Hill-Rom Overhead Patient Lifts Operating instructions

Hill-Rom
Brand
Hill-Rom
Model
Overhead Patient Lifts
Type
Operating instructions
LikoGuard™
Overhead Li
Instrucons for Use
LikoGuard™ L Prod. No. 3301030
LikoGuard™ XL Prod. No. 3301040
7EN121101 Rev.8
ENGLISH 2020
2www.hillrom.com
7EN121101 Rev. 8 • 2020
Table of Contents
1. Introducon ......................................................................................................................... 3
1.1 Symbol descripon ............................................................................................................... 4
1.2 Product descripon ..............................................................................................................5
1.3 Denions ............................................................................................................................6
2. Safety informaon ................................................................................................................ 7
2.1 Intended use .........................................................................................................................7
2.2 Maximum load......................................................................................................................8
3. Instrucons for use ............................................................................................................... 9
3.1 Check before every li ..........................................................................................................9
3.2 Move the li correctly .......................................................................................................... 9
3.3 Leave the li in the correct posion aer use ......................................................................9
3.4 Choosing the correct Sling .................................................................................................. 10
3.5 Plan the transfer ................................................................................................................. 11
3.6 Apply the sling to the paent ............................................................................................. 13
3.7 Connect the sling to the sling bar ....................................................................................... 13
3.8 Before liing the paent from the surface ......................................................................... 13
4. Funcons and controls ........................................................................................................ 14
4.1 Hand control ....................................................................................................................... 14
4.2 Hand control with display ...................................................................................................15
4.3 Menus and informaon ..................................................................................................... 16
4.4 Charging the li baery ................................................... ...................................................18
4.5 Alternave charging system ...............................................................................................18
4.6 Limit Switch ........................................................................................................................18
4.7 Operaon panel on li .......................................................................................................18
4.8 Emergency stop ..................................................................................................................19
4.9 Emergency lowering devices ..............................................................................................19
4.10 Quick aachment device .................................................................................................. 19
4.11 Latches on sling bar ..........................................................................................................20
5. Recommended liing accessories ...................................................................................... 20
6. Trouble shoong ................................................................................................................ 22
7. Inspecon and maintenance ............................................................................................. 23
7.1 Care and maintenance........................................................................................................23
7.2 Service ................................................................................................................................23
7.3 Service agreement ..............................................................................................................23
7.4 Expected life me ............................................................................................................... 23
7.5 Transport and storage.........................................................................................................23
7.6 Product changes .................................................................................................................23
7.7 Noce to Users and/or Paents in EU ................................................................................23
7.8 Recycling Instrucons ......................................................................................................... 24
8. Product data ...................................................................................................................... 25
8.1 Technical specicaons ......................................................................................................25
8.2 Dimensions ......................................................................................................................... 25
8.3 Electromagnec emissions ................................................................................................. 26
8.4 Electromagnec immunity .................................................................................................26
9. Cleaning and disinfecon ................................................................................................... 30
9.1 Equipment ..........................................................................................................................30
9.2 Cleaning instrucons ..........................................................................................................30
9.3 Disinfecon instrucons ..................................................................................................... 30
9.4 Use of cleaning and disinfecng agents on the LikoGuard™ Overhead li ........................31
3 www.hillrom.com
7EN121101 Rev. 8 • 2020
1 Introducon
Thank you for choosing a Liko™ product. With a genuine regard for safety and ease of use, paent handling soluons from
Liko have for decades been greatly appreciated by healthcare facilies worldwide. The LikoGuard™ overhead li series is a
new generaon plaorm built with experience combined with innovaon to meet the future of overhead li systems. With
powerful performance and enhanced safety design, the LikoGuard Overhead li is the latest addion to the long line of Liko™
quality products, designed and manufactured in Sweden.
Hill-Rom oers training in paent handling techniques in order to ensure that the equipment is used in a safe and eecve
way. For training on the use of this product, contact your local Hill-Rom representave.
Manufacturer:
Liko AB
Nedre vägen 100
975 92 Luleå
  + 46 - 920 - 474700
+ 46 - 920 - 474701
4www.hillrom.com
7EN121101 Rev. 8 • 2020
Symbol Descripon
Warning; this situaon requires extra care and aenon
.
Overload, the lis maximum load or its duty cycle are exceeded.
Cauon; Failure to follow the instrucons may lead to damage to the product.
Service required
Sound signal (audible)
Read the instrucons for use for detailed informaon.
Intended for indoor use.
The product has extra protecon against electric shock (Insulaon Class II).
Protecon level against electric shock Type B.
Risk ongoing, read instrucons for use before use.
This product complies with EC direcves.
IP N1 N 2 Protecon level against dust (N1) and protecon level against moisture (N2).
Manufacturer
Date of manufacture.
All baeries in this product must be recycled separately.
The material is recyclable.
STOP
�
Emergency stop
2
Emergency lowering
Product Idener
Serial Number
Medical Device
1.1 Symbol descripon
These symbols can be found in this document and/or on the product.
5 www.hillrom.com
7EN121101 Rev. 8 • 2020
 1.2 Product descripon
1. Li motor.
2. Operaon panel on li
- Electronic raising / lowering of li strap.
3. Li strap.
4. Mul-link; aachment point at li strap.
5. Emergency stop
- Mechanical Emergency lowering device.
6. Cable for hand control.
7. Hand control.
8. Sling bar.
9. Aachment point at sling bar.
10. Latches.
1
2
3
4
5
6
7
8
9
10
Read and understand the instrucons for use in its enrety before using the product.
Use of the product without a full understanding of the contents is subject to risk.
Always keep the instrucons for use close at hand for daily user access.
The safety and essenal performance of medical electrical equipment
Proof of Product compliance to North American safety standards
Non-ionizing electromagnec radiaon
X%
Y% ≤Tmin
Duty cycle for non-connuous operaon.
The maximum acve operaon me X% of any given me unit, followed by a deacvaon me, Y%.
The acve operaon me shall not exceed the specied me in minutes, T.
GS1 Data Matrix Barcode that may contain following informaon
(01) Global Trade Item Number
(11) Producon Date
(21) Serial Number
6www.hillrom.com
7EN121101 Rev. 8 • 2020
Liing area
The liing area, marked in grey, is the area under the actual overhead system where safe liing may be carried
out.
A overhead system can be constructed as a Straight-rail or a Traverse System.
Fig. X.
Straight-rail system Traverse system
Liing point
The liing point is the li's posion in the overhead system for transfers between dierent objecves.
See examples of li points below:
1. bed
2. wheelchair
3. water closet (toilet).
1.3 Denions
Never li a paent to or from a locaon outside of the li systems liing area!
Remember to always plan the liing operaon to and from the liing points!
1.
3.
2.
7 www.hillrom.com
Expected Life Time Load Case 1 Load Case 2 Load Case 3 Load Case 4
363 kg (800 Ibs.) 272 kg (600 Ibs.) 200 kg (440 Ibs.) 100 kg (220 Ibs.)
Total normal lis* 14500 19000 26000 52000
5
years
liing
frequency 8 lis/day 10 lis/day 14 lis/day 29 lis/day
7
years
liing
frequency 5 lis/day 7 lis/day 10 lis/day 20 lis/day
10
years
liing
frequency 4 lis/day 5 lis/day 7 lis/day 14 lis/day
7EN121101 Rev. 8 • 2020
2. Safety informaon
2.1 Intended Use
The LikoGuard™ Overhead li is part of a Liko™ overhead li system and is intended for use in following
environments: Health care, Intensive care, Emergency ward, Rehabilitaon, Habilitaon and Home healthcare
environment. An overhead li system can be used for:
- Liing between a bed and a wheelchair and for toileng.
- Liing to / from the oor.
- Liing together with a stretcher.
- Rehabilitaon training such as walking and standing.
The intended use for the LikoGuard overhead li does not include any liing by the paent / person alone. Liing
and transferring a person shall always be performed with the assistance of at least one caregiver for the paent.
The LikoGuard overhead li is used as a means to perform the li but is not in contact with the paent; therefore
we do not go into the various paent condions in this manual.
Essenal performance: The product shall not move unintenonally while being submied to disturbances.
Contact your Hill-Rom representave for support and advice.
The li must not be used beyond its expected life me.
*A normal li = 70 cm up of which 40 cm with load followed by 70 cm down of which 40 cm with load.
*A normal li = 27.6 inch. up of which 15.7 inch. with load followed by 27.6 inch. down of which 15.7 inch. with load.
The li must be installed by Hill-Rom trained personnel, in accordance with Liko’s current installaon instrucons
and recommendaons regarding the li system in queson. The li shall only be installed into Liko rails intended
for Liko overhead systems.
The li must not be modied under any circumstances. If you have any quesons, please
contact Hill-Rom.
The li may not be used in areas where ammable goods are stored or where ammable mixtures may occur.
Use of the product adjacent to other equipment should be avoided because it could result in improper operaon,
if such use is necessary, observe and verify that the other equipment is operang normally. Electromagnec
disturbance, may aect the liing performance of the product. Modicaon using other parts than original
spare parts (cables etc.) may aect the electromagnec compability of the product. Parcular care must be observed
when using strong sources of potenal disturbance, such as diathermy, etc, so that diathermy cables are not
posioned on or near the product. If you have quesons, please consult the responsible assisve device technician or
the supplier.
8www.hillrom.com
7EN121101 Rev. 8 • 2020
2.2 Maximum load
The total maximum load for a li system is always determined by the product in the system with the lowest specied
maximum load.
Li motor
Maximum load: = 272 kg (600 Ibs.)
Sling bar
Maximum load: = 363 kg (800 Ibs.)
Sling
Maximum load: = 200 kg (440 Ibs.)
Li rails
Maximum load: = 300 kg (660 Ibs.)
In this example, the maximum load for the
complete li system is dened by the sling.
The li system´s maximum load = 200 kg (440 Ibs.)
Example: Determine the maximum load for the li system below.
Li system
A Liko™ li system is a combinaon of products. Each product has its own maximum load marking. The lowest specied
maximum load of the products that comprises the system sets the maximum load for the complete li system.
The li system can contain following products; li rails, a li motor, a sling bar, a sling or other recommended
accessories. Idenfy the maximum load for the complete li system by reading the maximum load marking on each
product in the system. Contact your Hill-Rom representave for support and advice.
9 www.hillrom.com
7EN121101 Rev. 8 • 2020
3. Instrucons for use
3.2 Move the li correctly
RIGHT! WRONG!
3.1 Check before every li
Reviewing the li strap, check that:
– the li strap is free from wear or damage.
– the li strap is hanging vercally and can move freely.
– the li strap is not twisted and can enter the li unit without problem.
Reviewing the sling bar, check that:
– the sling bar is correctly assembled.
– the sling bar is free from wear or damage.
– the sling bar latches are funconing.
– the sling bar hangs in level and can move freely.
Reviewing the sling, check that:
– the sling selected is appropriate in terms of type, size, material and design with regard to the paent’s needs.
– the sling is being used correctly and safely, see instrucons for use for respecve sling.
– the sling is correctly applied to the paent, see instrucons for use for respecve sling.
– the sling is free from wear or damage, see instrucons for use for respecve sling.
– the strap loops of the sling are properly connected to the sling bar hooks, see instrucons for use for respecve sling.
Reviewing of other accessories, check that:
– the liing accessories are properly aached to the li.
– the liing accessories are correctly chosen in relaon to the paent’s needs.
– the liing accessories are not damaged.
– the liing accessories hang vercally and can move freely.
Before using the li, the user must be informed of the correct operaon of the li and accessories.
Read the instrucons for use for both the li and liing accessories.
Always check the li system according to "3.1 Check before every li"
3.3 Leave the li in the correct posion aer use
RIGHT!
WRONG!
Never leave children unaended in the vicinity of the li!
The hand control and cord must always hang free from the li with no contact with surrounding objects during
movement of a paent.
(Children will be exposed to risks that may lead to fatal injury i.e children falls.)
10 www.hillrom.com
7EN121101 Rev. 8 • 2020
3.4 Choosing the correct sling
Liko has a broad assortment of slings in a variety of models. Our basic models cover the most common liing needs
while our special designed models are for our users with special needs. All slings have their own unique characteriscs
and are available in variety of sizes. To choose the correct model and size of the sling is of highest importance for
safety, funcon and comfort for the user. For guidance and support in choosing the correct sling, contact your Hill-Rom
representave.
Note! Always read the instrucons for use that comes with Liko´s dierent sling models for correct and safe use of the
sling.
RIGHT! RIGHT!
If the sling is too big there is a risk that:
The paent can slip out of the sling see Fig. 5.
Fig. 5 Fig. 6
If the sling is too small there is a risk that:
The paent´s head will not be supported and may end
up close to the sling bar. The sling may seem ght to the
paent, see Fig. 6.
WRONG! WRONG!
11 www.hillrom.com
7EN121101 Rev. 8 • 2020
3.5 Plan the transfer
It is important to plan the liing operaon so it will be as smooth and safe as possible.
Consider the following points before the liing operaon:
– Always work ergonomically. Use the paent’s ability to acvely parcipate in the operaon.
– Make sure the paent is sing securely in the sling before transferring to another locaon.
– Never li a paent higher o of the underlying surface than necessary to complete the liing and transfer
procedure.
– Never move a paent further than necessary
– Changes to surrounding areas i.e arrange in furniture may cause interference.
When liing into or out of bed:
Work from the long side of the bed.
– Lock the bed wheels.
– Raise the bed to a comfortable working height when applying the sling.
– Follow the instrucons in the instrucons for use for the respecve slings
regarding correct applicaon and use.
– If possible, raise the back of the bed before commencing the li.
– Lower the bed during the liing and transferring of the paent in order to
minimize the distance between the paent and the oor during the liing
operaon.
Never leave a paent unaended during a liing situaon!
12 www.hillrom.com
7EN121101 Rev. 8 • 2020
When liing into or out of a chair/ wheelchair:
– Posion your chair so that the distance of the movement is minimized.
Lock the wheels of the wheelchair during transfers to or from a wheelchair.
– Posion the paent above the chair li point,
(Locked wheels on the wheelchair).
– Apply support to the paent’s knees to ensure the paent is supported by
the chair back once liing is completed.
13 www.hillrom.com
7EN121101 Rev. 8 • 2020
Fig. 12.
Fig. 10.
3.6 Apply the sling to the paent
Read the instrucon for use for the respecve sling regarding correct applicaon and use.
3.7 Connect the sling to the sling bar
• In order to aach the sling correctly to the paent and the sling bar, always study the instrucons for use for the sling
to be used in that instance.
• Li the latches to open the sling bar hooks, see Fig. 7, (
rst aach the upper strap loops and then the leg support loops to
each sling bar hook
)
• The sling is correctly aached when the sling bar hangs in level, see Fig. 8
• If the sling bar is not in level, see Fig. 9. refer to the instrucons for use for the sling in use.
3.8 Before liing the paent from the surface:
1. Check that the li strap is hanging vercally, is not twisted or askew, see Fig. 10, 11, 12.
2. Raise the sling bar so that the sling's straps are taut but without liing the paent from the surface.
Check that the strap loops are properly aached to the sling bar hooks, see Fig. 13.
Fig. 8.
Fig. 9.
RIGHT! WRONG!
RIGHT!
Fig. 11.
Fig. 7.
Fig. 13.
WRONG!WRONG!
The sling strap loops must be aached to the sling bar hooks so that the sling bar latches close completely,
prevenng involuntary unhooking of the sling strap loops.
14 www.hillrom.com
7EN121101 Rev. 8 • 2020
kg/lbs
4.1 Hand control
4 Funcons and controls
1. Operaon
2. Overloading by weight (the li stops) or Duty cycle exceeded
The li’s maximum load has been exceeded!
+ The li will stop, a signal sounds, and the symbol lights
up yellow. When the symbol goes out and the signal no longer
sounds, the li can be used again. Check the load and whether the
li system is being aected by surrounding objects.
The li´s Duty cycle has been exceeded!
The symbol ashes yellow.
- The li´s me in operang mode has been exceeded!
Lower the paent to a secure surface. Allow the li to rest for around 40 minutes or
unl the symbol is no longer is ashing if any of the up or down buons are pressed.
 When the symbol goes out, the li can be used again.
3. Service informaon
Service period! The symbol lights up yellow.
- contact your Hill-Rom representave for service of the li.
Read more about service under “7.2 Service and 7.3 Service
agreement” on page 22.
