Lolly & Me Taylor Assembly & Instruction Manual

Type
Assembly & Instruction Manual
Taylor
Changing Table
Adaptable as Your Child Grows Up
Assembly Instruction Manual
Questions? Call Us at 1-800-515-4056
Website: www.lollyandme.com
Adult assembly required due to the presence of small parts, sharp points & sharp edges.
Before assembly, read these instructions. Make sure all pre-assembled parts are tight. Store this instruction
manual for future reference.
Our goal is to improve the assembly process for the customer.
If you have any questions during assembly or you are missing parts
Do not return product parts to the retailer before contacting our customer service department for assistance.
Please follow contact instructions on page .
To prevent death or serious injury, always keep child within arm’s reach.
2
Assemble on soft surface to prevent damage to the product finish.
To make it easier to build your crib have a friend help during the assembly.
Ensure that all parts and components are located before beginning assembly.
Changing Table Warnings
Read all instructions before use of changing table.
Before each usage or assembly, inspect unit for damaged hardware, loose joints, loose bolts
and other fasteners, missing parts, or sharp edges. DO NOT use unit if any parts are missing,
or broken. Ask your dealer or call
LOLLY & ME at 1-800-515-4056 or write to 10301 Bren Road West,
# 0-379 Minnetonka, MN 55343
Periodically check all bolts and screws to maintain the stability of your changing table.
Never allow children to climb or hang on drawers, doors, or shelves.
Always secure this pad to the changing surface by restraint harness. See
instructions for more details.
Congratulations on Your Purchase!
Thank you for choosing a Lolly & Me product. Dont worry
about the assembly. Inside you will find understandable step-
by-step instructions with clear illustrations—it’ll be a piece of
cake! If you get stuck, ring us up at 1-800-515-4056. Need a
replacement part or is a part missing? Just call us and we’ll get
one sent off to you right away.
Remember to complete your product registration card and
mail it in to activate your products five year limited warranty.
You can also go online to www.lollyandme.com and complete
it there. Then—and this is the good part— you will be regis-
tered in our quarterly drawing for prizes that will look great
your little ones nursery!
Sincerely, Lolly & Me
Questions? Call Us at 1-800-515-4056
Website: www.lollyandme.com
3
Instructions for Assembly
Adaptable as Your Child Grows Up
OK
Lets Put This Baby
Together!
4
Taylor
Changing Table
Adult assembly required due to the presence of small parts, sharp points,and sharp edges.
Before assembly, read these instructions. Make sure all preassembled parts are tight and that
all neccessary hardware is included. Store the instruction manual for future reference. Our goal
is to improve the assembly process for you, our customer. If you have any questions during
assembly or you are missing parts, please contact us directly. Do not contact the retailer.
Do not return product parts to the retailer before contacting our customer service department
for assistance. We are here for you.
AB
C D
E
Table End (x2) Bottom Rail (x4)
Top Rail (x2) Top Panel (x1)
Shelf (x2)
FChanging Pad (x1)
5
M6x65mm Bolt (x12)
Belt (x1)
Hardware
aa
bb
nellA L
hcnerW
nellA S
hcnerW
6
7
STOP
IF YOU EXPERIENCE ANY
ISSUES WITH THIS PRODUCT
BEFORE YOU
RETURN THIS TO
THE RETAILER
PLEASE FOLLOW THE
PROCEDURES LISTED ON
THE FOLLOWING PAGE
8
PRODUCT ASSITANCE PROCEDURES
IF YOU HAVE ANY QUESTIONS DURING ASSEMBLY OR YOU ARE MISSING PARTS, PLEASE
CONTACT US DIRECTLY.
PROCEDURES TO FOLLOW SHOULD YOU HAVE ANY QUESTIONS:
FOR THE BEST AND MOST TIMELY SERVICE PLEASE CONTACT US VIA E-mail:[email protected]
phone us at 1-800-515-4056 or write to 10301 Bren Road West, # 0-379 Minnetonka, MN 55343
PLEASE PROVIDE THE FOLLOWING INFORMATION IN YOUR E-mail.
1. YOUR NAME
2. ADDRESS
3. BEST DAY TIME PHONE NUMBER
4. PLACE AT DATE OF PURCHASE
5. MODEL NUMBER, NAME AND COLOR OF YOUR PRODUCT
6. MANUFACTURER’S CODE (THE MANUFACTURER’S CODE CAN BE FOUND ON A LABEL
AFIXED TO THE BOX AS WELL AS A LABEL AFIXED TO THE CRIB ITSELF.)
7. SHORT DESCRIPTION OF THE ISSUES AND ATTACH PHOTOS IF POSSIBLE.
PLEASE INCLUDE SPECIFIC PART NUMBERS IN QUESTION FOR MORE EFFICIENT SERVICE.
SOMEONE WILL CONTACT YOU VIA E-mail OR PHONE TO HELP YOU WITH YOUR ISSUES.
IF YOU DO NOT HAVE INTERNET ACCESS, PLEASE FAX THE ABOVE INFORMATION TO :
612-573-6678
IF YOU DO NOT HAVE INTERNET OR FAX ACCESS, PLEASE CAL US AT 1-800-515-4056 AND BE
SURE TO HAVE ALL THE ABOVE INFORMATION TO GIVE TO THE CUSTOMER SERVICE
REPRESENTATIVE.
WE ARE HERE FOR YOU!
Attach 6pcs Rails (B & C) to Table End (A)
using 6pcs Bolts (aa).
Continue to Step 2...
9
Changing Table Assembly
1
A
M6x65mm Bolt (x6)
aa
aa
aa
aa
aa
Table End (x1)
B
Bottom Rail (x4)
C
Top Rail (x2)
CC
B
BB
B
A
Parts Needed:
"L" Allen Wrench
OR
"S" Allen Wrench
aa
aa
10
Parts Needed:
Insert 1pc Top Panel (D) and 2pcs Shelfs (E) to Rails.
Continue to Step 3...
Changing Table Assembly
2
EShelf (x2) DTop Panel (x1)
D
E
E
11
Attach the Table End (A) to Rails
use 6pcs Bolts (aa).
Continue to Step 4...
Changing Table Assembly
3
M6x65mm Bolt (x6)
aa
aa
aa
aa
aa
aa
aa
Parts Needed:
"L" Allen Wrench
OR
"S" Allen Wrench
ATable End (x1)
A
12
Attach the Belt (bb) to Top Panel (D).
Continue to Step 5...
Changing Table Assembly
4
Belt (x1)
bb
Parts Needed:
bb
D
13
Parts Needed:
Attach the Changing Pad (F) to Top Panel (D).
Continue to Step 6...
Changing Table Assembly
5
Changing Pad (x1)
F
F
14
Changing Table Assembly
6
Make sure that safety belt is fastened around
child, and adjusted so safety belt is snug around
child’s mid-section. Make sure buckle is securely
latched.
CLICK!
RESTRAINT HARNESS SYSTEM USE:
Place the infant on the Dressing/Changing Table
Foam Pad.
Position the Restraint Harness over the middle
of the infant’s torso and insert the buckled ends
into each other until they lock shut with a click.
Gently pull the loose end of the strap to lightly
snug the Restraint Harness around the infant.
Maintenance
Check fasteners periodically for tightness. DO
NOT over tighten. This may cause distortion or
breakage.
15
Disassembling Changing Table For Storage
To disassemble Changing Table for storage, follow steps in reverse.
Store all parts and hardware together in a safe place. Store the instruction manual for future
reference and for reassembly.
To clean Changing Table, use only mild household soap and warm water. Do not use bleach
or detergent. Do not use abrasive cleaners which can scratch the finish of the Changing Table.
Use clean soft cloths to wash, rinse and dry. With proper care, the quality finish will last long
time. Wood surfaces may be treated with a light application of a good grade non toxic furniture
polish.
1-800-515-4056
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Lolly & Me Taylor Assembly & Instruction Manual

Type
Assembly & Instruction Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI