATION INFORMATION

* All electric cooktops run off a single phase, three-wire or four-wire cable, 240/208 volt, 60 hertz, AC only electrical

supply with ground.

* Minimum distance between cooktop and overhead cabinetry is 30" (76.2 cm).

* 30" (76.2 cm) min. for

unprotected cabinet

24" (61 cm) min. for cabinet

with protected bottom

surface.

DO NOT apply any sealant

along the perimeter. The

cooktop must vent freely.

Cooktop Dimensions

Cooktop Cutout Dimensions

4" X 8" (10.2 cm x 20.3 cm)

opening to route armored cable

if a panei is present

Figure 1

303/4(78.1) 211/2(54.6) 33/4(9.5) 28z/s (73.3) 197/8(50.5) 2_/s (75.2) 293/4(75.6) 20s/s (51.8) 201/2(52.1) 41/2(11.4)

363/4(93.3) 211/2(54.6) 33/4(9.5) 35V4 (89.5) 197/8(50.5) 357/8(91.1) 36 (91.4) 20s/s (51.8) 201/2(52.1) 41/2(11.4)

All dimensions are stated in inches and (cm).

Allow 2" (5 cm) space below the armored cajole opening to clear the electric cable and

aJJow space for installation of the junction box on the wail at the back of the cooktop.

Printed in Canada

P/N 318205421 (1010) Rev. A

English - pages 1-8

Espa_ol - pages 9-16

Overhead Cabinet Should Not Exceed a

Maximum Depth of 13" (33 cm)

,, •

3o (76.2cm)Min..... .........................

Clearance Between the Top J K Min. Recommended

of the Cooking Platform L Distance Between

and the Bottom of an

Unprotected Wood or Metal

Cabinet

24" (61 cm) Min. when

Bottom of Wood or Metal

Cabinet is Protected by Not

Less Than 1/8" (0.3 cm)

Flame Retardant Millboard

Covered With Not Less

Than No. 28 MGS Sheet

Steel, 0.015" (0.4 mm)

Stainless Sted, 0.024" (0.6

mm) Aluminum or 0.020"

(0.5 mm) Copper.

Rear Edge of

Cutout and Nearest

Combustible Surface

Above Counfertop

18"

(45.7 cm) F

10"

25.4 cm)

2 1/2" (6.4 cm) Min. From

Edge of Cutout to Front Edge

of Countertop

12"

(30.5 cm)

Approximate Location

of Junction Box

J Min. From

Edge of Cooktop

Nearest

Combustible

Wall (Either Side

of Unit).

It is not recommended to

use drawer underneath

cooktop. Empty space is

needed for installation

purpose.

_To eliminate the risk of burns or fire by

reaching over heated surfaces, cabinet storage space located

above the cooktop should be avoided. If cabinet storage is

provided, risk can be reduced by installing a range hood that

projects horizontally a minimum of 5" (12.7 cm) beyond the

bottom of the cabinets.

Letters on this figure refer to chart

on front page except for J and K.

30" 7Y2" (19.1 cm) lY2" (3.8 cm)

Figure 2 = COUNTERTOP CUTOUT OPENING

Model and Serial Number Location

The serial plate is located under the cooktop.

When ordering parts for or making inquires about your

cooktop, always be sure to include the model and serial

numbers and a lot number or letter from the serial plate

on your cooktop.

Serlal plate is located under

the burner box of cookfop.

important Notes to the installer

1. Read all instructions contained in these installation

instructions before installing the cooktop.

2. Remove all packing material before connecting the

electrical supply to the cooktop.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

5. Only certain cooktop models may be installed over

certain built-in electric oven models. Approved

cooktops and built-in ovens are listed by the MFG ID

number and product code.

Importanf Note to the Consumer

Keep these instructions with your Use and Care Guide for

future reference.

_An extension cord must not be used

with this appliance. Such use may result in a fire,

electrlcal shock, or other personal injury.

3. The appliance should be connected to the fused

disconnect (or circuit breaker) box through flexible

armored or nonmetallic sheathed cable. The flexible

armored cable extending from this appliance should

be connected directly to the grounded junction box.

The junction box should be located as shown in

Figure 2 with as much slack as possible remaining in

the cable between the box and the appliance, so it

can be moved if servicing is ever necessary.

4. A suitable strain relief must be provided to attach

the flexible armored cable to the junction box.

iMPORTANT SAFETY

INSTRUCTIONS

° Be sure your cooktop is installed and grounded

properly by a qualified installer or service

technician.

° This cooktop must be electrically grounded in

accordance with local codes or, in their absence,

with the Natlonal Electrlcal Code ANSi/NFPA No.

70mlatest edition in the United States.

_The electrlcal power to the cooktop

must be shut off while llne connections are being

made. Failure to do so could result in serious injury or

death.

Provide Electrical Connection

Install the junction box under the cabinet and run

120/240 or 120/208 Volt, AC wire from the main circuit

panel. NOTE: DO NOT connect the wire to the circuit

panel at this time.

Electrlcal Requirements

Observe all governing codes and local ordinances.

1. A 3-wire or 4-wire single phase 120/240 or

120/208 Volt, 60 Hz AC only electrical supply is

required on a separate circuit fused on both sides

of the line (time-delay fuse or circuit breaker is

recommended). DO NOT fuse neutral.

2. A circuit breaker or fuse rated at 40 Amp is

recommended for the 30" model and a circuit

breaker or fuse at 50 Amp is recommended for the

36" model.

NOTE: Wire sizes and connections must conform with

the fuse size and rating of the appliance in accordance

with the National Electrical Code ANSI/NFPA No.

70=latest edition and local codes and ordinances.

Unpacking Instructions

1. Unpack and visually inspect the cooktop.

2. Be sure the bottle of cleaner conditioner packed

in the literature bag is left where the user can find

it easily. It is important that the ceramic-glass

cooktop be pretreated before use. See Cooktop

Cleaning and Maintenance section in the Use and

Care Guide.

Electrical Connection

Connect the flexible armored cable that extends from

the surface unit to the junction box using a suitable

strain relief at the point the armored cable enters the

junction box. Then make the electrical connection as

follows.

Electrical ground is required on this appliance.

V'___ Thls appliance is equipped with a

copper conductor flexible cable. If connection is made

to aluminum house wiring, use only special connectors

whlch are approved for joining copper and aluminum

wires in accordance with the National Electrical Code

and local codes and ordinances, improper connection

of alumlnum house wiring to copper leads can

result in a short circuit or fire. Follow the connector

manufacturer recommended procedure closely.

This appliance is manufactured with a supply wire and

a frame connected green or bare copper grounding

wire.

_DO NOT ground to a gas supply

pipe. DO NOT connect to electrical power supply

until appliance is permanently grounded. Connect the

ground wire before turning on the power.

if the cable from appliance is e_ed with 3 wires:

Where local codes permit connecting the appliance-

grounding conductor to the neutral (white) wire (see

figure 3):

1. Disconnect the power supply.

2. In the circuit breaker, fuse box or junction box,

connect appliance and power supply cable wires

as shown in figure 3.

_You may not ground the cooktap

through the neutral (white) wire if cooktop is used in

a new branch circuit installation (1996 NEC), mobile

home, recreational vehicle, or where local codes do

not permit grounding to the neutral (white) wire.

Cable from Power Supply

White Wire

(Neutral)

Black

Wires Wires

Box

Green Wire (Ground)

Cable from

appliance

U.L.-Listed Conduit

Connector

Figure 3 = 3=WIRE GROUNDED JUNCTION BOX

If cooktop is used in a new branch circuit installation

(1996 NEC), mobile home, recreatlona[ vehicle, or

where local codes DO NOT permit grounding to the

neutral (white) wire (see figure 4):

1. Disconnect the power supply.

2. In the circuit breaker, fuse box or junction box,

connect appliance and power supply cable wires

as shown in figure 4.