The li may be used as normal during this period.
4. Baery informaon
The li’s baery power is indicated by 4 lamps. Example: baery power is 100 % when
all lamps (1 - 4) lights, when only the lamp (1) lights, maximum 25% of baery power
remains. Note! If the lamp (1) blinks and a signal sounds, the li should be charged
at once.
5. Charging Informaon
When the hand control is connected to the wall charger the lights indicates:
Light 1 indicates yellow when the charger is connected to mains connecon
Light 2 indicates yellow when charging is ongoing
Light 2 indicates green when the baery is fully charged.
Read more at 4.4 "Charging the li baery", on page 18.
Up
Li movement is based on the hand control being held in the direcon
shown in the picture. The movement stops when the buon is released.
Down
Li movement is based on the hand control being held in the direcon
shown in the picture. The movement stops when the buon is released.
25%
50%
75%
100%
1 2 3 4
1
2
3
4
kg/lbs
5
1 2
1 2
1 2
Duty cycle
Duty cycle includes the me the li can be used in connuous operaon
and the subsequent inacve period required for the engine to cool down.
15 www.hillrom.com
7EN121101 Rev. 8 • 2020
4.2 Hand control with display
Informaon,
messages or
menus.
Symbols
1. Operaon
2. Display
Display window consists of two elds.
The small eld: shows symbols
The large eld: shows dierent informaon,
messages or menus.
Read more on page 17.
3. Manage display informaon in menus
4. Informaon when charging
Indicang lights on hand control:
Light 1 indicates yellow when the charger is connected to mains
connecon.
Light 2 indicates yellow when charging is ongoing
Light 2 indicates green when the baery is fully charged.
Read more at 4.4 "Charging the li baery", on page 18.
“Back” “Select” “Navigate”
When the li is in use the display window shows remaining baery power. The
baery power is indicated by four elds. Example, baery power is 100% when
all 4 elds are displayed. If only one eld is displayed, maximum 25% of baery
power remains. Note! If "Low baery" is displayed and a signal sounds, the
li should be charged at once, less than 10% baery power remains.
Up
Li movement is based on the hand control being held in the direcon
shown in the picture. The movement stops when the buon is released.
Down
Li movement is based on the hand control being held in the direcon
shown in the picture. The movement stops when the buon is released.
kg/lbs
1
2
3
4
kg/lbs
1 2
1 2
kg/lbs
1 2
16 www.hillrom.com
7EN121101 Rev. 8 • 2020
Note!
the Advanced Service menu is protected by a password.
Intended use is only by service technician trained by Hill-Rom.
For informaon, please refer to the Service Manual.
Totally
380
18
Heavy Lis
All lis
7 days
Usage
Totally
Usage
4.3 Menus and informaon
The hand controls display has a usage menu and service menu. In the usage menu two types of usage history can
be displayed. The rst is the history of lis performed in the past 7 day´s period. A heavy li is at minimum 200 kg
(440 Ibs.). To start gage 7 days from a given day, just reset the 7 day interval at the day for the gage to start. Read
more about heavy liing at page 8, 2.1 Intended use.
The second usage history is for every li performed regardless of weight since the li was taken in use the rst
me.
In the Service menu, sengs of 14 dierent languages to choose among is available. The Service menu also contain
informaon regarding when the next service is due.
Language
Password
Next
Due in:
27 days
Next
Past due:
3 days
Usage
Service
Service
7 days
All lis:
15
Heavy Liing
3
7 days
Reset
All lis:
0
Heavy Liing
0
Reset
7 days
Reset
7 days
to:
“7 days”
Select
“Yes or No”
7 day usage is
now reset
Back to
Usage menu
Back to “Usage”
menu
to:
“Total”
Ex. Li service
required within
27 days.
Ex. Li service
overdue, should
have taken place 3
days ago.
Back to
Main menu
Main menu
to:
“Reset”
to:
“Usage”
Select:
“Total”
Main menu
to:
“Service”
to:
“Language”
Select
“Service”
Select
“Usage”
to:
“Next”
choose language:
• Chinese
• Danish
• Dutch
• English
• Finnish
• French
• German
• Italian
• Japanese
• Norwegian
• Portuguese
• Russian
• Spanish
• Swedish
Back to
Main menu
- To display the menus; Hold down the buon on the hand control for 2 seconds.
Advanced Menu
Reset Reset
No
Yes Yes
No
Totally
7 days
Service
Usage
Next
Language
Advanced
17 www.hillrom.com
7EN121101 Rev. 8 • 2020
Symbols and Informaon
A pop-up message is displayed on screen for 5 seconds or unl any buon on the hand control is pressed.
Service required
No liing allowed!
Low baery level
Overload
operang me
Low baery!
- The baery should
be charged at once.
No contact!
- Hand control has
no contact with the li.
No liing allowed!
- An operaonal fault has
occurred. No liing is allowed,
lower the paent to a secure
surface.
Contact your Hill-Rom
representave for service.
Emergency stop acvated!
- Press in the emergency
stop buon on the
underside of the li to
reset.
(marked)
To Menus
- To display menus
Usage or Service;
Hold in the -buon
on the hand control for
2 seconds.
Service required
The symbol lights yellow.
- Book a me for service,
contact Hill-Rom.
Read more about service
at; 7.2 "Service" and 7.3
"Service agreement" on
page 22.
The li may be used as
normal during this period.
Overload! (maximum load)
+
The symbol lights yellow
and a signal sounds.
The li stops.
Check the load and
Check that the li is not
stucked to any surrounding
objects.
When the symbol goes out
and the sound signal goes
o, the li can be used
again.
Overload (Duty Cycle)
The symbol ashes yellow.
- The li’s Duty Cycle has been
exceeded. The li may be used
to lower the paent to a secure
surface. Allow the li to rest for
around 40 minutes or unl the
message is no longer displayed
when the buon or is
pressed.
When the symbol goes out, the
li can be used again.
Read more about Duty cycle at
pages 14 and 24.
STOP
�
Baery power informaon.
When the li is in use, the baery power status is displayed at the hand control´s display window.
Overload!
press
Open menus
2 seconds
Overload
duty cycle
18 www.hillrom.com
7EN121101 Rev. 8 • 2020
Charging with a wall charger (Prod. No. 3305010-3305050)
1. - Check that the li´s emergency stop is not acvated
- Check that the switch on the wall chargers right-hand side
is switched on, see Fig.1. (The switch can funcon as an emergency
circuit breaker in the event that a fault occurs).
2. Place the hand control in the wall charger
3. Light (1) on the hand control indicates yellow when the charger is
connected to the mains connecon, see Fig. 2.
4. The charger starts automacally and the light (2) indicates yellow
when charging is ongoing, see Fig. 2.
5. When the baery is fully charged the charger
automacally disconnects and the light (2) on the
hand control indicates green see Fig. 2.
4.4 Charging the li baery
It is important that the li baery is charged regularly. Always acvate the li´s charging system when not in use.
Full charge is achieved aer maximum 6 hours. With a fully charged baery approximately 35 normal* lis with a
load of maximum 100 kg (220 Ibs.) can be carried out. Regular charging is important to maximize baery life.
*A normal li = 70 cm (27.6 in) up on which 40 cm (15.7 in) is with a load, followed by 70 cm (27.6 in) down
of which 40 cm (15.7 in) is with a load.
NOTE! When the li is not in use acvate the li charging system. If the charger cannot be used, the emergency stop
funcon should be acvated to prevent draining the baery.
The li cannot be charged with the emergency stop acvated.
4.5 Alternave charging system.
The Liko In-Rail Charging system is an easy to use charging soluon that connuously charges the li when it is not
in use. When li is in use, the charging stops and will automacally resume in about 5 min aer nished use.
Hand control indicators, see 4.4 Fig 2.
Light 1 indicates yellow when the charger is connected to mains connecon
Light 2 indicates yellow when charging is ongoing
Light 2 indicates green when the baery is fully charged.
Access to the mains connecon shall not be blocked; to pull out the plug can in the event of a fault,
be used as a circuit breaker!
For more informaon, contact your Hill-Rom representave.
4.6 Limit Switch
The li moon stops by a light touch to the Limit Switch. If the li strap is fully rewound, pulled sideways or folded
over during liing so the Limit Switch i acvated, the li moon stops. If the Limit Switch has been acvated the li
can be restarted as soon as an example; the li strap not acvates the limit switch, in these cases a short response
delay is normal during restart.
