2. morse
  3. 310-1-115
310-1-115

morse 310-1-115 Operators Manual and Parts Diagram

  • Hello! I'm a chat assistant that has reviewed the Morse 310 Series 4576KIT-P Check Valve Upgrade Kit instructions. This document provides detailed instructions for upgrading the P. O. check valve on your Morse 310 Series Tilt-To-Load Drum Tumbler. It includes steps for removing old parts and installing the new hydraulic components. I'm ready to answer any questions you might have about the installation process or the kit components.
  • What is the purpose of this kit?
    What serial numbers are supported?
    What is included in the kit?
MORSE MFG. CO., INC. • 727 West Manlius Street • P.O. Box 518 • East Syracuse, NY 13057-0518
Phone: 315-437-8475 • Fax: 315-437-1029 • Email: service@morsedrum.com • Website: morsedrum.com
Copyright 2017 - Morse Mfg. Co., Inc. Form PL4576KIT-P (000000-236552) (Updated 3 Aug, 2017 2:54 PM) 1
The Specialist In Drum Handling Equipment
Kit # 4576KIT-P
P. O. Check Valve Upgrade Kit
Kit to upgrade P. O. check valve on Morse 310 Series Tilt-To-Load Drum Tumblers
with Serial Number 000000 to 236552
(See installation instructions on page 2)
ITEM QTY. PART # DESCRIPTION
1 1 4576B-P BODY, PO CHECK, 310
2 1 4594-P HYD FIT, SAE STRAIGHT SWIVEL
3 1 4593-P HYD FIT, SAE STRAIGHT
4 1 4576C-P CART, PO CHECK, 310
9 1 3612-P HYD FIT, SAE ADAPTER
10 1 3610-P HYD FIT, MALE ELBOW, SAE
1, 2, 3, 4, 9 & 10 1 4576KIT-P KIT, CONVERT 3131-P TO 4576-P
MORSE MFG. CO., INC. • 727 West Manlius Street • P.O. Box 518 • East Syracuse, NY 13057-0518
Phone: 315-437-8475 • Fax: 315-437-1029 • Email: service@morsedrum.com • Website: morsedrum.com
Copyright 2017 - Morse Mfg. Co., Inc. Form PL4576KIT-P (000000-236552) (Updated 3 Aug, 2017 2:54 PM) 2
The Specialist In Drum Handling Equipment
Kit # 4576KIT-P
P. O. Check Valve Upgrade Kit
Ensure that the drum holder is lowered to 1.
the oor and the hydraulic tilt cylinder (part #
4418-P) has no force on it.
Remove hydraulic hose #1 at the swivel 2.
tting (gure 1).
Remove hydraulic hose #2 at the swivel 3.
tting (gure 1).
Rotate the 339-P and 3131-P (gure 1) 4.
assembly about 90 degrees up to allow
clearance to remove the 339-P. This will not
be used.
Remove the 3131-P. This will not be used. 5.
Remove 3210-P (gure 1) adaptor from 6.
hydraulic cylinder port. This will not be used.
Install the upgrade hydraulics, as shown in 7.
gure 2, using the Morse part # 4576KIT-P
Kit to Convert Check Valve 3131-P to Check
Valve 4576-P.
Figure 1
Figure 2
Instructions to upgrade P. O. check valve on Morse 310 Series Tilt-To-Load Drum Tumblers
with Serial Number 000000 to 236552
/