Cable from Power Supply

"_,_,_J_,_ rWhite Wire

Ground

Wire _[_ _/

Red _:_-.LII

Green Wir¢ _:_:--_ -U.L.-Listed Conduit

(Ground) _2VJ Connector

Cable from appliance

Figure 4 =4=WIRE GROUNDED JUNCTION BOX

_[f connecting to a 4=wire power

supply cable e[ectrlca[ system, the appliance frame

connected ground wire MUST NOT be connected to

the neutral wire of the 4=wire electrical system.

When grounding to the neutral (white) wire is

prohibited, you must use a 4=wlre power supply

cable. See Figure 4. Failure to heed this warning

may result in electrocution or other serious personal

injury.

NOTE TO ELECTRiCiAN: The armored cable leads

supplied with the appliance are UL-iisted for

connection to larger gauge household wiring. The

insulation of the leads is rated at temperatures much

higher than temperature rating of household wiring.

The current carrying capacity of the conductor wire is

governed by the temperature rating of the insulation

around the wire, rather than the wire gauge alone.

if the cable from aj0_iiance is equipped with 4 wires:

Where local codes permit connecting the appliance-

grounding conductor (wire) to the neutral (white)

wire (see figure 5):

1. Disconnect the power supply.

2. In the circuit breaker, fuse box or junction box,

connect appliance and power supply cable wires

as shown in figure 5.

Cable from Power Supply

Wh,it?Wire. / .----Black

u_eutraJ). __: Wires-

Wire

GroundWireH (Neutral)

(Bare or Green _.L[-Listed Conduit

Cable from appliance

Figure 5

3=WIRE GROUNDED JUNCTION BOX

This appliance is manufactured

wlfh a white neutral power supply and a frame

connected copper wire. The frame is grounded by

connection of grounding lead to neutral lead at the

termination of the conduit, if used in USA, in a new

branch circuit installation (1996 NEC), mobile home,

recreational vehicles, where local code do not permit

grounding trough the neutral (white) wire or in

Canada, disconnect the white and green lead from

each other and use ground lead to ground unit in

accordance wlfh local codes, connect neutral lead to

branch circuif=neufral conductor in usual manner see

Figure 6. If your appliance is to be connected to a 3

wire grounded junction box (US only), where local

code permit connecting the appiiance=groundlng

conductor to the neutral (white) see Figure 5.

If cooktop is used in a new branch circuit installation

(1996 NEC), mobile home, recreaflonaJ vehicle,

or where local codes DO NOT permit grounding

through the neutral (white) wire (see figure 6):

1. Disconnect the power supply.

2. Separate the green (or bare copper) and white

appliance cable wires.

3. In the circuit breaker, fuse box or junction box:

connect appliance and power supply cable wires

as shown in figure 6.

Cable from Power Supply

Ground

Ground Wire

(Bare or

Green Wire)

Wires]

__Black

U.L.-Listed Conduit

Junction Box Connector (or CSA

listed)

Cable from appliance

Figure 6

4=WIRE GROUNDED JUNCTION BOX

Ifconnecting to a 4=wlre power

supply cable electrical system, the appliance frame

connected ground wire MUST NOT be connected to

the neutral wire of the 4=wire electrical system.

NOTE TO ELECTRICIAN: The armored cable leads

supplied with the appliance are UL and CSA-

recognized for connection to larger gauge household

wiring. The insulation of the leads is rated at

temperatures much higher than temperature rating of

household wiring. The current carrying capacity of

the conductor is governed by the temperature rating

of the insulation around the wire, rather than the wire

gauge alone.

Cool{top installation

1. Visually inspect the cooktop for damage. Also make

sure all cooktop screws are tight (see Figure 5).

2. Install the retainer brackets. See Figure 6.

Hole located

under the burner

box to fix the

retainer bracket.

Position brackets

on unit cutout

center line as

shown.

Figure 7

4. Fix the cool<top to the bracket using the screws

supplied (see Figure 7).

The retainer brackets MUST be installed, to meet local

codes or, in their absence, with the Natlonal Electrical

Code ANSI/NFPA No. 70mlatest edition (see Figure

6).

Granite countertop installation

Granite Countertop Installation kit Div 22, Src 628, p/n

903061-9010 can be ordered through a Service Center,

by phone at |=800=4=MY=HOME ® or through our web site

at www.parisdlrect.com.

Cooktop Countertop

Spring

spacer

Retainer bracket

Figure 6

Checking Operation

Refer to the Use and Care Guide for operation.

_Do not touch cooktop glass or

elements. They may be hot enough to burn you.

Before You Call for Service

Read the Before You Caii for Service Checklist and

operating instructions in your Use and Care Guide.

It may save you time and expense. The list includes

common occurrences that are not the result of defective

workmanship or materials in this appliance.

Refer to your Use and Care Guide for Sears service

phone numbers, or call |mSOO-4-MYmHOMIF ®.

3. Set the cooktop into the countertop cutout.

NOTE: Do not use caulking compound; cool<top should

be removable for service when needed.

For typical under counter installation of an electric built-in oven see Figure below.

Only certain cooktop models may be installed over

certain built-in electric oven models. Approved

cooktops and built-in ovens are listed by the MFG

ID number and product code (see the insert sheet

included in the literature package and cooktop

installation instructions for dimensions).

To reduce the risk of

personal injury and

tipping of the wall

oven, the wall oven

must be secured to

the cabinet (s) by

mounting brackets.

208/240 Volt junction

box for built-in oven..

Approx. 3"

(Z5 cm)

Note 1

Cut an opening in wood base minimum 4" x 4"

(10.2 X 10.2 cm), 2" (5 cm) from left side filler

panel, to route armored cable to junction box.

Note 1: 4" x 4" (10.2 X 10.2 cm) opening to route

armored cable from cooktop to junction box.

Approx. 3", j

(z5cm)

208/240Volt

junction box

for Cooktop

Cabinet side filler

panels are necessary

to isolate the unit from

adjoining cabinets.

Cabinet side filler

height should allow for

installation of approved

cooktop models

36" Min.

(9!.4 cm) Min.

Unit will

overlap cutout

(minimum)

edges by I"

(2.5cm) 41/2" (11.5cm)

Max. _

3/4" (1.9 cm) plywood,

installed on two runners,

flush with toe plate.

Base must be capable of

supporting 150 pounds (68

kg) for 27" models and

200 pounds (90 I<g) for

30" models.

If no cooktop is

installed directly

over the oven unit, 5"

(12.7 cm) maximum

is allowed above the

floor.

CUTOUT DIMENSIONS

wmTM MIME GNT

27" (68.6 cm) 247/8" (63.2 cm) Min. 231/2" (59.7 cm) 271/4 '' (69.2 cm) Min.

Wall Oven 251/4" (64.1 cm) Max. Min. 281/4" (71.8 cm) Max.

30" (76.2 cm) 281/2" (72.4 cm) Min. 231/2" (59.7 cm) 271/4" (69.2 cm) Min.

Wall Oven 29" (73.7 cm) Max. Min. 281/4" (71.8 cm) Max.

Figure 10- TYPICAL UNDER COUNTER iNSTALLATiON OF A SINGLE ELECTRIC BUlLTqN OVEN

WITH AN ELECTRIC COOKTOP MOUNTED ABOVE

Page is loading ...

Kenmore Elite 79043800001 Installation guide

Brand: Kenmore Elite

Model: 79043800001

Category: Cookers

Type: Installation guide

This manual is also suitable for

Download PDF

report

in other languages

español: Kenmore Elite 79043800001 Guía de instalación

Kenmore Elite 79043800001 Installation guide

This manual is also suitable for

Kenmore Elite 79043800001 Installation guide

in other languages

Related papers

Other documents