Be aware that the li strap must be kept straight and taut when it runs in and out of the li unit.
Never use power sources other than the Liko™ recommended. See technical data page 24.
kg/lbs
Fig. 1
1  2
kg/lbs
Fig. 2
1 2
1 2
kg/lbs
1 2
1 2
19 www.hillrom.com
7EN121101 Rev. 8 • 2020
4.8 Emergency stop
Acvate emergency stop: Pull out the emergency stop buon using the red emergency stop cord.
4.9 Emergency lowering
Mechanical emergency lowering;
1. Pull down and 2. Drop the red emergency stop band, see Fig. 3a and 3b.
Repeat 1 -2 unl the paent has been lowered down to solid and secure base, and the li strap is slack.
Note! Apply load during a funconality check by pulling gently with one hand in the li strap.
4.10 Quick aachment device
Pull out the green buon on the Quick-Hook Mul ,see Fig. 4a. Aach the quick hook to the Mul-Link on the li strap
and release the buon. Quick-Hook Mul is now aached and locked to the the li straps Mul-Link, see Fig. 4b.
4.7 Operaon panel on li
If needed, the liing moon can also be controlled without the hand control via the respecve and
buons on the operaon panel.
Reset emergency stop: Push in the emergency stop buon.
Fig. 3a
1 2 (repetat 1-2 )
Fig. 3b
Always check that accessory with a quick aachment device is correctly aached to the li strap aachment.
Electrical Emergency lowering; use hand control or the operaon panel at the li motor. Note! The Emergency
Stop shall not be acvated! Press the down buon to lower the paent to secure surface and the li strap
is slack, see page 19 “4.7 Operaon panel on li”, or page 14 “4.1 Hand control”.
g. 4b
Fig. 4a
Mul -Link
Quick-Hook Mul
20 www.hillrom.com
7EN121101 Rev. 8 • 2020
SlingGuard™ 450 with Quick-Hook Mul Prod. No. 3308520
Maximum load 363 kg (800 Ibs.)
SlingGuard™ 450 Prod. No. 3308020
Maximum load 363 kg (800 Ibs.)
Sling Cross-bar 450 Prod. No. 3156021
Maximum load 300 kg (660 Ibs.)
(Requires, Fixed kit 4, Prod. No. 3308860 )
Sling Cross-bar 670 Prod. No. 3156018
Maximum load 300 kg (660 Ibs.)
(Requires, Fixed kit 4, Prod. No. 3308860)
FlexoStretch™ Prod. No. 3156057
Maximum load 300 kg (660 Ibs.)
(Requires, Fixed kit 4, Prod. No. 3308860)
LikoStretch™ Mod 600 IC Prod. No. 3156065B
(B = wider model)
Maximum load 250 kg (550 Ibs.)
(Requires, Fixed kit 4, Prod. No. 3308860)
OctoStretch™ Prod. No.3156056
Maximum load 200 kg (440 Ibs.)
(Requires, Fixed kit 4, Prod. No. 3308860)
LikoScale™ 350 Prod. No. 3156228
(Requires Quick-Hook Kit 1 Prod. No. 3308810 or Fixed Kit 1, Prod. No. 3308820)
For United States and Canada only:
LikoScale 200, Max. 200 kg (440 Ibs.) Prod. No. 3156225
LikoScale 400, Max. 400 kg (880 lbs.) Prod. No. 3156226
(Requires Quick-Hook Kit 1 Prod. No. 3308810 or Fixed Kit 1, Prod. No. 3308820)
Contact your Hill-Rom representave for more informaon.
5. Recommended liing accessories
For guidance and support in choosing the correct sling, contact your Hill-Rom representave.
Below you nd liing accessories suitable for the LikoGuard™ Overhead li.
To use other liing accessories than those recommended by Liko™ can entail risk.
4.11 Latches on sling bar
(Paent will be exposed to risks that may lead to fatal injury i.e paent falls.)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Hill-Rom Overhead Patient Lifts Operating instructions

Hill-Rom
Brand
Hill-Rom
Model
Overhead Patient Lifts
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents