2. Winners Only
  3. BTP1001F

Winners Only BTP1001F Assembly Instructions

  • Hello! I am a chat assistant and I have reviewed the assembly instructions for WINNERS ONLY bed models BTB/BTG/BTH/BTP1001F, BTG/BTH/BTP1001Q and BTB/BTG/BTH/BTP1001T. This document provides a detailed guide on how to assemble your new bed, including the use of various hardware and steps for installation with and without charging kit. I'm ready to answer any questions you may have about the assembly process or the components of your bed.
  • What should I do before unpacking the assembly parts?
    Is it recommended to assemble this alone?
    What should I do with screws and bolts?
Page 1 of 3
WINNERS ONLY
R
ASSEMBLY INSTRUCTIONS
Allen Bolts
Flat Washer
HB Left Leg
Slat
Support Leg
Slat
Support Leg
STEP 1: Attach the Wood Stretcher (D) to both Headboard Legs (A&B)
using provided hardware as shown on FIG.1
Caution:Pleasereadinstructionsthoroughlybeforeunpackingassemblyparts.Sharp,exposedstapletipscancauseinjury.Therefore,foryour
protection,pleaseremoveanyexposedstaplesusedinpacking.
Pleasekeepallhardwarepartsoutofthereachofchildren.
1.Werecommendthatyoushouldassemblethisproductwiththeassistanceofanotherperson;thiswillmakeassemblyeasierandwillhelpto
eliminatedamagetotheproductorinjurytopersonsduringassembly.
2.Besuretocheckallpackingmaterialscarefullyforsmallpartsthatmayhavecomelooseinsidethecartonduringshipment.
3.Pleasedonotovertightenscrewsorbolts.
4.Pleaseputallpartsonanon-abrasivefloorbeforeassembly,andfollowtheassemblystepstoassembleyournewlypurchasedproduct
correctlyandefficiently.
PROD.NO : BTG/BTH/BTP1001Q
PROD.NO : BTB/BTG/BTH/BTP1001F
WINNERS ONLYR
ASSEMBLY INSTRUCTIONS
Page 2 of 3
STEP 3: Attach both Bed Rails (F) to the Headboard
assembly (A,B,D&C) using the provided hardware as
shown on FIG.3
STEP 3: Attach both Bed Rails (F) to the Footboard (E)
using the provided hardware as shown on FIG.4
STEP 2: Attach the Headboard (C) to the Legs
assembly (A,B&D) using provided hardware as
shown on FIG.2
PROD.NO : BTG/BTH/BTP1001Q
PROD.NO : BTB/BTG/BTH/BTP1001F
Page 3 of 3
WINNERS ONLY
R
ASSEMBLY INSTRUCTIONS
STEP 5: Attach Support Legs (H) to Slats (G)as shown on FIG.5.
STEP 6: Attach Slats with Support legs (G&H) to the Side Rail
(F) using the provided hardware as shown on FIG.6
Assembly is now completed.
PROD.NO : BTB/BTG/BTH/BTP1001F
PROD.NO : BTG/BTH/BTP1001Q
WINNERS ONLY
ASSEMBLY INSTRUCTIONS
Page 1 of 1
WARNING: Before the removal or installation of charging kit disconnect charging kit from any electrical outlets.
Fig.1
STEP 2: Attach charging kit on the desired headboard leg
using 2 screws and phillips screwdriver as shown in Fig. 3.
Step 1: Using a phillips screwdriver remove the 2 screws
attaching the charging kit to headboard leg as shown in Fig.1.
BTB/BTG/BTH/BTP1001F
BTB/BTG/BTH/BTP1001T
Charging Kit Removal And Installation.
Note:
The Manufacturing label should not be visible
once charging kit is installed as shown in Fig. 2.
Fig. 3
Fig.2.
R
/